Waterco HEAT PUMP SWIMMING POOL HEATERS Owner's Manual

Manual is about: HEAT PUMP SWIMMING POOL HEATERS

Summary of HEAT PUMP SWIMMING POOL HEATERS

  • Page 1

    Waterco limited abn 62 002 070 733 offices - australia nsw - sydney (head office) tel : +61 2 9898 8686 vic/ tas - melbourne tel : +61 3 9879 5141 wa - perth tel : +61 8 9273 1900 qld - brisbane tel : +61 7 3299 9900 sa/ nt - adelaide tel : +61 8 8244 6000 act distributor tel : +61 2 6280 6476 offic...

  • Page 2

    Table of a note to you thank you for buying our waterco heat pump pool heater a heat pump pool heater is a highly efficient, cost effective method of pool heating. Intelligent operation and care will result in many years of enjoyment and pleasure. The waterco heat pump pool heater is a self containe...

  • Page 3

    General safety instructions record your model’s information whenever you call to request service for your heater, you need to know your model number and serial number. You can find this information on the base of your heater. Please also record the purchase date of your appliance and your dealer’s n...

  • Page 4

    Do not deprive heater of water flow for more than 24 hours without draining it. Make sure you leave the bypass valves open as shown in figure 1. At the beginning of each season you must properly balance your water according to the standards prescribed on the previous page before circulating water in...

  • Page 5

    I pg 07 heat pump swimming pool heaters installation instructions location the location of the pool heater is very important in keeping installation costs to a minimum, while providing for maximum efficiency of operation as well as allowing adequate service and maintenance access. The unit is design...

  • Page 6

    I pg 09 heat pump swimming pool heaters flow check valve this is concerned with the installation of heat pumps below the pool water level. The heat pump operates on a pressure switch that activates the unit when the pool pump is switched on. If the heat pump is installed more than 1.5 metres below t...

  • Page 7

    I pg 11 heat pump swimming pool heaters bonding because all metals have different electrical potentials, all metal and electrical components of the pool system must be bonded together. This includes the metal framework of the pool, the light, the pump, the filter (if metal), the heater, any automati...

  • Page 8

    I pg 13 heat pump swimming pool heaters to start-up the unit when the unit is turned on or after a power shut down, the panel lights up and either indicates off or the temperature of the pool water circulating inside the heater. Program in the desired pool water temperature. Once programmed the fan ...

  • Page 9

    I pg 15 heat pump swimming pool heaters winterising set the water temperature setting to off . Turn the pool heater breaker off. If the unit is stored in a place where the temperature drops below the freezing point of 0˚c, it is mandatory that the water accumulated in the unit be drained completely ...

  • Page 10

    I pg 17 heat pump swimming pool heaters there is water around the unit while your watero pool heater is in the heating mode, a large quantity of warm and humid air passes over the evaporator and causes condensation. It is normal to see condensation dripping under the heater. To verify that the water...

  • Page 11

    Fault possible cause action the heat pump does not run the heat pump is not on. Turn on the unit, verify that the circuit breaker is on. The heat pump shuts off less than two minutes after start up the heat pump fan is not running. If the compressor is running, then the reply may be faulty, the fan ...

  • Page 12

    Electrical diagrams instruction on electrical connection of the manual model. Heat pump troubleshooting focus temp international will not pay for a. Service calls to: 1. Inspect and /or correct the installation of your pool heater. 2. Instruct you on how to use your pool heater. 3. Replace house fus...