1. DL manuals
  2. Watlow
  3. Fryer
  4. MINICHEF 2000
  5. Application Manual

Watlow MINICHEF 2000 Application Manual

Other manuals for MINICHEF 2000: Application Manual, Application Manual
Manual is about: Deepfat Fryer

Summary of MINICHEF 2000

  • Page 1

    M ini c hef tm 2000 applications 10 - 19 deepfat fryer applications guide wmc2-xagn-0003-rev a may 1997 $5.00 made in the u.S.A. Programming & operating steps 97 registered company winona, minnesota usa iso 9001 total customer satisfaction watlow controls 1241 bundy blvd. P.O. Box 5580 winona, minne...

  • Page 2: Table of Contents

    Table of contents application 10 automatic deepfat fryer with autolift control . . . . 1 application 11 automatic deepfat fryer with autolift control . . . 11 application 12 manual deepfat fryer with autolift control. . . . . 23 application 13 pressurized automatic deepfat fryer . . . . . . . . 35 a...

  • Page 3: Automatic Deepfat Fryer

    Application 10 automatic deepfat fryer with autolift control single heat channel, four menus introduction to application 10 . . . . . . . . . . . . . . 1 configuration mode quick reference . . . . . . . . . 3 program mode quick reference . . . . . . . . . . . . 4 step 7 design a faceplate overlay . ...

  • Page 4

    2 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 0 key functions in configuration mode key functions in operation mode ç warning: the basket up and basket down keys cause or initiate motion. Appropriate reasonable care should be taken to prevent personal injury or machine damage as a r...

  • Page 5

    A p p l i c a t i o n 1 0 wa t l o w m i n i c h e f 2 0 0 0 ■ 3 configuration mode quick reference these are the functions, parameters and values included in the configuration mode for this application. You must select application 10 to access them. For directions, see the hardware & software setup...

  • Page 6: Program Mode Quick Reference

    4 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 0 program mode quick reference these are the functions, parameters and values included in the program mode for this application. You must select application 10 to access them. For menu programming direc- tions, see the hardware & softwar...

  • Page 7

    A p p l i c a t i o n 1 0 wa t l o w m i n i c h e f 2 0 0 0 ■ 5 step 7 design a faceplate overlay to complete the installation, you must apply a graphic membrane to the front panel of the controller. The following artwork will help you design and create a membrane for this application. For more dim...

  • Page 8

    6 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 0 step 8 operate the controller summary of key functions in operation mode key function a menu 1 b menu 2 c basket up d menu 3 e menu 4 f basket down startup apply power to the fryer and add cooking oil if necessary. Initial preheat at p...

  • Page 9

    A p p l i c a t i o n 1 0 wa t l o w m i n i c h e f 2 0 0 0 ■ 7 start/stop key indicator light will flash slowly. The temperature of channel 1 will be displayed until the operating temperature is reached. The heat output indicator light - g, just below the display- will light up whenever the contro...

  • Page 10

    8 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 0 the display. (the message, which varies based on programming at [m`__] / [alarn] will appear for ten seconds.) an audible tone will sound for five seconds. Time will continue to count down on the display. 4. When the cooking cycle is f...

  • Page 11

    A p p l i c a t i o n 1 0 wa t l o w m i n i c h e f 2 0 0 0 ■ 9 lowing will happen, depending on the way the controller was programmed at [etype] / {sound]: with sound set to 0: the controller automatically switches to idle, where the con- troller maintains the temperatures at set point and does no...

  • Page 12

    1 0 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 0 temperature alarms the controller will alert you to temperature alarm conditions if they occur. If an alarm occurs, take action as determined by your supervisor. See the appendix in the hardware & software setup guide for a troublesh...

