Water Co Admiral Installation & Operation Manual - Warranty Limitations:

Manual is about: Robotic POOL Cleaner

Summary of Admiral

  • Page 1

    This equipment must be installed and serviced by a qualified technician. Improper installation may result in property damage, serious injury or death. Improper installation and/or operation will void the warranty. Notice to installer this manual contains important information about the installation,...

  • Page 2: Table Of Contents

    Table of contents safety information 2-3 general instructions 3 installation 4 rcd operation 4 removing cleaner from pool 5 cleaning filter bags 5-6 power cord maintenance 6-7 congratulations congratulations and thank you for choosing our admiral pool cleaner the most technologically advanced automa...

  • Page 3: General Instructions

    5. The operating safety of the admiral is only guaranteed if the installation and operation instructions are correctly followed. 6. In the event of defective operation or fault, contact waterco or its nearest authorised service agent. 7. To reduce the risk of injury, do not permit children to use th...

  • Page 4: Installation

    Installation n ensure power supply (transformer) is in the off position. N plug the power supply lead into its own dedicated 220-240v, 50hz ac electrical outlet. It is essential the power point is properly connected to an earth leakage circuit breaker and properly earthed to ground. Consult a qualif...

  • Page 5

    Removing the cleaner from the pool n slowly pull the admiral’s power cord to retrieve the cleaner to the water surface and pool edge. (do not pull the cleaner out of the pool by the power cord). N reach down and grasp the handle of the admiral and remove it from the pool as shown in fig 1 and fig 2....

  • Page 6: Power Cord Maintenance

    N to reattach the filter bag to the bottom lid, turn the filter bag right-side-out. N start at the back of the filter bag and bottom lid where the filter bag says “warning: push bag behind bottom lid tab” and insert the filter bead into the channel, so that the tabs are holding the filter bag in nea...

  • Page 7: Storing The Power Cord

    The following five points can prevent or greatly reduce the tangling of the power cord: 1) make sure there are no objects in the pool during the cleaning cycle for the power cord to get caught on (pool ropes, toys, etc). 2) only allow enough power cord in the pool for full coverage/do not put excess...

  • Page 8: General Maintenance Guide

    General maintenance guide to ensure the maximum life of the admiral robotic pool cleaner, please follow the procedures below: 1. Clean the admiral robotic pool cleaner filter bag after every use. 2. Maintain a correct chemical balance of your pool/spa water. The chemical balance of water is a relati...

  • Page 9: Please Read

    Please read 1. These terms and conditions carefully, as failure to comply may affect your legal rights under this warranty; and 2. Any operation instructions carefully before commencing use of any product manufactured/distributed by waterco limited (“waterco”). Waterco manufactures quality pool and ...

  • Page 10: Exclusions

    Exclusions this warranty does not cover, and waterco will not be responsible for, any defect or damage caused or contributed to by: (a) installation or use of the product other than in accordance with waterco’s written instructions, any statutory requirements and these terms and conditions; (b) use ...

  • Page 11: Warranty Limitations:

    Warranty limitations: the provisions of this warranty are not transferable from the original purchaser and are in addition to and not in modification of or subtraction from any applicable statutory warranties, rights or remedies. Labour is covered by this warranty for a period of 2 years from the da...

  • Page 12

    Symptom possible reasons potential solution dead in water/will not restart is time being allowed for the unit to reset? At least 1 minute is needed between cycles to reset the power supply. Turn power supply off and allow 30 seconds for cleaner to reset. Is the outlet working? Earth leakage circuit ...

  • Page 13: E Sh

    Tr ou bl e sh oot ing symptom possible reasons potential solution dead in water/will not restart is time being allowed for the unit to reset? At least 1 minute is needed between cycles to reset the power supply. Turn power supply off and allow 30 seconds for cleaner to reset. Is the outlet working? ...

  • Page 14: Notes

    Notes 14.

  • Page 15: Notes

    Notes 15.

  • Page 16: Www.Waterco.Com

    New zealand 7 industry road, penrose, 1061 auckland, new zealand tel: + 64 9 525 7570 usa 1864 tobacco rd augusta, ga 30906, usa tel: + 1 706 793 7291 canada 2645, jacques-cartier east boulevard longueuil, québec canada, j4n 1l7 tel: + 450 796 1421 china no.132 buling road, yonghe district, getdd gu...