- DL manuals
- Walter Drake
- Saw
- JET HBS-1018W
- Operating Instructions And Parts Manual
Walter Drake JET HBS-1018W Operating Instructions And Parts Manual
Summary of JET HBS-1018W
Page 1
Operating instructions and parts manual horizontal band saw models hbs-916w; hbs-1018w walter meier (manufacturing) inc. 427 new sanford road lavergne, tennessee 37086 part no. M-414468 ph.: 800-274-6848 revision g1 06/2010 www.Waltermeier.Com copyright © 2010 walter meier (manufacturing) inc..
Page 2: Warranty And Service
2 warranty and service walter meier (manufacturing) inc., warrants every product it sells. If one of our tools needs service or repair, one of our authorized service centers located throughout the united states can give you quick service. In most cases, any of these walter meier authorized service c...
Page 3: Table Of Contents
3 table of contents warranty and service ......................................................................................................................2 table of contents ............................................................................................................................
Page 4
4 warning 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscur...
Page 5
5 21. Provide for adequate space surrounding work area and non-glare, overhead lighting. 22. Keep the floor around the machine clean and free of scrap material, oil and grease. 23. Keep visitors a safe distance from the work area. Keep children away. 24. Give your work undivided attention. Looking a...
Page 6: Introduction
6 introduction this manual is provided by walter meier (manufacturing) inc., covering the safe operation and maintenance procedures for a jet model hbs-916w or hbs-1018w band saw. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instruc...
Page 7: Uncrating and Cleanup
7 uncrating and cleanup note: read and understand the entire manual before attempting setup or operation. 1. Finish uncrating the saw and inspect for damage. Should any have occurred, contact your local distributor. 2. Remove all bolts attaching machine to shipping base. 3. Leave packing material be...
Page 8: Electrical Connections
8 4. Carefully lift motor and line up holes in the motor mounting plate and the motor bracket. 5. Slide motor support shaft into motor mount bracket to hold the motor in place. 6. Fasten shaft with nut and washer. 7. Loosen strain relief nut on the motor junction box. Remove the junction box cover. ...
Page 9: Controls
9 to convert the hbs-916w from 115v to 230v, the following items will have to be changed: main motor – follow diagram inside junction box cover. Coolant pump – remove chip pan on front of saw, remove junction box cover on pump, and follow diagram inside junction box cover. Control transformer – open...
Page 10: Adjustments
10 7. Material to be cut must be securely held in vise. 8. Check to see that coolant level is adequate and turn on coolant pump if material to be cut requires it. Machine should be filled with four gallons of the proper coolant mixture. Follow the directions on the product maker’s label and fill the...
Page 11
11 adjusting feed rate rate of feed is adjusted by turning the cutting pressure control knob on the control panel. Rate of feed is important to band saw performance; excessive pressure may break the blade or stall the saw. Insufficient pressure rapidly dulls the blade. Material chips or shavings are...
Page 12
12 9. Tension blade to approximately 25,000 lbs. Of blade tension, as indicated on the blade tension indicator found on the tension wheel shaft housing. 10. Attach wire brush to the wire brush post with screw and washer. Adjust wire brush post so that brush just comes into contact with blade teeth. ...
Page 13
13 automatic shut‐off adjustment the motor should shut off immediately after the blade has cut through the material and just before the head comes to rest on the horizontal stop bolt. If the machine continues to run after the workpiece has been fully cut, locate and adjust the micro switch mounting ...
Page 14
14 bow weight adjustment bow weight is one of the most important adjustments of the saw. If the bow weight is not set properly, one can expect poor performance, crooked cuts, tooth stripping, stalling, and the blade popping off the blade wheels. The hydraulic feed rate unit will not compensate for i...
Page 15: Maintenance
15 maintenance before doing maintenance on the machine, disconnect it from the electrical supply by pulling out the plug or switching off the main switch! Failure to comply may cause serious injury. Keep the band saw and the motor clean. If the power cord is worn, cut, or damaged in any way, have it...
Page 16
16 base and bed assembly.
Page 17
17 saw arm assembly – hbs‐916w.
Page 18
18 saw arm assembly – hbs‐1018w.
Page 19
19 parts list for hbs-916w, hbs-1018w index no. Part no. Description size qty 1 .............. Hbs916w-01 ..........Base (s/n 8081108 and lower) ............................................................ 1 ................ Hbs916w-01a ........Base (s/n 8081109 and higher) ............................
Page 20
20 index no. Part no. Description size qty 39 ............ Ts-1490041 ............Hex cap bolt ....................................................M8x25........................ 1 39-1 ......... Ts-1551081 ............Lock washer ....................................................8mm ..................
Page 21
21 index no. Part no. Description size qty ................ Hbs916w-70a ........Electrical panel cover (s/n 8081109 and higher hbs-916w) ................ 1 ................ Hbs1018w-70a ......Electrical panel cover (s/n 808719 and higher hbs-1018w) ................ 1 71 ............ Hbs916w-71 ........
Page 22
22 index no. Part no. Description size qty 100-2 ....... Ts-1551061 ............Lock washer ....................................................M8 ............................. 2 101 .......... Hbs916w-101.........Hose ....................................................................................
Page 23
23 index no. Part no. Description size qty 127-1 ....... Hbs916w-127-1......Eccentric sleeve (inside)(hbs-916w) .................................................. 2 ................ Hbs1018w-127-1 ....Eccentric sleeve (inside)(hbs-1018w) ................................................ 2 128 ..........
Page 24
24 index no. Part no. Description size qty 157 .......... Hbs916w-157.........Blade guard ....................................................................................... 1 ................ Hbs1018w-157a ....Blade guard ............................................................................
Page 25
25 index no. Part no. Description size qty 188 .......... Ts-1524021 ............Set screw ........................................................M8x10........................ 1 189 .......... Hbs916w-189.........Extension bar ...........................................................................
Page 26
26 gear speed reducing box assembly.
Page 27
27 parts list for gear speed reducing box assembly index no. Part no. Description size qty 1 .............. Hbs916w-94-01......Oil seal ............................................................35x55x8 mm............... 1 2 .............. Hbs916w-94-02......Bearing ...................................
Page 28
28 electrical connections – hbs-916w.
Page 29
29 electrical connections – hbs-1018w.
Page 30
30 notes.
Page 31
31.
Page 32
32 walter meier (manufacturing) inc. 427 new sanford road lavergne, tennessee 37086 phone: 800-274-6848 www.Waltermeier.Com.