  • Page 13: Automatic Deepfat Fryer

    A p p l i c a t i o n 1 1 wa t l o w m i n i c h e f 2 0 0 0 ■ 1 1 application 11 automatic deepfat fryer with autolift control single heat channel, 40 menus introduction to application 11 . . . . . . . . . . . . . 11 configuration mode quick reference . . . . . . . . 13 program mode quick reference...

  • Page 14

    1 2 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 1 key functions in configuration mode key functions in operation mode ç warning: the basket up and basket down keys cause or initiate motion. Appropriate reasonable care should be taken to prevent personal injury or machine damage as a...

  • Page 15

    A p p l i c a t i o n 1 1 wa t l o w m i n i c h e f 2 0 0 0 ■ 1 3 configuration mode quick reference these are the functions, parameters and values included in the configuration mode for this application. You must select application 11 to access them. For directions, see the hardware & software set...

  • Page 16: Program Mode Quick Reference

    1 4 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 1 program mode quick reference these are the functions, parameters and values included in the program mode for this application. You must select application 11 to access them. For menu programming directions, see the hardware & softwar...

  • Page 17

    A p p l i c a t i o n 1 1 wa t l o w m i n i c h e f 2 0 0 0 ■ 1 5 step 7 design a faceplate overlay to complete the installation, you must apply a graphic membrane to the front panel of the controller. The following artwork will help you design and create a membrane for this application. For more d...

  • Page 18

    1 6 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 1 step 8 operate the controller summary of key functions in operation mode key operation function a idle temperature number one b idle temperature number two c increment and basket up d menu select e start/stop f decrement and basket d...

  • Page 19

    A p p l i c a t i o n 1 1 wa t l o w m i n i c h e f 2 0 0 0 ■ 1 7 initial preheat at power-up, the unit will preheat to the temperature value set in the configuration mode [etype] / [preht]. The display will show [pre-`] [`heat] followed by oil tem- perature as the oil heats. When the unit reaches ...

  • Page 20

    1 8 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 1 1. Select the menu you want to run as shown earlier in “select a menu”. 2. With [`idle] or time of day on the display, press the start/stop key. If the preheat condition has not been met, the fryer will preheat until [ready] appears ...

  • Page 21

    A p p l i c a t i o n 1 1 wa t l o w m i n i c h e f 2 0 0 0 ■ 1 9 with sound set to 0: the controller automatically switches to idle. [`idle] or cur- rent time will appear on the display. The start/stop key indicator light will flash slowly. The controller will maintain temperature at the programme...

  • Page 22

    2 0 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 1 rent time will appear on the display. The start/stop key indicator light will flash slowly. The controller will maintain temperature at the programmed set point. With sound set to 1, 2, or 3: [``end] will appear on the display and an...

  • Page 23

    A p p l i c a t i o n 1 1 wa t l o w m i n i c h e f 2 0 0 0 ■ 2 1 manual basket lift at any time you can raise or lower the basket manually by using the down-arrow key (to lower) or the up-arrow key (to raise). If you raise the basket manually while cooking, the timer will pause. Countdown time wil...

  • Page 24

    2 2 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 1 errors the controller will alert you to errors if they occur. Errors are critical problems that shut down the unit. If an error occurs, an error message will appear on the display. You should switch off the power and call for service...

  • Page 25: Manual Deepfat Fryer

    A p p l i c a t i o n 1 2 wa t l o w m i n i c h e f 2 0 0 0 ■ 2 3 application 12 manual deepfat fryer with autolift control single heat channel, one menu introduction to application 12 . . . . . . . . . . . . . 23 configuration mode quick reference . . . . . . . . 25 step 7 design a faceplate overl...

  • Page 26

    2 4 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 2 key functions in configuration mode key functions in operation mode ç warning: the basket up and basket down keys cause or initiate motion. Appropriate reasonable care should be taken to prevent personal injury or machine damage as a...

  • Page 27

    A p p l i c a t i o n 1 2 wa t l o w m i n i c h e f 2 0 0 0 ■ 2 5 configuration mode quick reference these are the functions, parameters and values included in the configuration mode for this application. You must select application 12 to access them. For directions, see the hardware & software set...

