- DL manuals
- Walker
- Snow Blower
- 5600-20
- Operator And Parts Manual
Walker 5600-20 Operator And Parts Manual
Summary of 5600-20
Page 1
O o p p e e r r a a t t o o r r ' ' s s a a n n d d p p a a r r t t s s m m a a n n u u a a l l single stage snowblower 5600-20 model serial no. 20051300 and up om 0352sb-a 10/05.
Page 2: Foreword
Foreword thank you... For purchasing a walker snowblower. Every effort has been made to provide you with the most reliable product on the market, and we are sure you will be among our many satisfied customers. It for any reason this product does not perform to you expectations, please contact us at ...
Page 3: Introduction
Introduction om 0352sb-a 1 introduction – to the purchaser ...................................................................................................3 safety precautions .....................................................................................................................4 be...
Page 4: Table of Content
Table of content om 0352sb-a 1 adjustments .................................................................................................................................18 deflector adjustment............................................................................................................
Page 5: Table of Content
Table of content om 0352sb-a 2 t o the p urchaser all products are designed to give safe, dependable service if they are operated and maintained according to instructions. Read and understand this manual before operation. This manual has been prepared to assist the owner and operators in the safe op...
Page 6: Safety Precautions
Safety precautions om 0352sb-a 3 safety first this symbol, the industry's "safety alert symbol", is used throughout this manual and on labels on the machine itself to warn of the possibility of personal injury. Read these instructions carefully. It is essential that you read the instructions and saf...
Page 7
Safety precautions - continued om 0352sb-a 4 n otice a safe operator is the best assurance against accidents. All operators, no matter how experienced they may be, should read this operator's manual and all other related manuals before attempting to operate the snowblower. Please read the following ...
Page 8
Safety precautions - continued om 0352sb-a 5 snowblower operation 1. Before leaving the tractor/snowblower unattended, take all possible precautions. Park the tractor/snowblower on level ground, place the transmission in neutral, set the parking brake, disengage the pto, lower the snowblower to the ...
Page 9
Safety precautions - continued om 0352sb-a 6 23. Make sure the tractor is counterweighted as recommended by your dealer. Weights provide the necessary balance to improve stability, traction and steering. 24. Always make sure all snowblower components are properly installed and securely fastened befo...
Page 10
Safety precautions - continued om 0352sb-a 7 m aintenance always use genuine parts when replacement parts are required 1. Keep the tractor and snowblower properly maintained. 2. Park the tractor/snowblower on level ground, place the transmission in neutral, set the parking brake, disengage the pto, ...
Page 11: Safety Precautions
Safety precautions om 0352sb-a 8 s torage before storing the snowblower, certain precautions should be taken to protect it from deterioration. 1. Clean the snowblower thoroughly. 2. Make all the necessary repairs. 3. Replace all safety signs that are damaged, lost, or otherwise become illegible. If ...
Page 12: Decals
Decals om 0352sb-a 9 660263 657762 657761 660988 660263 661051.
Page 13: Assembly
Assembly om 0352sb-a 10 s nowblower a ssembly the snowblower is assembled at the factory, however, snowblower kits must be assembled. Use the present manual and lay out all parts for assembly. Separate bolts and nuts into various sizes. After assembly, torque all the bolts according to the " torque ...
Page 14: Assembly
Assembly om 0352sb-a 11 8. Figure 3: install the pedal stopper (item 1), the bent portion facing the snowblower and secure in place with two 1/4"nc x 5/8" hex. Bolts (item 2) and two 1/4"nc serrated flange nuts (item 3). Tighten firmly. 9. Figure 3: attach the closed end of the tension spring (item ...
Page 15: Assembly
Assembly om 0352sb-a 12 16. Figure 5: place the hand guard (item 2) inside the chute (item 1) and align the holes. Fasten with four 1/4"nc x 1/2" hex bolts (item 3) and four 1/4"nc serrated flange nuts (item 4). Tighten firmly. 17. Figure 6: place the chute (item 1) on the chute base (item 8). 18. F...
Page 16: Assembly
Assembly om 0352sb-a 13 snowblower installation on the tractor 1. Remove the mower deck from the tractor if necessary. Refer to the appropriate tractor owner’s manuel. 2. Figure 8: attach each lift chain (item 5) to the lift bracket (item 1) with a 5/16" nc x 1 1/4" bolt (item 6) and a 5/16" nc nylo...
Page 17: Assemblage
Assemblage om 0352sb-a 14 5. Figure 10: lightly grease the tractor support arms (item 1). 6. Figure 10: align the mounting tubes (item 2) with the tractor support arms (item 1) and slide the snowblower assembly onto tractor support arms (item 1). 7. Figure 10: reaching under the tractor, pull the ri...
