- DL manuals
- Waring
- Food Processor
- FP40
- Operation Manual
Waring FP40 Operation Manual
Summary of FP40
Page 1
Operation manual for waring fp40 and fp40c food processors fp40c.
Page 2: Important Safeguards
Important safeguards when using electrical appliances, basic safety precautions should always be followed including these: 1. Read all instructions. 2. Blades are sharp. Handle carefully. 3. Your waring food processor is a piece of kitchen equipment and like all other kitchen equipment, extreme care...
Page 3: Grounding Instructions
3 grounding instructions for your protection, this appliance is equipped with a 3-conductor cordset. 120 volt units are supplied with a molded 3-prong grounding-type plug (nema5-15p), and should be used in combination with a properly connected grounding-type outlet as shown in figure a. If a groundi...
Page 4: Introduction
4 introduction the waring ® fp40 and fp40c commercial food processors are the most versatile food processors in their class. These professional machines benefit from waring’s forty years of commercial food service experience as well as thirty years of food processing experience by the same technical...
Page 5: Contents
5 contents important safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 grounding instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 6: The Parts
6 the parts the waring ® fp40 and fp40c food processors are compact, easy-to-use appliances. Completely assembled, the fp40 is only 21" high (53.3cm) and stores conveniently when not in use. For more compact storage, the cover can be stored upside down with the feed tube in the bowl. When stored thi...
Page 7
Batch bowl continuous feed 5a 5a 6 2b fp40 is batch bowl model 2a 12 fp40c is combination model with batch bowl and continuous parts 5b 5b 5c 5c 11 2b 2a 3 10 3 1 1 5 4 7 8 7 9.
Page 8: Assembly of Batch Bowl Parts
8 assembly of batch bowl parts (fp40 & fp40c) we will use the terms work bowl, batch bowl and cutter bowl interchangeably throughout this instruction book. They mean the same thing. • clean and sanitize the motor base, and wash, rinse, and sanitize the bowl, cover, food pusher, food pusher insert an...
Page 9
Batch bowl assembly continued……. • place the cover on the bowl, with the feed tube on the left, slightly toward the front. The locking tabs on the cover should be at the left of the locking tabs on the front rim of the work bowl. • rotate the cover counterclockwise to lock it into place. When the co...
Page 10: (Fp40 & Fp40C)
10 disassembly of batch bowl parts (fp40 & fp40c) always unplug the cord before disassembling • turn the bowl cover clockwise until the safety interlock tab on the cover is disengaged from the magnetic safety interlock switch in the tower, and the tabs are clear of the groove in the tower. The right...
Page 11: Fp40C
11 assembly of continuous feed chute parts fp40c • clean and sanitize the motor base, and wash, rinse, and sanitize the continuous feed chute, cover, slinger disc, food pusher, food pusher insert and processing tools prior to initial use. • place the base on a counter or table near a 3-prong electri...
Page 12: Fp40C
12 two pushers for feed tube pick up the large food pusher and the small food pusher. The large pusher is for processing larger vegeta- bles. The smaller pusher nests in the larger pusher and can be used for smaller vegetables, guiding long thin vegetables for more precise cuts and for jobs like sli...
Page 13: Operating The Controls
13 operating the controls • plug the machine into an electrical outlet. The outlet must be 110/120 volts/60hz. • there are two control paddles (levers) located on the base of the machine. They are on the front and they give you fingertip control of processing. They are large enough to find easily in...
Page 14: Food Preparation
14 food preparation • prepare all food items to be processed by washing and peeling as required. Remove pits, stones, and large seeds. • cut vegetables, meats, cheeses, etc. Into sizes that will fit into your choice of small feed tube or large feed tube for processing with accessory discs, or into s...
Page 15
15 use instructions for s-blade (cutter blade) in the batch bowl fp40 & fp40c • the s-blade (cutter blade) is designed for chopping, grinding, puréeing, blending, mixing, and kneading of ingredients required in almost all recipes. • assemble the bowl and blade as instructed in the section titled “as...
