Waterproof W1-B User Manual - page 2
1. Packing list
Name
Digital Keypad W1/W3-B
Quantity
Remark
Screw driver
Rubber bungs
Self Tapping Screws
Manager Card
1
4
4
2
6*27mm, used for fixing
3.5*27mm, used for fixing
Manager Add Card & Manager Delete Card
User Manual
1
1
Please ensure that all the above contents are correct. If any are missing please notify
the supplier of the W1/W3-B.
2. Description
3. Features
l
Waterproof, conforms to IP68
l
Strong Zinc Alloy Electroplated anti-vandal case
l
Full programming from the keypad
l
2500 users, supports Card, PIN, Card + PIN
l
Can be used as a stand alone keypad
l
Programmable one relay output
l
Backlight keypad
l
Wiegand 26 input & output
l
Adjustable Door Output time, Alarm time, Door Open time
l
Block enrollment, can enroll maximum 2500 consecutive card within 3 minutes
l
Very low power consumption (60Ma)
l
Fast operating speed, <20ms with 2500 users
l
Easy to install and program
l
Built in light dependent resistor (LDR) for anti tamper
4. Specifications
12~24V AC/DC
2500
12 keys, 2 x 6 digits(W1-B)
12 keys, 3 x 4 digits(W3-B)
EM 125 KHZ car d/ Tag
3~6 cm
<80mA
≤40mA
Max 2A
Max 20A
Operating Humidity
Environment
Adjustable Door Relay time
Adjustable Alarm Time
Wiring Connections
Dimensions
Net Weight
Gross Weight
5%~ 95% RH
Conforms to IP68
0~99 seconds
0~3 minutes
Electric Lock, Exit Button,
DOTL, External Alarm
550 g
700 g
Operating Voltage
User Capacity
Keypad
Card Type
Card Reading Distance
Active Current
Idle Current
Lock Output Load
Alarm Output Load
5. Installation
l
Remove the back cover from the keypad using the supplied security screwdriver
l
Drill 4 holes on the wall for the screws and I hole for the cable
l
Fix the back cover firmly on the wall with 4 flat head screws
l
Thread the cable through the cable hole
l
Attach the keypad to the back cover.
6. Wiring
Colour
Grey
Yellow
Brown
Red
Black
Blue
Purple
Function
D0
Alarm -
OPEN
D-IN
12~24V AC&DC
NO
COM
Description
Wiegand Output D0
White
Wiegand Output D1
Request to Exit Button
Door Contact
12~24V
Power Input
AC&DC
12~24V AC&DC Power Input
Connection Diagram
8. Anti Tamper Ala rm
The W1/W3-B uses a LDR (light dependent resistor) as an anti tamper alarm. If the
keypad is removed from the cover then the tamper alarm will operate.
9. Sound and Light indication
Operation Status
Power on
Operation successful
Operation failed
Enter into programming mode
Red Light
Bright
-
-
-
Bright
Bright
Green Light
-
-
-
Bright
-
-
Blue Light
-
-
-
-
-
-
Buzzer
Short Ring
-
Short Ring
Short Ring
3 Short Ring
Short Ring
-
Short Ring
-
Press keypad
-
-
-
-
Bright
10. W1/W3-B Deta iled Pro gra mming Guide
10.1 User Settings
To exit from the programming mode
To change the master code
Set valid cardonly users
Set valid card and PIN users
Set valid card or PIN users
*
Master code
#
888888 is the default factory master code
To enter the programming mode
*
No te tha t to un de rtake the fol lowi ng pr og rammi ng the mas ter us er mus t be log ge d in
0 New code # New code #
The master code is any 6 digits.
To add a PIN users
1 User ID number # PIN #
The ID number is any number between 1 ~
2500. The PIN is any four digits between 0000
~ 9999 with the exception of 1234 which is
reserved. Users can be added
continuously
without exiting from
programming
mode
as
follows:
1 User ID No 1 # PIN # User ID No 2 # PIN #
Operating Temperature -25~60℃
Alarm Negative
Orange
NC
Pink
GND
Stand by
Setting the working mode:
3 0
#
3 1
#
3 2
# Entry is by either Card or PIN (default)
.2.
1
2
3
4
5
6
7
8
9
0
#
In the programming mode
Exit from the programming mode
Open the door
.4.
.6.
.5.
To Delete a PIN user
To change the PIN of a PIN user
(Note:This step must be done out of
programming mode)
* ID number # Old PIN # New PIN # New PIN #
2 User ID number #
Users can be deleted continuously without
exiting programming mode
7. To Reset to Factory Default
Bright
-
-
Bright
Alarm
.1.
