- DL manuals
- Warmup
- Thermostat
- 5iE
- Installation Manual
Warmup 5iE Installation Manual
Summary of 5iE
Page 1
5ie the smartest smart thermostat installation manual technical helpline 0345 345 2288.
Page 2: Contents
Contents components ..........................................3 safety information ..................................4 step 1 - install boiler receiver ....................7 step 2 - assembling the 5ie ....................... 10 step 3 - paring and testing ....................... 12 step 4 - review ...
Page 3: 5Ie
5ie components power base thermostat face stand boiler receiver power adapter with 1m usb cable pack contents 3.
Page 4: Safety Information
Important information: installation of the boiler receiver should only be carried out by a qualified electrician. It requires a permanent 230v supply. The boiler receiver should be connected to the central heating fused spur or circuit breaker in accordance with current wiring regulations such that ...
Page 5: The Bottom of The Boiler
Before making any permanent fixtures warmup recommends progressing through to ‘step 3 - paring and testing’ upon identifying preferred locations for the boiler receiver and power base. This will ensure the wireless connection is not subject to range or interference issues once installed. The boiler ...
Page 6: Wiring Connections
Wiring connections 5ie step 1 - install boiler receiver 6 note: for alternative installation configurations, see online at www.Warmupsmart.Com/installation 1 2 3 4.
Page 7: Boiler Receiver Will Flash
Once the boiler receiver has been wired correctly, reattach the front panel to the back plate and tighten both screws to secure. Restore power to the boiler. The led on the boiler receiver will flash red slowly to indicate it has power and is not paired. Test the manual control function (page 8) to ...
Page 8: Led Colour
Led colour led status meaning n/a not lit paired green lit constantly relay on red flashing slowly not paired red flashing quickly relay off red lit constantly communication lost relay on led status 5ie step 1 - install boiler receiver led 8.
Page 9: Receiver Be Interrupted.
The warmup 5ie has been designed to still provide heating control should communication between the power base and boiler receiver be interrupted. With the power base and boiler receiver paired and the thermostat face calling for heat, the relay will be activated and the boiler receiver will show a c...
Page 10: Remove The 5Ie From Its
Remove the 5ie from its packaging. Loosen both closing screws located at the bottom of the thermostat face, and remove from the power base. Clip the power base onto the stand. Thread the usb cable through the stand and connect to the power base. Connect the power adaptor to a wall socket. For optima...
Page 11: 5Ie
5ie step 2 - assembling the 5ie remove the 5ie from its packaging. Loosen both closing screws located at the bottom of the thermostat face, and remove from the power base. Drill a hole through the wall to feed the usb cable into the pattress. Connect the usb cable to the power base and attach it to ...
Page 12: Address Setup
When using multiple 5ie’s, each power base should be set to a unique address to prevent interference. Use the dip switches on the power base to select the unique address for each 5ie. Address setup dip switches 5ie step 3 - pairing and testing 12 1 100000 2 010000 3 110000 4 001000 5 101000 6 011000...
Page 13: Paring
Before pairing, please make sure the power base and boiler receiver are powered. If the led on the boiler receiver is not slowly flashing red, indicating that it is ready to be paired, reset its pairing by pressing and holding the power button for 6 seconds. Paring 5ie step 3 - paring and testing 13...
Page 14: Boiler Receiver
Boiler receiver the boiler receiver should now be positioned and mounted within a close vicinity of the boiler. In a position pre-defined by testing the range and functionality of the thermostat and power base. Power base the power base should now be either mounted on the stand or on a wall and pair...
Page 15: Myheating Features Include:
Tick when completed: position boiler receiver install boiler receiver assemble unit (for stand or wall mount) set addresses on power base (multiple units only) pair the power base and boiler receiver test thermostat so the hard work is nearly over. All that remains is to register and setup your devi...
Page 16: Getting Started
Depending on who has installed your 5ie, you will have one of the following screens visible. If you have anything other than the below screens, please press the standby button briefly on the underside of thermostat face. Getting started language if you have this screen present, the thermostat has no...
Page 17: App Download
App download the myheating app is available for ios and android devices via the app store or google play. If you have not done so already, download the myheating app to your tablet or smartphone. Search ‘myheating by warmup’ device number when first registering and setting up your location on myheat...
Page 18: Registration
Below shows the menu structure to follow, when first registering with my.Warmup.Com or the myheating app registration 5ie step 7 - registering your device location a location needs to be setup before a room can be configured and the 5ie device registered. Creating a location is user friendly and eas...
Page 19: 5Ie
Ok, so you are now all set up and ready to go! Have you tested your wireless heating control yet? The 5ie will take approximately two weeks of learning your routines before it can set a customer schedule just for you. So at the moment, adjust the temperature as required, once the 5ie knows your rout...
Page 20: 5Ie
5ie step 9 - troubleshooting troubleshooting due to the large number of different boiler systems and wiring plans in use, warmup cannot guarantee compatibility with a particular system. Compatible systems include combi and system boilers with 230vac, volt-free or low voltage input up to 3a. The boil...
Page 21: 5Ie
5ie technical specifications technical specifications dimensions 86 x 86 x 26.5mm power supply 230v ac, 50hz ip rating ip40 maximum relay load 3a, 250v operational temperature range 0°c - 50°c operational humidity range fuse t1.6a, 250v dimensions (assembled with thermostat) 120 x 121.4 x 72.5mm pow...
Page 22: Contact Us
Contact us uk 0345 345 2288 702 & 704 tudor estate abbey road park royal london nw10 7uw warranty warmup plc warrants this product, to be free from defects in the workmanship or materials, under normal use and service, for a period of three (3) years from the date of purchase by the consumer. If at ...