  • Page 28

    2 6 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 2 auto-tuning note: before auto-tuning application 12, [tenp1] in the operations menu must first be set to a value that is typical of your application. (see the hardware & software setup guide for information on programming menus.) the...

  • Page 29

    A p p l i c a t i o n 1 2 wa t l o w m i n i c h e f 2 0 0 0 ■ 2 7 step 7 design a faceplate overlay to complete the installation, you must apply a graphic membrane to the front panel of the controller. The following artwork will help you design and create a membrane for this application. For more d...

  • Page 30

    2 8 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 2 step 8 operate the controller summary of key functions in operation mode key function a temp b time c increment & basket up d not used e start/stop f decrement & basket down startup apply power to the fryer and add cooking oil if nec...

  • Page 31

    A p p l i c a t i o n 1 2 wa t l o w m i n i c h e f 2 0 0 0 ■ 2 9 five second timeout when using the up or down keys to change a value, if you do not press any key for 5 seconds, the controller will automatically be set to the last value on the display and return to [`idle]. Initial preheat at powe...

  • Page 32

    3 0 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 2 the melt cycle to avoid burning congealed oil (shortening), a slow heating action may be necessary. If this is desired, be sure that in the configuration mode [etype] / [melt] has been set to [```on]. Then, when the oil temperature i...

  • Page 33

    A p p l i c a t i o n 1 2 wa t l o w m i n i c h e f 2 0 0 0 ■ 3 1 with sound set to 1, 2, or 3, [``end] will appear on the display and an audible tone will be emitted. The start/stop indicator light will flash rapidly. You can acknowl- edge and silence the tone by pressing the start/stop key or it ...

  • Page 34

    3 2 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 2 5. To repeat cooking, repeat steps 1 through 5. Adjust a menu while cooking you can adjust the temperature and time settings during the cooking and hold sequences by performing the actions shown under “set the menu” earlier in this s...

  • Page 35

    A p p l i c a t i o n 1 2 wa t l o w m i n i c h e f 2 0 0 0 ■ 3 3 & software setup guide for a troubleshooting chart and a summary of temperature alarms. Errors the controller will alert you to errors if they occur. Errors are critical problems that shut down the unit. If an error occurs, an error ...

  • Page 36: Notes

    3 4 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 2 notes.

  • Page 37: Pressurized Automatic

    A p p l i c a t i o n 1 3 wa t l o w m i n i c h e f 2 0 0 0 ■ 3 5 application 13 pressurized automatic deepfat fryer single heat channel, six menus introduction to application 13 . . . . . . . . . . . . . 35 configuration mode quick reference . . . . . . . . 37 program mode quick reference . . . . ...

  • Page 38

    3 6 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 3 key functions in configuration mode key functions in operation mode summary of input/output functions note: for details, see wiring instructions in the hardware & software setup guide. Input 1 fryer temperature → input 2 not used → e...

  • Page 39

    A p p l i c a t i o n 1 3 wa t l o w m i n i c h e f 2 0 0 0 ■ 3 7 configuration mode quick reference these are the functions, parameters and values included in the configuration mode for this application. You must select application 13 to access them. For directions, see the hardware & software set...

  • Page 40: Program Mode Quick Reference

    3 8 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 3 program mode quick reference these are the functions, parameters and values included in the program mode for this application. You must select application 13 to access them. For menu programming directions, see the hardware & softwar...

  • Page 41

    A p p l i c a t i o n 1 3 wa t l o w m i n i c h e f 2 0 0 0 ■ 3 9 step 7 design a faceplate overlay to complete the installation, you must apply a graphic membrane to the front panel of the controller. The following artwork will help you design and create a membrane for this application. For more d...