Page 18: Assembly
Assembly om 0352sb-a 15 13. Figure 12: reinstall the gearbox shield (item 1) and the two serrated flange bolt 5/16"nc x 1/2" (item 2). Installation of tire chains (optional) 1. Remove the tractor wheels. 2. Attach the 2 tire chains to the wheels. 3. Place the wheel spacer plates on the lug bolts. Th...
Page 19: Operation
Operation om 0352sb-a 16 warning: before operating the snowblower, become familiar with the location and function of all operator controls. Knowing the location, function, and operation of these controls is important for safe and efficient operation of the snowblower. Tractor controls refer to the a...
Page 20: Operation
Operation om 0352sb-a 17 caution: if the auger strikes a solid object or the machine begins to vibrate abnormally, immediately disengage the pto clutch, stop the engine and wait for all moving parts to stop. Disconnect the fuel solenoid wire (diesel engines) or the park plug wire(s) (gasoline engine...
Page 21: Operation
Operation om 0352sb-a 18 a djustments attention : to avoid personal injury, be sure the tractor engine is off, the drive shaft disengaged, and all movement has stopped before making any adjustments. Deflector adjustment set the angle of deflection according to the distance the snow must be thrown. T...
Page 22: Operation
Operation om 0352sb-a 19 s now removal methods when removing snow, do not use the snowblower as a dozer blade to push snow. Let the snowblower work its way through deep drifts. If the speed of your tractor is too fast, the snowblower may become overloaded and clog. For best results, raise the snowbl...
Page 23: Maintenance
Maintenance om 0352sb-a 20 shearbolt replacement 1. To replace the shearbolt, take off the gearbox shield by removing the two 5/16"nc x 1/2" flange bolts. The hole in the plate helps remove the shearbolt if fragments remain in the hole. 2. Replace the 5/16"nc x 2 1/4" shearbolt a genuine replacement...
Page 24: Maintenance
Maintenance om 0352sb-a 21 lubrication description interval lubrication required 8 hours grease each universal joint driveline 24 hours separate the sliding parts and cover each part with grease driving chain 2 hours and after each operation lubricate with chain saw lubricant gearbox every month che...
Page 25: Parts
Parts om 0352sb-a 22 i ntroduction all parts are illustrated in "exploded views" which show the individual parts in their normal relationship to each other. Reference numbers are used in the illustrations. These numbers correspond to those in the "reference number" (ref) column, and are followed by ...
Page 26: Parts
Parts om 0352sb-a 23 s nowblower a ssembly.
Page 27: Parts
Parts om 0352sb-a 24 s nowblower a ssembly r ef . D escription q ty . P art # 1 snowblower housing and foot rest 1 667619 2 1 stage auger 1 667620 3 cutting edge 1 667643 4 skid shoes 2 667626 5 chain guard 1 667629 6 driveline shield 1 667630 7 gearbox shield 1 667631 8 pedal stopper 1 667632 9 bea...
Page 28: Parts
Parts om 0352sb-a 25 d rive s ystem r ef . D escription q ty . P art # 1 gear box 1 4500056 - oil seal 2 662630 - bearing 4 661728 - plug 3/8" 1 661739 o-ring 1 664656 2 male driveline série 06 1 4700102 3 drive shaft 1 667624 4 shear bushing 1 667625 5 bearing flange 2 holes - ø1" 2 654787 6 1" bea...
Page 29: Parts
Parts om 0352sb-a 26 r otation s ystem r ef . D escription q ty . P art # 1 hand guard 1 667622 2 handle support 1 667628 3 chute stopper 1 667644 4 handle 1 667627 5 spacer ring 2 667645 6 retaining plate 3 657333 7 grommet ø.680 of hole 2 665959 8 plastic handle ø1/2" x 3" lg. 1 656797 9 hex. Bolt...
Page 30: Parts
Parts om 0352sb-a 27 c hute a ssembly r ef . D escription q ty . P art # 1 chute 1 667646 2 deflector 1 665738 3 polyethylene deflector 1 667623 4 plastic rotation bushing 1 665948 5 knob 5/16"nc 1 657309 6 nylon flat washer ø7/16" 3 658468 7 carriage bolt 5/16"nc x 5/8" ptd 3 0300001 8 machine scre...
Page 31: Torque Specification Table
Torque specification table om 0352sb-a 28 general specification table use the following torques when special torques are not given note: these values apply to fasteners as received from supplier, when dry. These values do not apply if lubricants are used. Bolt sizes (sae) torque inches pounds-foot n...
Page 32
Printed in canda.