Summary of WL4 Firewall
Page 1
Wl4 firewall technical manual.
Page 2
2 waterlogic 4 firewall technical manual - issue a, october 2010 3 index machine overview . 4 mains parts layout - hot, cold and sparkling 8 mains parts layout - hot and cold 9 mains parts layout - cold and sparkling 10 mains parts layout - cold only 11 carbonation tank 12 pre delivery inspection pr...
Page 3: Machine Overview
4 waterlogic 4 firewall technical manual - issue a, october 2010 55 standard cold tank (2 litres) the standard cold tank is manufactured from 304 stainlesssteel which is noncorrosive. The temperature of the cold tank is controlled by a microprocessor and can be set between 3°c and 12°c.We recommend ...
Page 4
6 waterlogic 4 firewall technical manual - issue a, october 2010 7 in faucet uv the unique design allows the faucet area to be steralised before, during and after every dispense. There are two types of sensors available, the cds uv sensor that detects if the uv lamp is working and the uv sensor that...
Page 5: Main Parts Layout
8 waterlogic 4 firewall technical manual - issue a, october 2010 9 main parts layout hot, cold and sparkling main parts layout hot and cold fil ter fil ter in (water) solenoid valve 2 solenoid valve 1 solenoid valve 3 solenoid valve 6 hot water out hot water out w ater in cold water out sparkling wa...
Page 6: Main Parts Layout
10 waterlogic 4 firewall technical manual - issue a, october 2010 11 main parts layout cold and sparkling main parts layout cold only fil ter fil ter in (water) solenoid valve 1 solenoid valve 3 solenoid valve 6 w ater in cold water out sparkling water out solenoid valve 5 solenoid valve 4 pump filt...
Page 7: Pre Delivery
12 waterlogic 4 firewall technical manual - issue a, october 2010 13 pre delivery inspection procedures (pdi) cautions: only competent trained technicians should work on waterlogic products. Waterlogic units may weigh over 25kg. We recommend caution when lifting. Packing materials could present a tr...
Page 8: Installation Procedures
14 waterlogic 4 firewall technical manual - issue a, october 2010 15 1. Remove packing straps and unpack unit and visually inspect for any damage. (report any defects to waterlogic as soon as possible). 2. Place the unit on a suitable work bench. 3. Open the top cover by removing the screws and rele...
Page 9: Instructions
16 17 waterlogic 4 firewall technical manual - issue a, october 2010 lifting the wl4 firewall pressure release valve (yellow), located beside the uv lamp assembly, for approximately 2 seconds. 7. Connect the water supply. All water sources should be potable. Allow the water supply to run clear of an...
Page 10: Operating Instructions
18 waterlogic 4 firewall technical manual - issue a, october 2010 19 installation kit 1-20 metres of 6mm 5/16 inch water pipe, prv (pressure reducing valve) set at 3 bar or 42 psi, non return valve, self-cutting saddle valve or isolating valves, moulded plug fitted, co2gas (if required), co2 regulat...
Page 11: Operating Instructions
20 waterlogic 4 firewall technical manual - issue a, october 2010 21 cold water press the cold water button. Cold water will be dispensed immediately. Ambient water press the ambient water button and water will be dispensed. Sparkling water press the sparkling water button. Sparkling water will be d...
Page 12
22 23 and fill the cold tank with a mix of water and sanitisation fluid. 7. Replace the uv lamp and reconnect the uv loom. Do not touch the uv lamp with your bare hands as this will shorten the lamp life. 8. Machines with the hot option. Remove and inspect the faucet. If the faucet is cracked or has...
Page 13: Malfunction Icons
24 waterlogic 4 firewall technical manual - issue a, october 2010 25 note - if all the icons should flash and an audible alarm sounds, please switch the machine off immediately and call you authorised service agent. 1. No flow of water: ensure that there is a water supply to the wl4 firewall from th...
Page 14: Technical Specifications
26 waterlogic 4 firewall technical manual - issue a, october 2010 27 technical specifications and warranties the tank to defrost, and then flush the cold water system. Check the temperature settings are correct. If the cold tank is not frozen then check the solenoid valve is operating correctly and ...
