Summary of 1.3 XVI series
Page 1
User manuals for xvi series bir and irbf cameras 140217.
Page 2: Table Of Contents
I table of contents 1 general introduction .................................................................................................................. 1 1.1 overview ........................................................................................................................ 1 1.2 ...
Page 3: Welcome
Ii welcome thank you for purchasing our xvi camera! This user ’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user ’s manual well for future reference!.
Page 4
Iii important safeguards and warnings 1 ．electrical safety all installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the selv (safety extra low voltage) and the limited power source is rated 12v dc in the iec60950-1. We as...
Page 5
Iv before installation, please open the package and check all the components are included. Contact your local retailer asap if something is broken in your package. 7. Daily maintenance please shut down the device and then unplug the power cable before you begin daily maintenance work. Use the dry so...
Page 6
1 1general introduction 1.1overview this series megapixel hd camera conforms to the xvi standard. It supports video signal high-speed long distance transmission without any delay. It can be controlled by the dvr conforming to the xvi. 1.2features high-performance cmos image sensor, megapixel defin...
Page 7
2 1.4specifications model parameter 1.3 and 2.1 megapixel xvi ir waterproof camera series 1.3 xvi series 2.1 xvi series video processor 1/3" 2 megapixel cmos video format pal/ntsc effective pixel 1280 (h) *720 (v) 1920 (h) *1080 (v) min illumination 0.05lux@（f1.2，agc on），0 lux with ir electronic shu...
Page 8
3 power consumption 4.5w max (input: 12v @ 0.38a) dimension(mm) irbf bir 94.0 × 98.0 65.0 × 154.7 weight irbf bir 350g 380g installation mode wall mount / ceiling mount.
Page 9
4 2framework and dimensions 2.1irbf series please refer to the following figures for dimension information. The unit is mm. See figure 2-1 and figure 2-2. Figure 2-1 figure 2-2 please refer to the following sheet for detailed information..
Page 10
5 2.2irbf series please refer to the following figures for dimension information. The unit is mm. Sn name function 1 power input port connect to the dc 12v power to input the power. 2 video output port bnc port is to output xvi/cvbs video signal. You can connect to the devices such as the dvr or the...
Page 11
6 3installation 3.1irbf series important please make sure the installation surface can min support the 3x weight of the camera and the bracket. The dome camera usually uses the ceiling installation. It can be installed on the ceiling or the wall. Step1 device installation take the wrench from the ac...
Page 12
7 step 3 adjust monitor angle turn the pan base to the pedestal and secure firmly. Adjust rotate base and the dome body to get the lens to the proper monitor angle. See figure 3-3. Figure 3-3 step 4 fix monitor angle to prevent the dome from moving, use wrench to secure the three set screws to secur...
Page 13
8 step 2 first prepare the cable according to the cable. Line up the three screw holes at the bottom of the bracket to the three installation holes in the wall or the ceiling, and then insert three screws to the three holes of the chassis of the bracket and fix them firmly. Now secure the bracket on...
Page 14
9 4menu 4.1xvi series dvr settings note the following operation and interfaces for reference only. Please refer to the xvi series dvr user’s manual for detailed information. After connected the camera to the xvi series dvr, from main menu->setting->system->ptz, you need to set control mode as hdcvi ...
Page 15
10 4.2menu list the 1 st the 2nd the 3 rd exposure exposure mode auto low noise gain max 0～100 gain min 0～100 return&exit for the 2 nd and the 3 rd menu, when you click exit button to exit, system saves current setup by default. Low motion blur shutter max pal: 0ms～40ms ntsc: 0ms～33ms shutter min pa...
Page 16
11 the 1 st the 2nd the 3 rd flip off/on return&exit motion detect off on area sel 0～3 there are four motion detect zones ranging from 0 to 3. You need to set parameters for each zone. Area state off/on sensitivity 0～100 threshold 0～100 area setup position size use direction buttons to set position ...
Page 17
12 4.3note parameter function brightness it is to adjust monitor window bright. The value ranges from 0 to 100. The default value is 50. The larger the number is, the bright the video is. When you input the value here, the bright section and the dark section of the video will be adjusted accordingly...
Page 18
13 appendix toxic or hazardous materials or elements component name toxic or hazardous materials or elements pb hg cd cr vi pbb pbde circuit board component ○ ○ ○ ○ ○ ○ device construction material ○ ○ ○ ○ ○ ○ wire and cable ○ ○ ○ ○ ○ ○ packing components ○ ○ ○ ○ ○ ○ accessories ○ ○ ○ ○ ○ ○ o: indic...