1. DL manuals
  2. WaterSoft
  3. Water Dispenser
  4. rs1
  5. Installation And Operation Manual

WaterSoft rs1 Installation And Operation Manual

Manual is about: CABINET Water Softener

Summary of rs1

  • Page 1

    Rs1 rs1 softener manual installation / operation manual cabinet water softener.

  • Page 2

    Rs1 softener specifications.................................................................................................Page 3 softener installation......................................................................................................Page 5 master programming........................

  • Page 3

    Rs1 warning lubricants do not use vaseline, oils, hydrocarbon lubricants or spray silicone anywhere! Petroleum base lubricants will cause swelling of o-rings and seals. The use of other lubricants may attack plastic noryl®. It is recommended that dow corning® silicone grease be used as a lubricant f...

  • Page 4

    Rs1 please note these specifications before proceeding operating pressure range : 20 - 125 psi operating temperature range : 33º f - 120º f inlet / outlet pipe size : 3/4: fnpt please comply with all applicable plumbing codes protect the softener and piping from freezing temperatures please read the...

  • Page 5

    Rs1 -pre-installation check list- a water test should always be performed in order to determine total water hardness (in gpg) and total dis- solved iron (in parts per million - ppm). This is critical for proper equipment selection, sizing and for determining the program for regeneration frequency. I...

  • Page 6

    Rs1 installation -softener location / other requirements- • locate the unit near an unswitched, 120 volt / 60 hz grounded electrical outlet. • check for distance and proper drain installation (e.G. Floor drain, washing machine standpipe). • determine type and size of piping required for softener con...

  • Page 7

    Rs1 -drain line connection- 1. Pull out clip and remove drain line assembly located on the left side of control valve. Remove drain line hose barb and wrap threads with teflon tape. Reinstall drain line hose barb. Caution : hand tighten only!!! Replace drain line assembly and reinstall clip. 2. Inst...

  • Page 8

    Rs1 installation - pressurizing the system - 1. Make certain the rs1 series control valve is in service position. 2. Slowly rotate bypass valve to the service position. (position of bypass lever is parallel to inlet / outlet piping.) 3. Open the nearest faucet to evacuate air from plumbing lines. 4....

  • Page 9

    Rs1 1. Set time of day. 2. Set a.M. Or p.M. 3. Set water hardness in grains per gallon (gpg). Note : if the water contains iron and / or manganese, multiply the total parts per million (ppm) by “four” (4) and then add to the grains per gallon (gpg) of hardness. Use this compensated hardness level wh...

  • Page 10

    Rs1 - start up procedure - - disinfection - for disinfection of your unit, please follow the sani-system procedure on the back of the packet provided. - filling the brine tank with salt - to expect a high level of performance and reliability, a salt manufactured specifically for water softeners must...

  • Page 11

    Rs1 - to skip a regeneration - 1. For vacations or extended periods of absence, the power supply can be disconnected from the control valve. 2. Upon return, plug in cord and reset the time of day. - general care and cleaning - 1. Do not place heavy or sharp objects on water softener or cabinet. 2. U...

  • Page 12

    Rs1 master programming mode master programming mode to enter master programming mode, press and hold both buttons for 5 seconds. Note: all master programming functions have been preset at the factory. Unless a change is desired, it is not necessary to enter master programming mode. 1. Regeneration t...

  • Page 13

    Rs1 master programming mode 5. Reserve capacity setting % example ( p - 25 ) 6. Bluetooth enabled be - 1 (on) be - 0 (off) 7. Bluetooth password bbpp is displayed for one second, then password is displayed. 8. To exit the master programming mode, press the menu/enter button until time of day returns...

  • Page 14

    Rs1 14 utilizing bluetooth control to take advantage of the bluetooth interface this feature must be set up on a bluetooth enabled device. Note: at the time of this release bluetooth control only works on android devices with a compatible version of bluetooth. 1. Download the legacy view app from th...

  • Page 15

    Rs1 15 power head assembly ref description part number qty 1 secondary plate 20016x002 1 2 encoder wheel 20001x007 1 3 encoder board* 20016x200 1 4 main plate 20016x001 1 5 motor* 20016x200 1 6 brine cam 20001x122 1 7 main gear 20001x120 1 6 1 2 7 * 4 * * components included in wiring harness (not s...

  • Page 16

    Rs1 valve body assy. 16 ref # description part # qty. 1 piston assembly 20001x231 1 2 screw 20001x001 2 3 seal & spacer kit 20561x253 1 4 bottom spacer n/a 1 5 dlfc button 2.0 20251x267 1 6 dlfc housing 20251x100 1 7 90 elbow drain line 1 8 dlfc clip 20001x214 1 9 brine valve 20251x225 1 10 blfc ass...

  • Page 17

    Rs1 cabinet body assembly 17 1 2 10 11 12 13 16 3 4 5 6 7 8 9 15 14 17 18 19 20 21 22 23 24 ref # description part # qty. 1 clack windsor tank cabinet bottom 20016x007 1 2 resin / media tank - natural 30935x000 1 3 brine well assy. & air check 20016x008 1 4 cabinet cap 20016x009 1 5 cabinet lid 2001...

  • Page 18

    Rs1 bypass assembly ref # description part # qty 1a meter assembly, turbine complete 20003x200 1 1 plastic bypass valve assembly 20561x292 1 2 bypass valve 3/4” stainless steel 20561x270 1 bypass valve 1” stainless steel 20561x283 1 18 (1a) (1) (2).

  • Page 19

    Rs1 service instructions / instructional videos available at www.Csiwater.Com a. General preliminary instructions perform before all servicing operations 1. Turn off water supply to conditioner. -if the conditioner installation has a “three valve” bypass system, first open the valve in the bypass li...

  • Page 20

    Rs1 service instructions / instructional videos available at www.Csiwater.Com d. To replace brine valve 1 . Follow steps a1 - a3 2. Remove the top cover. Disconnect the meter cable from the meter assembly. 3. Remove screw and washer at piston drive yoke. Remove powerhead mounting screws. The entire ...

  • Page 21

    Rs1 service instructions / instructional videos available at www.Csiwater.Com f. To replace seals and spacers 1. Follow steps a1 - a3 . 2. Remove the control top cover. Disconnect the meter signal wire from the meter. 3. Remove screw and washer at piston drive yoke. Remove powerhead mounting screws....

  • Page 22

    Rs1 troubleshooting guide symptom probable cause correction 1.Softener fails to regenerate automatically power supply plugged into intermittentent or dead power source connect to constant power source disconnected meter cable reconnect cable improper control valve programming reset program settings ...

  • Page 23

    Rs1 symptom probable cause correction 7. Excessive water in brine tank and / or salty water to service plugged drain line or drain line control check flow to drain. Clean drainline flow control button dirty or damaged brine valve clean or replace brine valve. Plugged injector or screen clean or repl...

  • Page 24

    Rs1 watersoft 710 orange st, ashland, oh 44805 l ph 419-281-6829 l fax 419-281-2375 www.Watersoft.Com.