Walkera Runner 250 PRO Quick Start Manual - 4.0 Attention Before Flying

Summary of Runner 250 PRO

  • Page 1

    Www.Walkera.Com quick start guide 18th-oct-2016 v1.0

  • Page 2: Contents

    -2- 4 3 7 8 8 9 6 9 13 16 16 16 17 18 12 13-14 5 6 6 1.0 get to know your aircraft 2.0 get to know your remote controller 3.0 specifications 4.0 attention before flying 5.0 charge the battery 6.0 prepare the remote controller 7.0 prepare the aircraft 8.0 ready to fly 15 15 10-12 8.1 starting the air...

  • Page 3

    -3- the runner 250 body is created using cfp for outstanding crash survivability. Modern industrial and modular design, improves the product performance and permit easy maintainance and upgrades. Advanced 5.8ghz live video and osd system, for a unforgettable visual fpv experience. Equip with dual gp...

  • Page 4

    -4- DEVO-7 gps-hold mode manual mode mix switch to “0” mix switch to “1” mix switch to “2” return to home 2.0 get to know your remote controller equipped with the manual mode / gps hold mode / one key return to home / circle flight / hyper ioc, camera controlling switches, the runner 250 is easier t...

  • Page 5: 3.0 Specifications

    -5- frequency : output power : current drain : power supply : output pulse : 2.4ghz dsss ≤100mw ≤230ma(100mw) 5# battery 8x1.5v or nimh 8x1.2v 1600-2000mah 1000-2000ms(1500ms neutral) 205mm 221mm 143mm 117mm 3.0 specifications aircraft main rotor dia.: overall (l x w x h): weight: remote controller:...

  • Page 6: 4.0 Attention Before Flying

    -6- attention: please refer to page 18 for details of ga005 balance charger. Power adapter ga005 charger 11.1v 2200mah lipo battery 3 cell dc 11.1v battery box 1) the runner 250 is recomended for pilots, 14 years or older, with rc hobby experience. 2) only fly the runner 250 in dry weather, with low...

  • Page 7: 7.0 Prepare The Aircraft

    -7- 7.0 prepare the aircraft install 5.8g antenna firstly install 5.8g antenna onto the transmitter, and tighten with open-end wrench. Open-end wrench install propellers fix the cw propeller( ) onto the cw motor according to the direction of blue arrow, and fix the ccw propeller( ) onto the ccw moto...

  • Page 8: 8.0 Ready to Fly

    -8- 8.1 starting the aircraft 8.0 ready to fly attention: place the aircraft in a wide open space, with the rear facing you. (this position is known as “tail in”) put all the function switches to the 0 position, put all trims and dials to the middle position, move the throttle to the lowest position...

  • Page 9

    -9- motor unlock 8.2 gps indicator lights when the right red led light (gps) begin to flash, you can work gps function. 8.3 motor unlock / lock quick start guide motor lock notice: the motors are locked by default after successful binding. Test: push the throttle stick up a little, the motors will n...

  • Page 10: 9.0 Operation Instruction

    -10- attention: gps hold mode ground mix switch to “1” position fmod(fmd) switch to “2” position mix throttle stick return neutral circle flight 9.0 operation instruction 1) make sure that the received gps signal (right red led light blinks). 2) in the gps mode, there are altitude hold, fixed point,...

  • Page 11

    -11- mix 25m return to home aircraft with home point horizontal distance > 30m a. If the flight altitude is higher than 25m, the aircraft will keep the current altitude and return above the home point then descend vertically. B. When the flight altitude is lower than 25m, the aircraft will elevate a...

  • Page 12: 10.0 End Flying

    -12- deram baron aka proximity fpv obstacle flying attention: 1) dream baron is more suitable for experienced pilots, highspeed obstacle avoidance flights require advanced skills. 2) recommended fpv range 300m depending on enviroment. 3) avoid flying over people, animals, do not fly over crowds, con...

  • Page 13: 11.0 Additional Remarks

    -13- 11.0 additional remarks selec name up/dn model name ent model 0 1 250pro type up/dn model type ent model heli aero boot screen(main interface) 11.1 devo 7 remote controller setting press up or dn to select “mod 1”, press ent to confirm and then press ext to return to model. Press r or l button ...

  • Page 14

    -14- up/dn ent r/l dn r/l dn r/l dn r/l dn r/l model outpu model gear mix model gear act model flap act model flap fmod model aux2 gear model aux2 act dn r/l wing up/dn model wing ent model wing norm press r or l to select norm, press ent to confirm and then press ext to return to model. Output afte...

  • Page 15

    -15- 11.2 tx5834(fcc)/tx5835(ce) video transmitting channel selection port introducton 1. Position of 5.8g antenna 2. Transmitter code switch 3. Osd code switch there are 8 channels avilable, chose the best channel based on the image quality on your screen. Select the channel by adjusting the dip-sw...

  • Page 16

    -16- www.Walkera.Com attention: 11.4 introduction for fcs-250 main flight controller flexible flat cable connection the metal surface of flexible flat cable plug should be inserted upward to main controller port properly. The metal surface of flexible flat cable plug should be inserted downward to p...

  • Page 17

    -17- ground if there is circles or drift in flying, please calibrate the compass. (the motor must be locked and left red led light go out ) please calibration outdoors and far away from strong electromagnetic interference. Attention: 11.7 compass calibration the compass calibration steps are as foll...

  • Page 18

    -18- 1000ma dc15-18v 12.6v 8.4v 4.2v 0v note: 1. Before charging, please read the instructions; 2. For indoor use only and forbidden to expose to rain; 3. Warning: against recharging the non-rechargeable batteries. Statu s led ≤800ma 62.5 x 47 x 20.8mm 46g input voltage input current output current ...

  • Page 19

    User manual is subject to change without prior notice. Please go to walkera official website to get the latest version. Tel: 400-9318-878.