Warwick CCL 210 ND 8 Owner's Manual - Llii
9
EE
NN
GG
LLII
SS
HH
CC
CC
LL
NN
DD
FRONT PANEL CONTROLS
(CCL ND 8 - CCL 210 ND 8)
IIN
NP
PU
UT
T
socket to plug in a bass guitar.
G
GA
AIIN
N
control + CLIP / LIMIT LED to adjust the input level.
L
LIIM
MIIT
TE
ER
R
switch + 2-colored CLIP / LIMIT LED to compress the signal within the preamp.
L
LO
OW
W B
BO
OO
OS
ST
T
switch + LED to boost the low end.
B
BA
AS
SS
S
control to boost / cut low frequencies.
P
PU
UN
NC
CH
H
control for boosting/cutting deep mids.
M
MIID
D F
FR
RE
EQ
Q.
control to determine the midrange frequency.
M
MIID
D L
LE
EV
VE
EL
L
control to boost / cut the frequency adjusted with the MID FREQ. control.
A
AT
TT
TA
AC
CK
K
control for boosting/cutting high mids.
T
TR
RE
EB
BL
LE
E
control to boost / cut high frequencies.
H
HIIG
GH
H B
BO
OO
OS
ST
T
switch + LED to boost the highs.
M
MU
UT
TE
E
switch + ON / MUTE LED mutes the signal of all outputs except the PHONES and TUNER socket. To avoid
switching noise use the MUTE switch only while no audio signal is being played back.
M
MA
AS
ST
TE
ER
R
control determines the main volume level.
P
PH
HO
ON
NE
ES
S
socket for connecting headphones (min 200 Ohm).
REAR PANEL
(CCL ND 8 - CCL 210 ND 8)
M
MA
AIIN
NS
S IIN
N A
AC
C
terminal with integrated fuse compartment for connecting the amplifier to mains.
P
PO
OW
WE
ER
R
switch for turning the amplifier on and off.
G
GR
RO
OU
UN
ND
DL
LIIF
FT
T
switch disconnects the protective ground line from signal ground. A humming loop may occur when
several devices are hooked up to the same protective ground line and connected by line cables. Use
GROUNDLIFT to eliminate humming loops.
T
TU
UN
NE
ER
R O
OU
UT
T
to connect to a tuner, active when MUTE is enabled.
L
LIIN
NE
E O
OU
UT
T
socket allows connecting additional power amplifiers or active cabinets.
E
EF
FF
F. L
LO
OO
OP
P
for the insertion of an effects unit. Connect EFF. SEND with the input and EFF. RETURN with the output
of the effects device.
D
DII P
PR
RE
E // P
PO
OS
ST
T
switch to route the signal to
D
DII O
OU
UT
T
socket PRE (pressed, direct signal from the bass) or POST (released, signal affected by equalizer or
effects loop). Symmetric XLR out to connect to e.g. a mixing console.
S
SU
UB
BS
SO
ON
NIIC
C
switch to cut low frequencies from the power amp (CCL ND: signals below 120 Hz).
S
SP
PE
EA
AK
KE
ER
R O
OU
UT
T E
EX
XT
T.
to connect an additional speaker with min 8 Ohm.
S
SP
PE
EA
AK
KE
ER
R O
OU
UT
T
to connect the amplifier to the speaker.
H
HO
OR
RN
N A
AT
TT
T.
to control horn volume separately.
Retractable handle and wheels make it easy to transport your Warwick Combo.