  • Page 42

    4 0 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 3 step 8 operate the controller summary of key functions in operation mode key function a menu 1 b menu 2 c menu 3 d menu 4 e menu 5 f menu 6 startup 1. Apply power to the fryer and add cooking oil if necessary. Initial preheat at powe...

  • Page 43

    A p p l i c a t i o n 1 3 wa t l o w m i n i c h e f 2 0 0 0 ■ 4 1 the heat output indicator light - g, just below the display- will light up whenever the controller is calling for heat. When the fryer is at operating temperature (above relative set point minus the ready band) [ready] will appear on...

  • Page 44

    4 2 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 3 the way the controller was programmed at [etype] / [sound]: with sound set to 0: the controller automatically switches to [`idle], where the controller maintains the temperatures at set point and does not run time. [`idle] or current...

  • Page 45

    A p p l i c a t i o n 1 3 wa t l o w m i n i c h e f 2 0 0 0 ■ 4 3 flashes slowly. With sound set to 1, 2, or 3: [``end] will appear on the display and an audible tone will be emitted. The menu key indicator light will flash rapidly. You can acknowl- edge and silence the tone by pressing the active ...

  • Page 46: Notes

    4 4 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 3 notes.

  • Page 47: Pressurized Automatic

    A p p l i c a t i o n 1 4 wa t l o w m i n i c h e f 2 0 0 0 ■ 4 5 application 14 pressurized automatic deepfat fryer one heat channel, 40 menus introduction to application 14 . . . . . . . . . . . . . 45 configuration mode quick reference . . . . . . . . 47 program mode quick reference . . . . . . ...

  • Page 48

    4 6 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 4 key functions in configuration mode key functions in operation mode summary of input/output functions note: for details, see wiring instructions in the hardware & software setup guide. Heat 1 idle 1 temp 2 idle 2 time 4 5 start/ stop...

  • Page 49

    A p p l i c a t i o n 1 4 wa t l o w m i n i c h e f 2 0 0 0 ■ 4 7 configuration mode quick reference these are the functions, parameters and values included in the configuration mode for this application. You must select application 14 to access them. For directions, see the hardware & software set...

  • Page 50: Program Mode Quick Reference

    4 8 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 4 program mode quick reference these are the functions, parameters and values included in the program mode for this application. You must select application 14 to access them. For menu programming directions, see the hardware & softwar...

  • Page 51

    A p p l i c a t i o n 1 4 wa t l o w m i n i c h e f 2 0 0 0 ■ 4 9 step 7 design a faceplate overlay to complete the installation, you must apply a graphic membrane to the front panel of the controller. The following artwork will help you design and create a membrane for this application. For more d...

  • Page 52

    5 0 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 4 step 8 operate the controller summary of key functions in operation mode key function a idle one temperature b idle two temperature c increment d menu select e start/stop f decrement start-up apply power to the fryer and add cooking ...

  • Page 53

    A p p l i c a t i o n 1 4 wa t l o w m i n i c h e f 2 0 0 0 ■ 5 1 when the unit reaches initial preheat temperature, [ready] will flash once on the dis- play and an audible tone will sound for 2 seconds. Then [`idle] will appear on the dis- play. (if the real-time clock option is installed and [set...

  • Page 54

    5 2 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 4 if the preheat condition has not been met, the fryer will preheat until [ready] appears on the display. If the fryer is at operating temperature [ready] will immediately appear on the display. 3. With [ready] on the display, place th...

  • Page 55

    A p p l i c a t i o n 1 4 wa t l o w m i n i c h e f 2 0 0 0 ■ 5 3 run a menu (without preheat feature) this procedure describes how to run a menu when the preheat function is inactive — in other words, when the [ready] parameter in the [setup] function of the configuration mode is set to [```no] — ...

  • Page 56

    5 4 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 4 event outputs event output 1 assists in controlling pressure. Event output 1 will switch on when a menu starts and switch off when the time remain- ing is equal to the value programmed in the configuration mode under [etype] / [ptine...

