Vectapure ii™ residential reverse osmosis water system installation and owner’s manual for vectapure ii ™ models ro-4042h, ro-4052h, ro-4152h and all wr2 series reverse osmosis systems this manual is to be left with the owner of the equipment for reference purposes and technical guidance. It is stro...
2 congratulations! You have purchased the finest residential reverse osmosis water system available for your home. It will provide you years of reliable service if properly installed, operated and maintained. Please read this entire manual before attempting installation and operation. Section 1. Fre...
3 q: does reverse osmosis remove bacteria? Cryptosporidium? Viruses? Reverse osmosis membranes will virtually eliminate most chemicals, bacteria, viruses and parasites such as cryptosporidium from the water. Where these conditions exist, pre-filters and other system components located before the mem...
4 q: where is the system installed? Typically, the system is installed under the kitchen sink. Some homeowners or installers prefer the basement or crawlspace, as this conserves storage in the kitchen and may allow for easier access to the system for maintenance purposes. If you install the system m...
5 q: when should the membrane be changed? If you notice gradually decreasing production from your system, differing taste to your drinking water or a white scale forming on pans or dishes, it probably means that your membrane is deteriorating and is losing its effectiveness. You may purchase a pocke...
6 keep in mind that you may install a tube tee on the line to the faucet to connect icemakers or other faucets to the system. If you locate your system farther than 20 feet from the faucet, you will need to use 3/8” tubing or install a pressure booster pump to your line. See your dealer for parts an...
7 step 4. Install the sink faucet tools required for this step: an electric drill, a 5/8 ” carbide bit, a small adjustable wrench, a center punch, a pencil, a rat-tail file. 1. Examine the sink. If it has an existing hole for mounting a faucet, skip to step 4. (6). 2. Locate and mark the spot you wi...
8 2. Position the drain saddle assembly in the selected location and mark the spot through the threaded outlet with a pencil or marker 3. Drill a ¼” hole at the marked spot. Strip the backing paper from the adhesive side of the saddle gasket and position on the inside of the drain saddle, aligning t...
9 at the waste elbow, on the membrane housing. Place the storage tank in the location you have chosen for it. Using the clear 3/8” tube connect the system fitting marked “to tank” to the tank valve. Connect the 3/8’” tube attached to the faucet to the system fitting marked “to faucet”. If the tubing...
10 tighten – 1/4 turn after hand tight is usually sufficient. Repeat with one of the carbon block cartridges in the middle housing (three-housing wr2 units only) and with the other carbon block cartridge in the right hand housing. 5. Remove the membrane element from its wrapping. Disconnect the ¼” t...
11 1. Close the cold water supply valve. Open the faucet and completely drain until the flow of water stops. Remove the filter housings with the housing wrench and discard the old filter cartridges. Thoroughly clean the inside of the housing bowls with soap and water. Rinse completely. If the ro has...
12 to change the membrane element, start by closing the cold water supply valve. Make sure that your hands are washed and your tools are clean. Repeat step 9 (5.) above. If the old membrane element does not pull out easily by hand, use a pair of pliers to gently pull the element by the product tube ...
13 vectapure ii™ and wr2 series residential reverse osmosis systems parts list key description part number comment key description part number comment 1 filter housing - clear he1014cw-u 14 mounting clips wp-225 filter housing - white he1014ww-u 2 cartridge, combo ppcc10-05 all models 16 low pressur...
14 vectapure ii™ residential reverse osmosis system flow layout ro4042h / ro4052h not included on ro4042h.
15 vectapure ii™ residential reverse osmosis system flow layout ro415h.
16 visit the waterite technologies website for information, consumer online replacement parts and product updates at: www.Waterite.Com waterite technologies, inc. 3-75 meridian drive winnipeg, manitoba canada r2r 2v9 (204) 786-1604 (204) 783-1599 fax www.Waterite.Com.
