Watec WAT-910HX Operation Manuals
Danger
Danger
Danger
Multi Function
/
Super High Sensitivity
WAT-910HX
Operation Manual
This Operation Manual covers safety, camera functions, installation and
the correct operating procedure for the WAT-910HX. First, we ask you
to read this Operation Manual thoroughly, then install and operate the
WAT-910HX as advised. In addition, for future reference, we also
advise safekeeping of this manual.
Please contact the distributor or dealer from which the WAT-910HX was
purchased, if you do not understand the installation, operation or safety
instructions laid out in this manual. Not understanding the contents of
the Operation Manual sufficiently may cause damage to the camera.
Guide to the Safety Symbols
The definitions of the symbols used in this operation manual are:
When you do not adhere to or take notice of the “Danger”
sign, it may lead to a serious accident such as death or
injury caused by fire or electric shock.
When you do not adhere to or take notice of the “Warning”
sign, it may cause severe damage such as a physical injury.
When you do not adhere to or take notice of the “Caution”
sign, it may incur injury and cause damage to peripheral
objects in the immediate surroundings.
Cautions for Safety
The WAT-910HX is designed to be used safely; however, if not used
safely, it may lead to a physical accident caused by fire and electric
shock. Therefore, please keep and read the “Cautions for safety” below
for protection against accidents.
•
Do not disassemble and/or modify the WAT-910HX.
•
Do not operate the WAT-910HX with wet hands.
•
Use a stabilized power adaptor designed for DC+12V±
10%, with a current capacity of more than 250mA for
the WAT-910HX.
The recommended voltage is DC+12V±10%
•
Do not expose the WAT-910HX to wetness or high
moisture conditions.
The WAT-910HX is designed and approved for indoor use
only. The WAT-910HX is not water-resistant or waterproof.
If the location of the camera is outdoors or in an outdoor
like environment, we recommend that you use an outdoor
camera housing.
•
Protect the WAT-910HX from condensation.
Keep the WAT-910HX dry at all times during storage and
operation.
•
Should the camera not work properly, switch off the power
immediately. Then check the camera according to the
“Problems and Trouble shooting” section.
•
Avoid the striking of hard objects or dropping the
WAT-910HX.
The WAT-910HX uses high quality electrical parts and
precision components.
•
Do not connect any power supply directly to the video
out terminal of the unit.
Do not connect the WAT-910HX with any monitor using a
video/power single transmission terminal. The WAT-
910HX is not designed for use with this type of
equipment. We also advise you to read the operation
manual of the monitor you plan to use before any
connections are made.
•
Do not install the WAT-910HX in a position subject to
direct sunlight.
Sunlight shinning directly onto the WAT-910HX lens can
cause damage to the CCD.
•
Select a stable place for installation of the WAT-910HX.
Use a support of durable strength around an installation
position on a ceiling or wall when a camera stand or tripod
is used.
•
Do not move the WAT-910HX with the cables
connected.
Before moving the WAT-910HX, always remove the video
cable and power cable from the rear of the camera first.
•
Avoid using the WAT-910HX near any strong electro-
magnetic field.
After installing into main equipment, if the WAT-910HX is
exposed to electromagnetic waves causing the monitored
image to become distorted, we recommend the camera be
shielded by appropriate protective casing.
Problems and Trouble Shooting
If any of the following problems occur when using the WAT-910HX,
•
An optimal picture cannot be obtained, after checking that all the
cables and connections are correctly in place
•
Smoke or any unusual odor emerges from the WAT-910HX
•
An object becomes embedded or a quantity of liquid seeps into the
camera housing
•
More than the recommended voltage or/and amperage has been
applied to the WAT-910HX by mistake
•
Anything unusual occurring to any equipment connected to the
WAT-910HX
Disconnect the camera immediately according to the following
procedures:
①
Switch off the main power supply to the camera.
②
Remove the power and video cables connected to the WAT-910HX.
③
Contact the distributor or dealer from which the WAT-910HX was
purchased.
About EMC
The WAT-910HX is in conformity with EMC test standards carried out
by authorized organizations in Japan.
E
I
A FCC Part15 class B
CCIR
EN61000-6-3/EN50130-4
※
Please use an auxiliary power supply (eg: UPS) to this camera to comply
with EN50130-4 of EMC standards.
Do not modify the WAT-910HX. A modified camera may
not conform to EMC test standards.
Contents
Using the contents figures below, check to make sure all parts are
present before use.