  • Page 57: Pressurized Manual

    A p p l i c a t i o n 1 5 wa t l o w m i n i c h e f 2 0 0 0 ■ 5 5 application 15 pressurized manual deepfat fryer one heat channel introduction to application 15 . . . . . . . . . . . . . 55 configuration mode quick reference . . . . . . . . 57 step 7 design a faceplate overlay . . . . . . . . . . ...

  • Page 58

    5 6 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 5 key functions in configuration mode key functions in operation mode summary of input/output functions note: for details, see wiring instructions in the hardware & software setup guide. Heat 1 temp 2 time 4 5 start/ stop 6 down your c...

  • Page 59

    A p p l i c a t i o n 1 5 wa t l o w m i n i c h e f 2 0 0 0 ■ 5 7 configuration mode quick reference these are the functions, parameters and values included in the configuration mode for this application. You must select application 15 to access them. For directions, see the hardware & software set...

  • Page 60

    5 8 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 5 auto-tuning note: before auto-tuning application 15, [tenp1] in the operations menu must first be set to a value that is typical of your application. (see hardware & software setup guide for information on programming menus.) then se...

  • Page 61

    A p p l i c a t i o n 1 5 wa t l o w m i n i c h e f 2 0 0 0 ■ 5 9 step 7 design a faceplate overlay to complete the installation, you must apply a graphic membrane to the front panel of the controller. The following artwork will help you design and create a membrane for this application. For more d...

  • Page 62

    6 0 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 5 step 8 operate the controller summary of key functions in operation mode key function a temp b time c increment d not used e start/stop f decrement startup apply power to the fryer and add cooking oil if necessary. Set the menu set t...

  • Page 63

    A p p l i c a t i o n 1 5 wa t l o w m i n i c h e f 2 0 0 0 ■ 6 1 five second timeout when using the up or down keys to change a value, if you do not press any key for 5 seconds, the controller will automatically be set to the last value on the display and return to [`idle]. Initial preheat at powe...

  • Page 64

    6 2 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 5 the melt cycle to avoid burning congealed oil (shortening), a slow heating action may be necessary. If this is desired, be sure that in the configuration mode [etype] / [melt] has been set to [```on. Then, when the oil temperature is...

  • Page 65

    A p p l i c a t i o n 1 5 wa t l o w m i n i c h e f 2 0 0 0 ■ 6 3 run a menu (without preheat feature) this procedure describes how to run a menu when the preheat function is inactive — in other words, when the [ready] parameter in the [setup] function of the configuration mode is set to [```no] — ...

  • Page 66

    6 4 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 5 cancel a menu canceling the menu stops controller operation completely. The controller does not main- tain set point temperatures or run time. Users may cancel the menu in order to run another one, to stop menu operation for any reas...

  • Page 67: Automatic Deepfat Fryer

    A p p l i c a t i o n 1 6 wa t l o w m i n i c h e f 2 0 0 0 ■ 6 5 application 16 automatic deepfat fryer one heat channel, six menus introduction to application 16 . . . . . . . . . . . . . 65 configuration mode quick reference . . . . . . . . 67 program mode quick reference . . . . . . . . . . . ....

  • Page 68

    6 6 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 6 key functions in configuration mode key functions in operation mode summary of input/output functions note: for details, see wiring instructions in the hardware & software setup guide. Input 1 fryer temperature → input 2 not used → e...

  • Page 69

    A p p l i c a t i o n 1 6 wa t l o w m i n i c h e f 2 0 0 0 ■ 6 7 configuration mode quick reference these are the functions, parameters and values included in the configuration mode for this application. You must select application 16 to access them. For directions, see the hardware & software set...

  • Page 70: Program Mode Quick Reference

    6 8 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 6 program mode quick reference these are the functions, parameters and values included in the program mode for this application. You must select application 16 to access them. For menu programming directions, see the hardware & softwar...

