1. DL manuals
  2. WalimeXPro
  3. Camera Flash
  4. VC-1000
  5. Instuction Manual

WalimeXPro VC-1000 Instuction Manual

Manual is about: studio flash

Summary of VC-1000

  • Page 1

    Gewerbering 26 86666 burgheim tel. +49 84 32 / 9489-0 fax. +49 84 32 / 9489 - 8333 email: info@foto-walser.De www.Foto-walser.De copy of instruction manual studio flash series vc-200 bis vc-1000

  • Page 2

    Content 1. How to understand the instruction manual ...................................... 3 1.1.Markings on the device ................................................................ 3 1.2.Markings in the manual ............................................................... 4 2. Important safety ...

  • Page 3

    Thank you very much for your confidence. We wish you much pleasure and success with your studio flash. The walimex pro studio flash series vc is especially developed for ambitious beginners and professional users. The vc series is perfectly suitable for studio, portrait, person, nude and product pho...

  • Page 4

    Warning danger of crashing, entrapment, burning and fire through the falling down of the device. The weight of the flash is, depending on the model (vc-200 to vc-1000), up to 3,3kg. The modeling lamp, flash tube and reflector could heat up up to 240°c. Make sure, that the device is always positioned...

  • Page 5

    Don´t cover the ventilation slots of the device during operation. Remove easily inflammable materials. Warning danger of burning on hot parts the modeling lamp and flash tube could heat up up to 240°c, the reflector up to 75°c and the flash housing up to 45°c. Don´t touch the parts during operation ...

  • Page 6

    4.3. Warning please note the safety notes in the respective chapters throughout operation. 1. Demount protection cap. 2. Mount reflector. 3. Insert modeling lamp. 4. Mount umbrella (optional). 5. Connect to power supply. 6. Switch on device. 7. Adjust modeling lamp. 8. Adjust flash output. 9. Adjust...

  • Page 7

    1. Mounting of reflector: switch off device. See switch the device on and off . Cool down the device. Warning! Danger of burning on reflector, modeling lamp and flash tube. Please cool down approx. 30 minutes. Demount protection cap. See demount and mount protection cap . Push back unlocking lever a...

  • Page 8

    8. Connect to power supply 6. Switch off device. See switch on and off of device . 7. Compare the local power supply with the connected load of the device. If the values differ, please contact info@foto-walser.De or tel. +49 843294890. 8. Connect the power cord with the socket on the device and with...

  • Page 9

    1. Switch on device. See switch on and off of device . 2. Turn control output power until the digital display output power shows the desired output. When the device reached the adjusted flash output, led test lights up. 3. Trigger test flash: press push-button test. The led test goes out and lights ...

  • Page 10

    10. The other end of the sync cord should be connected with the pc jack socket of the camera. Prepare flash trigger through remote receiver (optional) advice: please note the user information of the remote receiver manufacturer. 1. Connect the cable of the remote receiver with the socket for the syn...

  • Page 11

    11. Mount on tripod (optional) advice: please note the user information of the tripod manufacturer. Caution select a tripod of suitable weight and dimensions. See technical specifications . Make sure, that the tripod with the mounted device has a tilt and skid resistant stand. A locking lever b lock...

  • Page 12

    The modeling lamp goes out. The led model goes out. Advice: if you don´t switch off the modeling lamp before switching off the device, the modeling lamp will light up automatically, when switching on the device again. 14. Flash trigger warning fire danger through overheating. Continuous rapid sequen...

  • Page 13

    3. Demount reflector and all power and connecting cables. 4. Clean the device if necessary. See cleaning . 5. Put the device and all demounted elements into the original styrofoam packing and carry and store them according to the requirements in the technical specifications. See technical specificat...

  • Page 14

    Part of the device cleaning housing use a microfiber cloth to remove light and stubborn dirt. Modeling bulb, flash tube wipe off with dust brush or dry, soft cloth advice: don´t clean the modeling bulb and flash tube with water. Even small residues on the bulbs could lead to bursting reflector remov...

  • Page 15

    Hold the flash tube at the right and left side of the socket. Caution! Danger of cutting and splitting through breaking flash tube. Just touch the flash tube in the range of the plug-in contact and not at the levitated flash ring. Agitate the flash tube carefully and pull out from the socket. 4. Att...

  • Page 16

    4. Re-adjust the flash output on the desired value. 18. Accessories and options you can find extensive accessories for your walimex pro studio flash in our webshop. 19. Spare parts part of the device order number flash tube vc-200/300 until serial number 0903ch116304 15209 flash tube vc-200/300 star...

  • Page 17

    22. Overview about the operation panel a digital display output power j led model i b push-button slave k led model ii c led slave 1 l led audio d led slave 2 m led test e led slave 3 n control output power f push-button model o main switch o/i (off/on) g push-button model p connecting socket for sy...