Lens Mount Cap WAT-910HX
DC Plug Iris Connector
Description of Parts
①
IMAGE SENSOR FRONT FACE
・
The light receiving face of the image sensor
(Dirt, water or oil deposits on the image sensor will cause an unclear
picture on the monitor. Attach the lens cap to protect the lens and the
CCD from contamination and damage.)
②
LENS MOUNT
・
Mount for the lens (CS-mount)
③
IRIS LEVEL VOLUME
・
By controlling the volume, the iris level of the DC iris lens can be
adjusted.
④
FINE FOCUS ADJUSTMENT SCREWS
・
There are 3 hex. adjustment screws each placed at intervals of 120゜
for fine focusing of the lens.
⑤
AUTO-IRIS SOCKET
・
This socket is for the video/DC auto-iris lens cable connector.
(Video/DC: Auto selected by the camera)
⑥
TRIPOD MOUNTING SCREW HOLES
・
Mounting holes for stands. The size of these threads are 1/4”, 20
threads, 4.5±0.2mm, which is the same as any standard camera
tripod (U1/4”).
⑦
VIDEO OUT (BNC)
・
The terminal for composite video signal output
⑧
OSD(On Screen Display) OPERATION DIAL
・
The jog-dial for setting the functions on the screen.
⑨
I/O CONNECTOR
・
The control terminal for the Motion Detection.
⑩
POWER IN
・
The terminal designed for connection with the DC-plug of the power
adaptor.
Power Supply
Use a stabilized power adaptor designed for DC+12V±10%, with a
current capacity of more than 250mA. Use the optional DC plug if the
shape or polarity of the DC plug of the power adaptor to be used is not
compatible with the camera (See the drawing on the right below).
The wiring of the connector must be exact.
Be careful not to touch the other terminal while
wiring. Protect the wiring portion by using insulation
tape after wiring. If the above care and attention is
not adhered to, damage to the WAT-910HX and
power adaptor may occur and may also cause fire.
Auto-iris Lens
Before connecting the auto-iris lens, please make sure that the pin
configuration is correct by confirming with the following table. If the
configuration of your iris connector is different from the following, the
plug and pins will need to be rewired.
Pin No.
EIAJ Video
Auto-iris Lens
Arrangement
EIAJ DC
Auto-iris Lens
Arrangement
①
Power
Control －
②
Not used
Control ＋
③
Iris signals
Drive ＋
④
Common (GND)
Drive －
Set-up and Operation
1) Ensure that the power to the WAT-910HX and the peripheral
equipment is turned off before making any connections.
2) Remove the lens mount cap from the WAT-910HX and attach the
CS-mount lens. Use the optional C-mount adaptor (30CMA-R) when
a C-mount lens is used.
3) Connect the iris control cable to ⑤AUTO-IRIS SOCKET on the
WAT-910HX when an auto-iris lens is being used.
4) Connect ⑦VIDEO OUT on the WAT-910HX with the monitor, using
a coaxial cable with 75Ω impedance, such as an RG-59 or an
RG-6/U.
※
Select a monitor with the same television system as the WAT-
910HX EIA or CCIR. A monitor with more than 600TV lines is
recommended.
5) Insert the power plug of the power adaptor into ⑩POWER IN on the
back panel of the WAT-910HX. Confirm that the power adaptor is not
connected to the power supply before insertion of the power plug
into ⑩POWER IN.
6) Turn on the power to the WAT-910HX, monitor and all other allied
equipment. When a picture cannot be obtained on the monitor, or a
problem occurs, check and follow the procedure mentioned in the
【
Problems and Trouble Shooting】section.
7) After following the procedure below and the picture is still out of
focus, open the iris fully and loosen ④FINE FOCUSING
ADJUSTMENT SCREWS with the hex. wrench and move the lens
forwards until a clear picture is obtained.
Manual Lens
Adjust the focus and iris to the best
position on the lens.
Video Auto-iris Lens Adjust the focus on the lens.
DC Auto-iris Lens
Adjust the iris level on the camera, then
adjust the focus on the lens. See below.
Iris Level Adjustment (for DC auto-iris lenses only)
Adjust ③IRIS LEVEL VOLUME placed on the side
of the unit until an acceptable light level is attained.
No change will occur if a video iris lens or manual
iris lens is fitted.
※
When an auto iris lens is used, set SHUTTER to 1/60 (1/50), set
SENS UP to OFF and set AGC to OFF by ⑧OSD OPERATION
DIAL. Then adjust ③IRIS LEVEL VOLUME until an acceptable
light level is attained.
Warning
LEVEL
CLOSED
OPEN
DC+12V
COMMON(GND)
Caution
Warning
Caution
①
②
③
④
Warning
Caution
Hex. Wrench
Cable (300mm)