  • Page 71

    A p p l i c a t i o n 1 6 wa t l o w m i n i c h e f 2 0 0 0 ■ 6 9 step 7 design a faceplate overlay to complete the installation, you must apply a graphic membrane to the front panel of the controller. The following artwork will help you design and create a membrane for this application. For more d...

  • Page 72

    7 0 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 6 step 8 operate the controller summary of key functions in operation mode key function a menu 1 b menu 2 c menu 3 d menu 4 e menu 5 f menu 6 startup apply power to the fryer and add cooking oil if necessary. Initial preheat at power-u...

  • Page 73

    A p p l i c a t i o n 1 6 wa t l o w m i n i c h e f 2 0 0 0 ■ 7 1 the word [pre-`] [`heat] will appear on the display for a few moments. The menu key indicator light will flash slowly. The temperature of channel 1 will then be displayed until the operating temperature is reached. The heat output in...

  • Page 74

    7 2 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 6 the display. (the message, which varies based on programming at [m```] / [alarn] will appear for ten seconds.) an audible tone will sound for five seconds. Time will continue to count down on the display. 4. When the cooking cycle is...

  • Page 75

    A p p l i c a t i o n 1 6 wa t l o w m i n i c h e f 2 0 0 0 ■ 7 3 the way the controller was programmed at [etype] / {sound]: with sound set to 0: the controller automatically switches to idle, where the con- troller maintains the temperatures at set point and does not run time. [`idle] or time of ...

  • Page 76: Notes

    7 4 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 6 notes.

  • Page 77: Automatic Deepfat Fryer

    A p p l i c a t i o n 1 7 wa t l o w m i n i c h e f 2 0 0 0 ■ 7 5 application 17 automatic deepfat fryer one heat channel, four menus introduction to application 17 . . . . . . . . . . . . . 75 configuration mode quick reference . . . . . . . . 77 program mode quick reference . . . . . . . . . . . ...

  • Page 78

    7 6 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 7 key functions in configuration mode key functions in operation mode summary of input/output functions note: for details, see wiring instructions in the hardware & software setup guide. Input 1 fryer temperature → input 2 not used → e...

  • Page 79

    A p p l i c a t i o n 1 7 wa t l o w m i n i c h e f 2 0 0 0 ■ 7 7 configuration mode quick reference these are the functions, parameters and values included in the configuration mode for this application. You must select application 17 to access them. For directions, see the hardware & software set...

  • Page 80: Program Mode Quick Reference

    7 8 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 7 program mode quick reference these are the functions, parameters and values included in the program mode for this application. You must select application 17 to access them. For menu programming directions, see the hardware & softwar...

  • Page 81

    A p p l i c a t i o n 1 7 wa t l o w m i n i c h e f 2 0 0 0 ■ 7 9 step 7 design a faceplate overlay to complete the installation, you must apply a graphic membrane to the front panel of the controller. The following artwork will help you design and create a membrane for this application. For more d...

  • Page 82

    8 0 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 7 step 8 operate the controller summary of key functions in operation mode key function a menu 1 b not used c menu 2 d menu 3 e not used f menu 4 startup apply power to the fryer and add cooking oil if necessary. Initial preheat at pow...

  • Page 83

    A p p l i c a t i o n 1 7 wa t l o w m i n i c h e f 2 0 0 0 ■ 8 1 if the fryer is not at operating temperature, it will preheat. Meanwhile: the word [pre-`] [`heat] will appear on the display for a few moments. The menu key indicator light will flash slowly. The temperature of channel 1 will be dis...

  • Page 84

    8 2 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 7 with sound set to 4 or 5, [``end] will appear on the display and the menu key indicator light will flash rapidly. You must acknowledge the audible tone by pressing the active menu key. Once acknowledged, the tone is silenced and the ...

