1. DL manuals
  2. Water Doctors
  3. Water Filtration Systems
  4. AQUA-LOGIC 0.75
  5. Installation Manual

Water Doctors AQUA-LOGIC 0.75 Installation Manual

Manual is about: WATER SOFTENER SYSTEMS

Summary of AQUA-LOGIC 0.75

  • Page 1

    Installation manual water softener systems water doctors water co. A division of hmi water specialists 8201 old central ave. Ne minneapolis, mn 55432 office 952-928-3737 fax 763-535-1805 www.Waterdrs.Com models aqua-logic 0.75, aqua-logic 1.00, aqua-logic 1.50, aqua-logic 2.00

  • Page 2: Water Softener

    Water softener page 2 of 18 table of contents important safety information – read all ...................................................................................... 3 instructions before using ......................................................................................................

  • Page 3: Water Softener

    Water softener page 3 of 18 important safety information – read all instructions before using before beginning installation, read these instructions completely. Then obtain all the materials and tools needed for installation. Note: failure to install the water doctors system correctly voids the warr...

  • Page 4: Water Softener

    Water softener page 4 of 18 softener anatomy figure 1 1…………… valve 2…………… bypass 3…………… resin tank 4…………… distributor 5…………… resin 6…………… salt/brine tank lid 7…………… salt/brinetank 8…………… faceplate/controls not shown brine valve assembly 8 1 3 4 5 6 2 7.

  • Page 5: Water Softener

    Water softener page 5 of 18 specifications feedwater ! Do not use this system on water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. ! Minimum inlet pressure: 20 psig maximum outlet pressure: 125 psig minimum water temperature: 34 de...

  • Page 6: Water Softener

    Water softener page 6 of 18 setup unpacking and inspection check the water doctorssystem components for damage or missing parts. Where to install the softener consider the following points when determining where to install the water softener:  place the water doctorssystem as close as possible to a...

  • Page 7: Water Softener

    Water softener page 7 of 18 installation 1. Turn off gas or electric supply to the water heater. 2. Turn off the water supply to pipes to be cut and drain the house water pipes. 3. Open both hot and cold faucets. 4. Move the softener assembly into installation position.  be sure the installation su...

  • Page 8: Water Softener

    Water softener page 8 of 18 8. Connect and route the valve drain hose.  use the provided drain hose to attach to the valve drain fitting. To keep water pressure from blowing the hose off, use a hose clamp to secure. 9. Locate the other end of the hose at a suitable drain.  tie or wire the hose in ...

  • Page 9: Water Softener

    Water softener page 9 of 18 use step 10 to install rigid drain pipe. 10. To adapt a rigid drain pipe to the water doctorssystem, do not attach barbed hose fitting to valve. Instead, plumb rigid tubing directly to the 1/2" male npt drain fitting. 11. Take the other half of the cut hose and attach it ...

  • Page 10: Water Softener

    Water softener page 10 of 18 20. Turn on the gas or electric supply to the water heater. 21. Remove the brine tank cover and add salt into the tank. Use pellet or coarse solar salt with a purity of 99.5% or higher. Do not use granular, and ice cream-making salts, or salt with iron removing additives...

  • Page 11: Water Softener

    Water softener page 11 of 18 control start-up procedures control start-up, flushing/conditioning and programming procedures may be found in the control service manual included with your system. Model aqua-logic 0.75 (0.75 ft 3 resin) – rated drain flow during regeneration – 1.7 gpm aqua-logic 1.00 (...

  • Page 12: Water Softener

    Water softener page 12 of 18 service cleaning iron out of the water softening system the water doctorssystem is designed to remove minerals like calcium and magnesium from household water. Water doctorsrecommends periodic resin bed cleaning if your iron rating is high. Clean the bed at least every s...

  • Page 13: Water Softener

    Water softener page 13 of 18 troubleshooting 1. Softener fails to regenerate. A. Electrical service to unit has been interrupted. A. Assure permanent electrical service (check fuse, plug, pull chain or switch). B. Timer programming bad (improper programming). B. Check programming and reset as needed...

  • Page 14: Water Softener

    Water softener page 14 of 18 7. Excessive water in brine tank. A. Plugged drain line flow control. A. Clean flow control. B. Brine valve failure. B. Clean brine valve. C. Improper programming. C. Check programming and reset as needed. 8. Salt water in service line. A. Plugged injector system. A. Cle...

  • Page 15: Water Softener

    Water softener page 15 of 18 water softener system parts list figure 5.

  • Page 16: Water Softener

    Water softener page 16 of 18 item no. Part no. Description 2 ch19211-1 brine tank 3 ch15013-2 4" brine well 4 varies by size tank w/ base 5 60795-00 distributor assembly 6 60014/60002-34 2310 safety brine valve assembly/air check 7 ch16371-60 3/8” brine line tube 11 10329 fitting, tube, .375 nut, br...

  • Page 17: Water Softener

    Water softener page 17 of 18 tested and certified by the wqa against nsf/ansi standard 44 & 372 & csa b483.1.

  • Page 18

    Br43398 rev b 1/06/14.