Summary of WL2000IT
Page 1
Waterlogic 2000it technical manual - issue b, december 2013 wl2000it technical manual.
Page 2
2 3 waterlogic 2000it technical manual - issue b, december 2013 index machine overview 4 wetted parts layout - hot and cold 8 pre delivery inspection procedures (pdi) 9 installation procedures 11 operating instructions 14 maintenance and servicing 16 sanitising or descaling 17 fault finding 18 techn...
Page 3: Machine Overview
4 5 waterlogic 2000it technical manual - issue b, december 2013 5 machine overview wl 2000it cold tank the cold tank is manufactured from 304 stainless steel which is non-corrosive, inert and reflects ultra violet light (uv). The cold water temperature is preset at approximately 5°c by factory, this...
Page 4
6 7 waterlogic 2000it technical manual - issue b, december 2013 water pipes and fittings the inlet and the internal water circuit pipe size is 1/4” and 5/16”. The entire internal water circuit and all the components which come in contact with water are food grade nsf / wras approved. Water valves di...
Page 5: Pre Delivery
8 9 waterlogic 2000it technical manual - issue b, december 2013 pre delivery inspection procedures (pdi) cautions: • only competent trained technicians should work on waterlogic products. • waterlogic units may weigh over 25kg. We recommend caution when lifting. • packing materials could present a t...
Page 6: Installation Procedures
10 11 waterlogic 2000it technical manual - issue b, december 2013 installation procedures 1. Mount the wl 2000it on a firm flat surface with a 50mm air gap on both sides and top so that it cannot topple or fall from a counter top. 2. It is advisable that the water and electricity supply are within t...
Page 7
12 13 waterlogic 2000it technical manual - issue b, december 2013 9. If installing a hot and cold model, do the following, otherwise go to point 10. Select the hot water option and press the dispense button to start flushing water through the machine filter and hot tank. The filter will produce carb...
Page 8: Operating Instructions
14 15 waterlogic 2000it technical manual - issue b, december 2013 dispensing your choice of water is very simple, as follows: 1. Place your cup centrally in the dispensing area 2. Select the type of water you wish to be dispensed and press the corresponding button. 3. Keep the button depressed until...
Page 9: Maintenance And Servicing
16 17 waterlogic 2000it technical manual - issue b, december 2013 maintenance and servicing 6 month service procedure this procedure should only be carried out by persons trained by waterlogic international or their approved distributors. The following instructions cover models that can include hot,...
Page 10
18 19 waterlogic 2000it technical manual - issue b, december 2013 5. Remove the top cover on the mini model and lower panel on the free standing models. 6. Bypass the wl 2000it internal twist filters as no sanitiser should enter the filters. These can be bypassed by using dummy (empty) filters (same...
Page 11: Technical Specifications
20 21 waterlogic 2000it technical manual - issue b, december 2013 technical specifications and warranties safety subject to the standard terms and conditions of sale (a copy of which has been provided to you), neither waterlogic international limited (“waterlogic”), nor any affiliated companies shal...
Page 12: End of Life
22 23 waterlogic 2000it technical manual - issue b, december 2013 end of life non eu countries at the end of this product’s life, please ensure that it is disposed of in an environmentally friendly manner which is in line with your country requirements/ guidelines. Weee (eu only) please be aware tha...
Page 13: Main Pcb Schematic Diagram
24 25 waterlogic 2000it technical manual - issue b, december 2013 main pcb schematic diagram hot and cold.
Page 14: Wetted Parts Illustration
26 27 waterlogic 2000it technical manual - issue b, december 2013 wetted parts illustration wetted parts list 1 3 5 13 n° part description 1 jg bulkhead connector union 1/4" * 1/4" 2 jg lld pe tube - blue o.D.1/4" 3 valved twist filter head 4 carbon gac filter 5 jg lld pe tube - blue o.D.1/4" 6 poly...
Page 15: Main Parts Illustration
28 29 waterlogic 2000it technical manual - issue b, december 2013 main parts illustration freestanding model - hot & cold spare parts numbers 1 2 3 4 5 8 11 12 13 14 15 16 16 17 19 20 21 22 23 25 34 45 35 36 37 38 39 44 40 41 42 43 26 27 28 29 30 31 32 33 24 17 18 9 10 6 7 n° part description 1 wl20...
Page 16
30 31 waterlogic 2000it technical manual - issue b, december 2013 n° part description 28 pcb of wl2000 hc&ca 29 silicon button key mat wl2000 hc 30 wl2000 front hatch panel charcoal with uv logo 31 button label wl2000 hc&ca 32 wl2000 drip tray grill 33 wl2000 drip tray body charcoal 34 fs silver sid...
Page 17: Main Parts Illustration
32 33 waterlogic 2000it technical manual - issue b, december 2013 main parts illustration mini model - cold & ambient spare parts numbers n° part description 1 wl2000 top cover black 2 mini back panel 3 switch - power (red) 4 fuse holder & fuse 5 socket 6 thermostat 7 mini silver side panel (left) 8...
Page 18
34 35 waterlogic 2000it technical manual - issue b, december 2013 n° part description 26 uv lamp fixing rubber 27 uv lamp retaining threaded nut 28 uv lamp 4w 29 o-ring 30 quartz sleeve for 4w lamp 31 power transformer uv 32 wl2000 mini upper base 33 ballast metal cover 34 uv cold tank assembly 2l 3...
Page 19
36 eng0292-02/12/13 wli trading ltd. Suite 4, 2nd floor beacon court, sandyford, dublin 18, ireland www.Waterlogic.Com waterlogic usa, 4141 n. 156th street, omaha, ne 68116 speak to a water expert rest of the world exportsales@waterlogic.Com + 353 1 293 1960 usa, canada and mexico info@waterlogicusa...