Waterco Admiral Ultra Installation Operation User Manual

Manual is about: Robotic pool scrubber cleaner

Summary of Admiral Ultra

  • Page 1

    This equipment is to be installed and serviced by a qualified technician. Improper installation may result in property damage, serious injury or death. Improper installation and/or operation will void the warranty. Notice to installer this manual contains important information about the installation...

  • Page 2: Table Of Contents

    Table of contents safety information 2-3 general instructions 3 installation 4 removing cleaner from pool 5 cleaning filter bags 5-6 blue cord maintenance 6-7 congratulations congratulations and thank you for choosing our waterco admiral ultra robotic pool cleaner the most technologically advanced a...

  • Page 3: General Instructions

    6. In the event of defective operation or fault, contact waterco or its nearest authorised service agent. 7. To reduce the risk of injury, do not permit children to use this product. 8. Incorrectly installed equipment may fail, causing severe injury or property damage. 9. Chemical spills and fumes c...

  • Page 4: Installation

    Installation n ensure power supply (transformer) is in the off position. N plug the power transformer lead into its own dedicated 220-240v, 50hz ac electrical outlet. It is essential the power point is properly connected to an earth leakage circuit breaker and properly earthed to ground. Consult a q...

  • Page 5

    Removing the cleaner from the pool n slowly pull the admiral ultra’s blue power cord to retrieve the cleaner to the water surface and pool edge. (do not pull the cleaner out of the pool by the blue power cord). N reach down and grasp the handle of the admiral ultra and remove it from the pool as sho...

  • Page 6: Blue Power Cord Maintenance

    N to reinstall the admiral ultra filter bag, first place cleaner bottom lid facing up wards. N place the admiral ultra’s filter bag outer frame onto the cleaner bottom lid and ensure the filter bag frame seats fully into the retaining channels. Note: visually ensure the admiral ultra’s filter bag is...

  • Page 7

    The following five points can prevent or greatly reduce the tangling of the blue power cord: 1) make sure there are no objects in the pool during the cleaning cycle for the blue power cord to get caught on (pool ropes, toys, etc). 2) only allow enough blue power cord in the pool for full coverage/do...

  • Page 8: General Maintenance Guide

    General maintenance guide to ensure the maximum life of the admiral ultra, please follow the procedures below: 1. Clean the admiral ultra’s filter bag after every use. 2. Maintain a correct chemical balance of your pool/spa water. The chemical balance of water is a relationship between its ph, total...

  • Page 9: Warranty Cover

    Please read 1. These terms and conditions carefully, as failure to comply may affect your legal rights under this warranty; and 2. Any operation instructions carefully before commencing use of any product manufactured by waterco limited (“waterco”). Warranty cover if a defect occurs in any waterco p...

  • Page 10: Exclusions

    Exclusions this warranty does not cover, and waterco will not be responsible for, any defect or damage caused or contributed to by: (a) installation or use of the product other than in accordance with waterco’s written instructions, any statutory requirements and these terms and conditions; (b) use ...

  • Page 11: Note:

    Warranty limitations: the provisions of this warranty are not transferable from the original purchaser and are in addition to and not in modification of or subtraction from any applicable statutory warranties, rights or remedies. Labour is covered by this warranty for a period of 1 year from the dat...

  • Page 12

    Symptom possible reasons potential solution cleaner dead in water/will not restart is time being allowed for the unit to reset? At least 30 second are needed between cycles to reset the power supply. Turn power supply off and allow 30 seconds for cleaner to reset. Is the outlet working? Earth leakag...

  • Page 13: Ble Sh

    Symptom possible reasons potential solution cleaner dead in water/will not restart is time being allowed for the unit to reset? At least 30 second are needed between cycles to reset the power supply. Turn power supply off and allow 30 seconds for cleaner to reset. Is the outlet working? Earth leakag...

  • Page 14: Notes

    14 notes.

  • Page 15: Notes

    15 notes.

  • Page 16: Offices - Australia

    Offices - australia abn 62 002 070 733 offices - international new south wales (head office) 36 south street, rydalmere nsw 2116 tel: + 61 2 9898 8600 queensland 77 nealdon drive, meadowbrook qld 4131 tel: + 61 7 3299 9999 victoria unit 1, 6 samantha court, knoxfield vic 3180 tel: + 61 3 9764 1211 w...