Page 16
16 bread crumbs tear fresh or dried breads and put into the work bowl. After putting the bowl cover in place, press the pulse paddle repeatedly until you reach the consistency desired. For fine powdered bread crumbs, let the food processor run continuously until finished. Grind nuts for cakes put up...
Page 17
17 use instructions for accessory discs in the continuous feed chute fp40 & fp40c • assemble the bowl and accessory disc as instructed in the section titled, “assembly of batch bowl parts,” page 8, or assemble the continuous feed chute and accessory disc as instructed in the section titled “assembly...
Page 18: Slicing Discs
18 accessory disc selection and use the fp40 and fp40c food processor disc accessories are made to perform a large variety of food process- ing tasks: slicing, waved slicing, grating, shredding, french fry and julienne cuts. As of this printing, there are a total of 27 accessory discs available for ...
Page 19: Slicing Operation
19 slicing operation prepare all food items to be processed by washing and peeling as required. Remove pits, stones, and large seeds. Be sure the food will fit into the proper feed chute. Foods such as carrots, cucumbers, etc., should be cut flat at both ends to provide a consistent slice throughout...
Page 20: Grating Operation
20 cfp25 ( 1 ⁄ 64 " fine grate). Use this disc for extra fine grating of hard cheeses like romano and parmesan. Also use this disc for cracker or cookie crumbs or dried bread crumbs. Caution: do not use this disc for soft cheeses or moist breads as this will clog the disc and give poor results. Cfp2...
Page 21: Julienne Discs
21 julienne discs waring size size waring size size item no. Millimeters inches item no. Millimeters inches cfp35 2 mm x 2 mm 5/64" x 5/64" cfp39 6.5 mm x 6.5 mm 1/4" x 1/4" cfp36 2 mm x 4 mm 5/64" x 5/32" cfp40 2 mm x 8 mm 5/64"x 5/16" cfp37 4 mm x 4 mm 5/32"x 5/32" cfp42 8 mm straight ff 5/16" str...
Page 22: Troubleshooting
22 troubleshooting this section describes potential problems and the correct solutions which should be implemented by the user. Problems which cannot be solved with the guidelines listed below should be referred to one of the waring authorized service centers for assistance. A listing of authorized ...
Page 23: Safety Reset Switch
23 safety reset switch the safety reset switch is provided for your convenience and to extend the life of your waring food processor. It is located on the back of your machine, on the safety interlock tower, protected by a round finger hole. The switch button is red. If the machine should become jam...
Page 24: Cleaning
Cleaning clean the food processor and accessories prior to initial use and after each use. Do not use harsh abrasive- type cleaners on any part of the food processor. Cleaning must follow nsf guidelines. Wash the motor shaft with a small brush. Wash, rinse, sanitize and dry the bowl, continuous feed...
Page 25
To clean and sanitize the motor base: clean and sanitize the motor base prior to initial use and after each use. Unplug the unit, then wipe down the exterior surfaces of the motor base with cloths or sponges dampened with a soluble detergent. Next, wipe down with rinse water. Prevent liquid from run...
Page 26: Processing Tools
26 slicing discs waring size size item no. Millimeters inches cfp10 0.8 mm 1 ⁄ 32 " cfp11 2 mm 5 ⁄ 64 " cfp12 3 mm 1 ⁄ 8 " cfp13 4 mm 5 ⁄ 32 " cfp14 5 mm 3 ⁄ 16 " cfp15 6.5 mm 1 ⁄ 4 " cfp16 8 mm 5 ⁄ 16 " cfp17 10 mm 3 ⁄ 8 " cfp18 14 mm 9 ⁄ 16 " waved slicing discs waring size size item no. Millimete...
Page 27: Limited Warranty
27 limited warranty five year limited motor warranty two year limited parts and labor warranty waring commercial warrants that this product's motor shall be free from defects in material and workman- ship for a period of five years from the date of purchase when used with foodstuffs, nonabrasive liq...
Page 28
©2005 314 ella t. Grasso ave. Torrington, ct 06790 www.Waringproducts.Com 05wc30017 ib-3673 any trademarks or service marks of third parties used or referred to herein are the trademarks or service marks of their respective owners..