To add a card user (Method 1)
This is a fast way to enter cards
using ID number auto generation.
1 Read Card #
Cards can be added continuously without exiting
programming mode
1 ID number # Card #
To add a card user (Method 2)
T h i s i s t h e s e c o n d w a y t o e n t e r
cards using User ID Allocation.
In this method a User ID is allocated
to a card. Only one user ID can be
allocated to a single card.
l
Built in buzzer
l
Red, Yellow and Green LEDs display the working status
l
12~24V AC/DC
l
Two- year warranty
W1/W3-B is single door multifunction access controller or a Wiegand output keypad or
card reader. It is suitable for mounting either indoor or outdoor in harsh environments. It
is housed in a strong, sturdy and vandal proof Zinc Alloy electroplated case.
The electronics are fully potted so the W1/W3-B is waterproof and conforms to IP68.
The W1/W3-B supports up to 2500 users in either a Card, 4 digit PIN, or a Card + PIN
option. The inbuilt card reader supports EM, 125KHZ frequency card/Tag. The W1/W3-
B has many extra features including block enrollment, wiegand 26 bits interface, and backlit
keypad...etc.
These features make the W1/W3-B an ideal choice for door access not only for small
shops and domestic households but also for commercial and industrial applications
such as factories, warehouses, laboratories, banks and prisons.
Wiegand Interface
Wiegand 26 input & output
PCB connect diagram
Anti-demolition alarm
D
0
D
1
A
L
A
R
M
-
O
P
E
N
D
_
IN
G
N
D
A
C
&
D
C
A
C
&
D
C
N
C
C
O
M
N
O
J1
D
0
D
1
A
L
A
R
M
-
O
P
E
N
D
_
IN
G
N
D
A
C
&
D
C
A
C
&
D
C
N
C
C
O
M
N
O
J1
Green
D1
12~24V AC&DC
Relay NO
Relay COM
Relay NC
W1/W3-B Negative
D0
D1
ALARM-
OPEN
D_IN
AC&DC
12~24V/3A
Exit button
W1/W3-B
Door detecting switch
-
+
Green
White
Grey
Yellow
Brown
Red
Black
Blue
Purple
Orange
Power
Alarm
GND
AC&DC
AC&DC
NC
COM
NO
Pink
-
+
Lock
In
4
0
0
4
Pow er“+”
Electric bo lt:
NC
Electric strike :
NO
Power“+”
Alarm “-”
Common Power Supply
D0
D1
ALARM-
OPEN
D_IN
DC
/3A
12 V
W 1/ W3-B
-
+
Wiegand D0
Wiegand D1
GND
AC&DC
AC&DC
NC
COM
NO
NC
COM NO +12V GND OPEN
Green
White
Grey
Yellow
Brown
Red
Black
Blue
Purple
Orange
Pink
Door detecting switch
Exit button
Alarm
Power
+
-
+
-
Fail-secure lock
Alarm“-”
Special Power Supply
Notes:
Connect the negative pole of the lock to NC is for Fail safe lock.
Connect the negative pole of the lock to NO is for Fail-secure lock.
To reset to factory default, power off, press * , hold it and power on, release it until
hear two beeps and the LED shines in orange, then read any two EM cards, the LED will
turn in red, means reset to factory default setting successfully. Of the two EM cards
read, the first one is Manager Add card, the second one is Manager Delete card.
-
-
-
-
Alarm
Bright
-
-
-
Short Ring
Entry is by Cardonly
Entry is by Card and PIN together
To add and delete users in either card or PIN mode ( 3 2 # ) (Default setting)
Ca rd quantity is betwe en 1~2 500.
Th e 8 digits card numbe r is the last 8 digits on
the card.
Max imum 2500 cards can be enrolled at a stretch
wi thin 3 mi nutes.
To ad d ca rd us er (Met ho d 3)
Add a se ries ca rds us er s
Bl ock Enr ol lment
To delete card user by card
number.
Note Users can be deleted
continuously without exiting
from programming mode.
2 Read Card #
5 ID number # 8 digits Card number # Card quantity #
To delete a card user by user ID.
This option can be used when
a
user has lost their
card
2 User ID #
.3.
Remarks: Reset to factory default, the user's information is still retained.
( W1-B&W3-B are in the same function, only different in shape. )
L135 x W58 x H26 mm(W1-B)
L128 x W82 x H28 mm(W3-B)
W1-B
W3-B