Page 15: End Of Life
28 waterlogic 4 firewall technical manual - issue a, october 2010 29 end of life non eu countries at the end of this products life, please ensure that it is disposed of in an environmentally friendly manner which is in line with your country requirements/ guidelines. Weee (eu only) please be aware t...
Page 16
30 waterlogic 4 firewall technical manual - issue a, october 2010 31 electrical wiring diagram 230v hot, cold and sparkling mark description mark description 0s1 solenoid valve (for in water) mc motor for compressor 20s2 solenoid valve (for hot water) mfc fan motor for compressor 20s3 solenoid valve...
Page 17
32 waterlogic 4 firewall technical manual - issue a, october 2010 33 electrical wiring diagram 230v cold and sparkling mark description mark description 20s1 solenoid valve (for in water) mfc fan motor for compressor 20s2 solenoid valve (for ambient water) pf power fuse (250v/10a) 20s3 solenoid valv...
Page 18: Wetted Parts Illustration
34 waterlogic 4 firewall technical manual - issue a, october 2010 35 wetted parts illustration hot, cold and sparkling 3 4 5 6 7 8 9 10 11 13 14 48 49 50 17 51 54 32 33 53 31 29 46 28 15 18 19 16 27 26 34 36 35 58 37 38 39 42 23 12 44 45 43 22 47 21 20 30 57 55 56 25 24 41 40 52 2 1 electrical wirin...
Page 19: Wetted Parts List
36 waterlogic 4 firewall technical manual - issue a, october 2010 37 no part no part description 28 pu-4008 jg equal elbow connector 1/4" (pi0308s) 29 pu-4031 jg lld pe tube - blue o.D.1/4" 30 pu-4011 jg equal tee connector 1/4" (pi0208s) 31 pu-4031 jg lld pe tube - blue o.D.1/4" 32 pu-4008 jg equal...
Page 20: Wl4 Main Parts List
38 waterlogic 4 firewall technical manual - issue a, october 2010 39 no part no part description 1 pl-1321 wl-4 top cover safety support 2 pl-1328 wl-4 mini side panel-l 3 st-8260 wl-4 pcb holder bracket 4 en-6059 plastic pcb support 5 en-6117 main pcb wl4000 6 st-8285 wl4 main pcb metal cover 7 en-...
Page 21: Wl4 Main Parts List
40 waterlogic 4 firewall technical manual - issue a, october 2010 41 no part no part description 62 pu4056b double solenoid valve dc24v 1000mm 63 st-8265 wl-4 fan bracket 64 ct-2005 fan motor 230v/50-60hz (ac axial fan) uf12b-23b-wl 65 pl-1336 wl-4 upper panel wire route hole silicon cover 66 st-825...
Page 22: Wl4
42 43 wl400 uts & tap technical manual - issue a, august 2011 wl4 pcb programming procedure the service pcb has been developed to allow the wl4 4 firewall pcb to be reset using an external pcb. Button descriptions up: menu up down: menu down enter: enter and modify select: select and enter/exit read...
Page 23
44 waterlogic 4 firewall technical manual - issue a, october 2010 45 • to view the actual data for cold water temperature, hot water temperature and filter timer, press either the “up” or “down” button. Note: this data is not the wl4 firewall setting information but the wl4 firewall actual current d...
Page 24
46 47 wl400 uts & tap technical manual - issue a, august 2011 step 4: reset pcb setting • press the “select” button and set led will illuminate. The screen will display set work data. Now press the “enter” button and the display will change to the first setting menu set °c/°f: °c or °f”. • to change...
Page 25
Eng0011-24/07/12 speak to a water expert waterlogic usa, 4141 n. 156th street, omaha, ne 68116 usa, canada and mexico info@waterlogicusa.Com + 1 402 884 7212 wli trading ltd. Suite 4, 2nd floor beacon court, sandyford, dublin 18, ireland www.Waterlogic.Com rest of the world exportsales@waterlogic.Co...