Waterco R120 Installation - Operation - Warranty Manual

Manual is about: Robotic POOL SCRUBBER Clean

Summary of R120

  • Page 1

    This equipment is to be installed and serviced by a qualified technician. Improper installation may result in property damage, serious injury or death. Improper installation and/or operation will void the warranty. Notice to installer this manual contains important information about the installation...

  • Page 2: Table Of Contents

    Table of contents safety information 2-3 general instructions 3 installation 4 rcd operation 4 removing cleaner from pool 5-6 cleaning filter bags 5-6 power cord maintenance 6-7 congratulations congratulations and thank you for choosing our waterco r120 robotic pool cleaner the most technologically ...

  • Page 3: General Instructions

    7. To reduce the risk of injury, do not permit children to use this product. 8. Incorrectly installed equipment may fail, causing severe injury or property damage. 9. Chemical spills and fumes can weaken the r120. Corrosion can cause the cleaner and other equipment to fail, resulting in severe injur...

  • Page 4: Installation

    Installation n ensure power supply (transformer) is in the off position. N plug the power supply lead into its own dedicated 220-240v, 50hz ac electrical outlet. It is essential the power point is properly connected to an earth leakage circuit breaker and properly earthed to ground. Consult a qualif...

  • Page 5

    Important note: during normal operation, the r120 may appear to shut off for a few seconds. This is a normal part of the pool cleaning program. The cleaner has multiple ways of cleaning the pool walls. It may climb to the top of the pool wall, scrub, then make a turn and drive back down the pool wal...

  • Page 6

    N once the r120’s bottom lid is seated press it firmly into the cleaner, the two red side tabs should click into place and turn the front and rear red retaining clips as indicated by the directional arrows into the locked position, refer figure 9. Gently pull on the cleaner bottom lid to insure that...

  • Page 7: Power Cord Maintenance

    Power cord maintenance in the course of using your r120, the power cord may become twisted or tangled. The r120 power kink resistant cord advantage the r120 robotic pool cleaner has a specifically designed power kink resistant cord using a one piece extruded technology that prevents the cord from de...

  • Page 8: Storing The Power Cord

    Storing the power cord 1. Unplug the power cord from the power supply. 2. Hold the power cord close to the cleaner. Refer figure a. 3. Make a roughly half metre (two feet) loop with the power cord as shown. Refer figure b. 4. When making loops, roll the power cord slightly in a counter clockwise man...

  • Page 9: Please Read

    This warranty does not include replacements of the filter bag, bottom lid, brushes and tracks. Caution: some pool vinyl liners are more susceptible to surface wear and pattern removal than others, caused by objects such as brushes, toys, floats, chlorine dispensers, and automatic pool cleaners comin...

  • Page 10: Exclusions

    E. That has been regularly treated with a sanitising system using bromine, chlorine in one of its compound forms, or generated in-situ, in concentrations (doses) recommended by the relative state or territory health departments. (in areas outside of australia please refer to the local health departm...

  • Page 11: Note:

    Warranty limitations: the provisions of this warranty are not transferable from the original purchaser and are in addition to and not in modification of or subtraction from any applicable statutory warranties, rights or remedies. Labour is covered by this warranty for a period of 1 year from the dat...

  • Page 12

    Symptom possible reasons potential solution cleaner dead in water/will not restart is time being allowed for the unit to reset? At least 1 minute is needed between cycles to reset the power supply. Turn power supply off and allow 30 seconds for cleaner to reset. Is the outlet working? Earth leakage ...

  • Page 13: Ble Sh

    Symptom possible reasons potential solution cleaner dead in water/will not restart is time being allowed for the unit to reset? At least 1 minute is needed between cycles to reset the power supply. Turn power supply off and allow 30 seconds for cleaner to reset. Is the outlet working? Earth leakage ...

  • Page 14: Notes

    14 notes.

  • Page 15: Notes

    15 notes.

  • Page 16: Www.Waterco.Com

    New zealand 7 industry road, penrose, 1061 auckland, new zealand tel: + 64 9 525 7570 usa 1864 tobacco rd augusta, ga 30906, usa tel: + 1 706 793 7291 canada 2645, jacques-cartier east boulevard longueuil, québec canada, j4n 1l7 tel: + 450 796 1421 china no.132 buling road, yonghe district, getdd gu...