1. DL manuals
  2. WaterGroup
  3. Water Filtration Systems
  4. Aqua Flo
  5. Installation, Operation And Instruction Manual

WaterGroup Aqua Flo Installation, Operation And Instruction Manual

Manual is about: reverse osmosis drinking water system

Summary of Aqua Flo

  • Page 1

    Reverse osmosis drinking water system installation, operation and service manual.

  • Page 3

    Important warning - please read system flushing: this reverse osmosis system contains a preservative solution to prevent microbiological growth and freezing which if ingested may cause irritation of the gastrointestinal tract, colic, diarrhea or other symptoms. Therefore, approximately 5 gallons of ...

  • Page 4

    Table of contents introduction ............................................................................................................................................1 product specifications & application guidelines ..................................................................................

  • Page 5

    1 introduction congratulations, on the purchase of your new reverse osmosis drinking water system. Treated with care and regular maintenance, your new system will provide many years of service delivering purified water to the tap. By now, you have probably already opened the box to survey the conten...

  • Page 6

    2 application guidelines (1) nominal product water ratings are based on the following conditions: supply tds of 250 ppm softened tap water, 50 psi (0.36 mpa), 77 o f (25 o c), ph 8 and 15% recovery with outlet to atmosphere. (2) rejection percentages are dependent on the supply conditions and the su...

  • Page 7

    3 supplied item checklist out of the box, your new r.O. System should be supplied with the following items. If any items appear to be missing, please contact the distributor who sold the system. 1. Pressure tank 2. Reverse osmosis system, complete with tubing bundle 3. Reverse osmosis membrane eleme...

  • Page 8

    4 collet body tube o-ring installation all state/provincial and local government codes regarding installation of these devices must be observed. Verify water supply is potable the water supply must meet provincial/state and/or national standards for potable drinking water. Water samples should be se...

  • Page 9

    5 installation of feed water assembly the system comes supplied with a saddle-type valve with mounting hardware and is intended to be used on 3/8" to 1/2" copper tubing cold water supply line. Note: it is not to be used on flex lines. A. Turn off cold water valve under the sink or main valve for the...

  • Page 10

    6 note: some state or local codes may require that the drain saddle be served by a trap other than the one serving the garbage disposal. Before making a connection as shown in figure 6, please check with code authorities. Figure 6 - drain saddle assembly figure 7 - recommended drain saddle connectio...

  • Page 11

    7 installation of ball valve assembly the ball valve and quick connect adapter must be installed on the ro storage tank. A. Put 2-3 wraps of teflon tape on the storage tank threads, and on the ¼" x 3/8" male connector. B. Install the ¼" x 3/8" male connector onto the ball valve. Tighten the fitting ...

  • Page 12

    8 installation of spigot see separate installation instructions for spigot installation of membrane important: keep the membrane and your hands clean in order to avoid bacterial contamination of the membrane. 1. Disconnect the hose on the end of the membrane housing end cap. 2. Unscrew the end-cap. ...

  • Page 13

    9 start-up procedure warning: to prevent microbiological growth and freezing, this reverse osmosis system contains a preservative solution which, if ingested, may cause irritation of the gastrointestinal tract, colic, diarrhea or other similar symptoms. Therefore, 5 gallons (approximately two full t...

  • Page 14

    10 maintenance schedule this schedule is designed for the average potable water supply and should be followed to ensure the proper functioning of your drinking water system. Pre-filter - the pre-filter contains a 5 micron mechanical filter element. Its function is to remove suspended particles from ...

  • Page 15

    11 sanitization procedures for your reverse osmosis system sanitization is a simple but important part of a regular maintenance routine required to keep your reverse osmosis drinking water system operating properly. Recording the dates of all maintenance and sanitization done on the unit is a good i...

  • Page 16

    12 sanitization steps step 1: turn off water supply - close inlet supply needle valve all the way step 2: depressurize system - open faucet supply until all water is emptied use a clean drip pan or basin to continue to catch any spilled water remaining in the housings as you remove the membrane and ...

  • Page 17

    13 step 8: pour the mixed disinfectant solution into the 1st pre-filter sump and re-install. Step 9: open the inlet saddle valve and open the faucet. When water begins running from the faucet again, close the faucet and allow the pressure tank to fill for 5 - 10 minutes. When the pressure tank feels...

  • Page 18

    14 reverse osmosis drinking water system maintenance record installation date: ___________ use this chart to record the dates of any cartridge changes. It is meant to assist you on keeping track of this maintenance. #26084 #26091 #26081 #92015 #92020 #92009,92035,92022 sanitization wtb10 wsw-05b wcb...

  • Page 19

    15 parts list and drawing - model d75tfc-3 note: there may be some parts listed, which are not included with this model. Drawing no............... Description item no. 1...................... Tubing, 3/8" od, poly, blue 87600 2...................... Tubing, 1/4" od, poly, black 115205 3................

  • Page 20

    16 parts list and drawing - models e(24, 50 & 75) tfc-3 note: there may be some parts listed, which are not included with this model. Drawing no............... Description item no. 1...................... Tubing, 3/8" od, poly, blue 87600 2...................... Tubing, 1/4" od, poly, black 115205 3...

  • Page 21

    17 parts list and drawing - model e50tfc-2sf note: there may be some parts listed, which are not included with this model. Drawing no............... Description item no. 1...................... Tubing, 3/8" od, poly, blue 87600 2...................... Tubing, 1/4" od, poly, black 115205 3..............

  • Page 22

    18 reverse osmosis drinking water system flow diagram (all models).

  • Page 23

    19 trouble shooting guide probable cause solutions no water or not enough water 1. Feed water shut off turn on feed water 2. Storage tank valve shut off open tank valve 3. Plugged or crimped lines remove blockage or crimp in lines 4. Pre-filter cartridge clogged replace pre-filter cartridge 5. Low f...

  • Page 24

    20 warranty five year limited warranty: your new drinking system is warranted to the original consumer purchaser, when located at the original installation site, to be free from defects in material and workmanship under normal use within the application guidelines specified by the manufacturer and s...