Installation guide and operating manual es-cutp-8 and es-futp-8 enclosed ethernet switches for workgroups or classrooms corporate headquarters manufacturing/customer service 5001 american blvd. W., suite 605 945 37 th avenue, nw bloomington, mn 55437 rochester, mn 55901 phone: 800.441.5319 phone: 80...
Es-cutp and es-futp manual page 1 table of contents 1.0 specifications........................................................................................................................ 2 1.1 technical specifications .................................................................................
Es-cutp and es-futp manual page 2 1.0 specifications 1.1 technical specifications ports performance when a port is operating at 100mbps: data rate: 100mbps when a port is operating at 10mbps: data rate: 10mbps network standards 100mbps: ethernet ieee 802.3u, 100base-tx, 100base-fx 10 mbps: ethernet ...
Es-cutp and es-futp manual page 3 packaging enclosure: rugged high-strength sheet metal. Designed for mounting on wall or on shelf or desk. Can also be set on desk, desk or tabletop. Dimensions: 10.5 x 8.5 x 1.5 in. (26.7 x 21.6 x 3.8 cm) weight: 5.4 lb. (2.45 kg.) cooling method: convection led ind...
Es-cutp and es-futp manual page 4 2.2 product description - general waters’ es family of enclosed switches provides the switching speed and reliability to smoothly support multiple workgroups at 10mbps or 100mbps speed. The optional fiber port is configured and tested in the factory and is available...
Es-cutp and es-futp manual page 5 2.4 fiber port, st or sc connector for the es-futp-8 100mbps fiber port: st sc the fast ethernet fiber switched port on the es-futp-8 is set to operate at fixed 100mbps for guaranteed high performance. The fiber port is factory-built as either a multi-mode st, sc, o...
Es-cutp and es-futp manual page 6 sequence occurs in a small fraction of a second and is transparent to an observer. See section 4.6 for additional details. Another feature implemented in the es switches is a collision-based flow-control mechanism (when operating at half-duplex only). When the switc...
Es-cutp and es-futp manual page 7 example 2. Es-cutp-8 the es-cutp-8 fits very well in a small business, classroom or lab experiencing a need to scale its lan quickly and cost effectively. With its half/full duplex switching capability, the es-cutp-8 provides a very economical high bandwidth solutio...
Es-cutp and es-futp manual page 8 note: it is recommended that high quality cat5 cables (which work for both 10mbps and 100mbps) be used whenever possible in order to provide flexibility in a mixed-speed network, since the es series switch ports are auto-sensing for either 10 and 100mbps. 3.2.1 conn...
Es-cutp and es-futp manual page 9 where p t = transmitter output power, and p r = receiver sensitivity worst case opb = opb - 1db(for led aging) - 1db(for insertion loss) worst case distance = {worst case opb, in db} / [cable loss, in db/km] where the “cable loss” for 62.5/125 and 50/125 µ m (m.M.) ...
Es-cutp and es-futp manual page 10 the switched rj45 ports are full duplex and auto-sensing for speed. (see section 2.2). When the connected device is 10mbps, the switch adheres to all the rules of 10mbps ethernet configurations. The 10mbps users share a 10mbps traffic domain and can “communicate wi...
Es-cutp and es-futp manual page 11 4.5 led’s pwr: illuminates green, steady on when power applied. Error: indicates the self-test at power up was not successful speed: per port, on = 100mbps; off = 10 mbps (when link is made) link/act: per port, steady on for link with no traffic, blinking indicates...
Es-cutp and es-futp manual page 12 4. If the problem is isolated to a network device other than the waters es series product, it is recommended that the problem device be replaced with a known good device. Verify whether or not the problem is corrected. If not, go to step 5 below. If the problem is ...
Es-cutp and es-futp manual page 13 2. Clearly mark the return material authorization (rma) number on the outside of the shipping container. 3. Waters network systems is not responsible for your return shipping charges. 4. Ship the package to: waters network systems 2411 seventh street nw rochester, ...