  • Page 85: Automatic Deepfat Fryer

    A p p l i c a t i o n 1 8 wa t l o w m i n i c h e f 2 0 0 0 ■ 8 3 application 18 automatic deepfat fryer one heat channel, 40 menus introduction to application 18 . . . . . . . . . . . . . 83 configuration mode quick reference . . . . . . . . 85 program mode quick reference . . . . . . . . . . . . ...

  • Page 86

    8 4 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 8 key functions in configuration mode key functions in operation mode summary of input/output functions note: for details, see wiring instructions in the hardware & software setup guide. Heat 1 idle 1 temp 2 idle 2 time 4 5 start/ stop...

  • Page 87

    A p p l i c a t i o n 1 8 wa t l o w m i n i c h e f 2 0 0 0 ■ 8 5 configuration mode quick reference these are the functions, parameters and values included in the configuration mode for this application. You must select application 18 to access them. For directions, see the hardware & software set...

  • Page 88: Program Mode Quick Reference

    8 6 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 8 program mode quick reference these are the functions, parameters and values included in the program mode for this application. You must select application 18 to access them. For menu programming directions, see the hardware & softwar...

  • Page 89

    A p p l i c a t i o n 1 8 wa t l o w m i n i c h e f 2 0 0 0 ■ 8 7 step 7 design a faceplate overlay to complete the installation, you must apply a graphic membrane to the front panel of the controller. The following artwork will help you design and create a membrane for this application. For more d...

  • Page 90

    8 8 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 8 step 8 operate the controller summary of key functions in operation mode key operation function a idle one temp b idle two temp c increment d menu select e start/stop f decrement start-up apply power to the fryer and add cooking oil ...

  • Page 91

    A p p l i c a t i o n 1 8 wa t l o w m i n i c h e f 2 0 0 0 ■ 8 9 play and an audible tone will sound for 2 seconds. Then [`idle] will appear on the display. If real time clock option is installed and [setup] / [cloc`] is set to [``yes], the time of day will appear on the display. Preheat if in the...

  • Page 92

    9 0 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 8 if the preheat condition has not been met, the fryer will preheat until [ready] appears on the display. If the fryer is at operating temperature [ready] will immediately appear on the display. 3. With ready on the display, place the ...

  • Page 93

    A p p l i c a t i o n 1 8 wa t l o w m i n i c h e f 2 0 0 0 ■ 9 1 acknowledge and silence the tone by pressing the start/stop key or it will automati- cally time out within 2 seconds for setting 1 or 20 seconds for settings 2 or 3 and then go into idle. The start/stop key indicator light will flash...

  • Page 94

    9 2 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 8 will maintain temperature at the programmed set point. With sound set to 4 or 5: [``end] will appear on the display and the start/stop key indicator light will flash rapidly. You must acknowledge the audible tone by pressing the star...

  • Page 95

    A p p l i c a t i o n 1 8 wa t l o w m i n i c h e f 2 0 0 0 ■ 9 3 based on its programming, the unit will run the menu in one of the ways described earlier. Change menus 1. With the controller in idle, select the menu you want to run by performing the pro- cedure under “select a menu” earlier in th...

  • Page 96: Notes

    9 4 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 8 notes.

  • Page 97: Manual Deepfat Fryer

    A p p l i c a t i o n 1 9 wa t l o w m i n i c h e f 2 0 0 0 ■ 9 5 application 19 manual deepfat fryer one heat channel introduction to application 19 . . . . . . . . . . . . . 95 configuration mode quick reference . . . . . . . . 97 step 7 design a faceplate overlay . . . . . . . . . . 99 step 8 op...

  • Page 98

    9 6 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 9 key functions in configuration mode key functions in operation mode summary of input/output functions note: for details, see wiring instructions in the hardware & software setup guide. Heat 1 temp 2 time 4 5 start/ stop 6 down your c...

  • Page 99

    A p p l i c a t i o n 1 9 wa t l o w m i n i c h e f 2 0 0 0 ■ 9 7 configuration mode quick reference these are the functions, parameters and values included in the configuration mode for this application. You must select application 19 to access them. For directions, see the hardware & software set...

  • Page 100

    9 8 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 9 auto-tuning note: before auto-tuning application 19, [tenp1] in the operations menu must first be set to a value that is typical of your application. (see hardware & software setup guide for information on programming menus.) then se...

  • Page 101

    A p p l i c a t i o n 1 9 wa t l o w m i n i c h e f 2 0 0 0 ■ 9 9 step 7 design a faceplate overlay to complete the installation, you must apply a graphic membrane to the front panel of the controller. The following artwork will help you design and create a membrane for this application. For more d...

  • Page 102

    1 0 0 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 9 step 8 operate the controller summary of key functions in operation mode key function a temp b time c increment d not used e start/stop f decrement startup apply power to the fryer and add cooking oil if necessary. Set the menu set...

  • Page 103

    A p p l i c a t i o n 1 9 wa t l o w m i n i c h e f 2 0 0 0 ■ 1 0 1 five second timeout when using the up or down keys to change a value, if you do not press any key for 5 seconds, the controller will automatically be set to the last value on the display and return to [`idle]. Initial preheat at po...

  • Page 104

    1 0 2 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 9 the melt cycle to avoid burning congealed oil (shortening), a slow heating action may be necessary. If this is desired, be sure that in the configuration mode [etype] / [melt] has been set to [```on]. Then, when the oil temperature...

  • Page 105

    A p p l i c a t i o n 1 9 wa t l o w m i n i c h e f 2 0 0 0 ■ 1 0 3 that is, when the [ready] parameter in the [setup] function of the configuration mode is set to [```no] — and initial preheat power-up has been completed. 1. Set the menu as shown earlier. 2. With [`idle] or time of day on the disp...

  • Page 106

    1 0 4 ■ wa t l o w m i n i c h e f 2 0 0 0 a p p l i c a t i o n 1 9 timer output if [etype]] / [t`out]] in the configuration mode is set to [``yes], when time is count- ing down event output 2 is on. It is off during [pause], [`idle] or [hold]. Temperature alarms the controller will alert you to te...

  • Page 107

    S p e c i f i c a t i o n s wa t l o w m i n i c h e f 2 0 0 0 ■ 1 0 5 specifications (1032) control mode • single and dual heat channels, pid or on/off. 1 • microprocessor-based, programmable, reverse-acting control outputs. • user-selectable embedded application software defines operation of displ...

  • Page 108: Ordering Information

    1 0 6 ■ wa t l o w m i n i c h e f 2 0 0 0 o r d e r i n g i n f o r m a t i o n ordering information (1033) f 2 h a - _ _ _ 1 - _ _ a a m ini c hef ™ 2000 cooking controller with numerous food equipment application software sets, single and dual channel on/off or pid temperature regulation, timer a...

  • Page 109

    O r d e r i n g i n f o r m a t i o n wa t l o w m i n i c h e f 2 0 0 0 ■ 1 0 7 m ini c hef 2000 accessories 0836-0442-0000 sensor input mating connector, (riacon #31007106), 6-position, quick-connect terminal, screw connection for 28-14 awg wires, tighten to 7 in/lb a001-0298-0000 power supply and...

  • Page 110

    Watlow controls watlow controls is a division of watlow electric mfg. Co., st. Louis, missouri, a manu- facturer of industrial electric heating products since 1922. Watlow begins with a full set of specifications and completes an industrial product that is manufactured totally in- house, in the u.S....

  • Page 111

    Watlow m ini c hef ™ 2000 deepfat fryer applications guide watlow controls, 1241 bundy blvd., p.O. Box 5580, winona, mn u.S.A. 55987-5580 phone: (507) 454-5300, fax: (507) 452-4507.