1 for more cool and exciting wattage products, visit our website at http://watt-age.Globalhobby.Com the wattage ezette rtf is distributed exclusively by global hobby distributors 18480 bandilier circle, fountain valley, ca 92728 specifications: ● wing area: 260 square inches ● wing span: 42 inches ●...
2 need help or have any questions? Call us at 1-714-963-0329 or send us an email at service@globalhobby.Net thank you for purchasing the new wattage ezette rtf and welcome to the sport of radio control flying. Before completing the final assembly of your new ezette rtf, please carefully read through...
3 for more cool and exciting wattage products, visit our website at http://watt-age.Globalhobby.Com fuselage assembly wing assembly tail assembly dc peak charger flight battery 3ch. Transmitter propeller before beginning assembly, remove the different parts from the box and use the photos below to v...
4 need help or have any questions? Call us at 1-714-963-0329 or send us an email at service@globalhobby.Net eight aa alkaline batteries adjustable wrench small phillips head screwdriver 7/64" hex wrench scissors section 2: our recommendations this section lists the items you will need to fly your ne...
5 for more cool and exciting wattage products, visit our website at http://watt-age.Globalhobby.Com step 1: installing the transmitter antenna ❑ line up the threaded end of the antenna with the antenna mount in the top of the transmitter. ❑ slide the end of the antenna down into the antenna mount. ❑...
6 need help or have any questions? Call us at 1-714-963-0329 or send us an email at service@globalhobby.Net ❑ carefully remove the battery tray from the transmitter. ❑ install 8 fresh aa alkaline batteries, being careful to watch that the polarity is correct for each battery. ❑ slide the battery tra...
7 for more cool and exciting wattage products, visit our website at http://watt-age.Globalhobby.Com step 3: charging the flight battery ❑ connect the alligator clips from the charger to a 12v dc battery source. A car battery is the best choice. Be very careful to connect the red clip to the positive...
8 need help or have any questions? Call us at 1-714-963-0329 or send us an email at service@globalhobby.Net ❑ push the remaining (shorter) wing joiner into the rear hole using the same technique. Step 4: assembling the wing panels ❑ carefully line up the longer of the two metal wing joiners with the...
9 for more cool and exciting wattage products, visit our website at http://watt-age.Globalhobby.Com ❑ carefully line up the two holes in the second wing panel with the exposed ends of the wing joiners. ❑ carefully push the two wing panels firmly together as shown. The wing panels should fit tightly ...
10 need help or have any questions? Call us at 1-714-963-0329 or send us an email at service@globalhobby.Net ❑ line up the two tail mounting screws in the vertical tail with the two holes in the fuselage. Step 5: installing the tail assembly ❑ remove the two hex nuts and two flat washers that are pr...
11 for more cool and exciting wattage products, visit our website at http://watt-age.Globalhobby.Com ❑ carefully push the vertical tail down until the mounting screws extend out the bottom of the fuselage. You may have to move the horizontal tail slightly to allow the mounting screws to pass through...
12 need help or have any questions? Call us at 1-714-963-0329 or send us an email at service@globalhobby.Net ❑ secure the landing gear straps into place using the four wood screws provided. ❑ tighten the screws firmly using a small phillips head screwdriver. ❑ firmly push both landing gear wires dow...
13 for more cool and exciting wattage products, visit our website at http://watt-age.Globalhobby.Com ❑ slide one wheel collar assembly onto one wire axle. ❑ tighten the set screw firmly using a small phillips head screwdriver. ❑ slide one wheel onto the axle and push it up against the wheel collar. ...
14 need help or have any questions? Call us at 1-714-963-0329 or send us an email at service@globalhobby.Net ❑ push the propeller firmly onto the propeller mount. Step 7: installing the propeller ❑ remove the machine screw and flat washer from the propeller adapter. ❑ before installing the propeller...
15 for more cool and exciting wattage products, visit our website at http://watt-age.Globalhobby.Com ❑ thread the flat washer and machine screw back into place. ❑ tighten the machine screw firmly using a 7/64" hex wrench. Spin the propeller by hand. If any part of it touches the cowling, see page # ...
16 need help or have any questions? Call us at 1-714-963-0329 or send us an email at service@globalhobby.Net ❑ the flight battery slides into place on top of the battery tray. The velcro ® should be facing down and the battery plug should be toward the top of the fuselage. Step 9: installing the fli...
17 for more cool and exciting wattage products, visit our website at http://watt-age.Globalhobby.Com ❑ push the flight battery down as far forward as it will go. The velcro ® will keep it from sliding around or backing out during flight. ❑ plug the connector on the flight battery into the connector ...
18 need help or have any questions? Call us at 1-714-963-0329 or send us an email at service@globalhobby.Net step 11: connecting the control surfaces ❑ turn on the transmitter. The green led should light up. Important before turning on the transmitter, check to make sure the switch on the side of th...
19 for more cool and exciting wattage products, visit our website at http://watt-age.Globalhobby.Com ❑ carefully adjust the left and right and the up and down control trim levers until they are both centered as shown. ❑ double check to make sure the throttle control lever is in the "off" position as...
20 need help or have any questions? Call us at 1-714-963-0329 or send us an email at service@globalhobby.Net step 1: verifying control surface direction ❑ plug in and install the flight battery. ❑ turn on the transmitter, then turn on the airborne system. Warning during this step, make sure to keep ...
21 for more cool and exciting wattage products, visit our website at http://watt-age.Globalhobby.Com ❑ looking from the back of the ezette rtf, move the transmitter control stick completely to the right. The vertical control surface should move right. ❑ looking from the back of the ezette rtf, move ...
22 need help or have any questions? Call us at 1-714-963-0329 or send us an email at service@globalhobby.Net step 1: choosing your flying field ❑ the flying field you choose should be a large, open field with grass. There should not be any vehicles, buildings, power lines, trees, large rocks - or an...
23 for more cool and exciting wattage products, visit our website at http://watt-age.Globalhobby.Com step 2: choosing a day to fly ❑ until you become a proficient flyer you should always plan on flying your ezette rtf when there's no wind. We strongly suggest waiting for a calm day. ❑ snap the red f...
24 need help or have any questions? Call us at 1-714-963-0329 or send us an email at service@globalhobby.Net ● check before every flight to ensure that the batteries in the transmitter are working properly. When the red led begins to flash it's time to change the batteries. ● before recharging the f...
25 for more cool and exciting wattage products, visit our website at http://watt-age.Globalhobby.Com step 1: hand launching ❑ you should always launch the ezette rtf into the wind. Determine wind direction by tossing some blades of grass into the air and watching which direction they fall. ❑ turn on...
26 need help or have any questions? Call us at 1-714-963-0329 or send us an email at service@globalhobby.Net step 3: landing important all landings should be made flying straight into the wind with the wing level. ❑ move the throttle control lever completely to the left to turn off the motor. At thi...
27 for more cool and exciting wattage products, visit our website at http://watt-age.Globalhobby.Com it's possible that after a hard nose-in landing that your motor may be knocked out of alignment. This usually results in the motor being pushed back in the mounts and the propeller hitting the front ...
28 need help or have any questions? Call us at 1-714-963-0329 or send us an email at service@globalhobby.Net this troubleshooting guide has been provided to help you diagnose and solve most problems that you may encounter with your ezette rtf. Most problems encountered can be solved by carefully fol...
29 for more cool and exciting wattage products, visit our website at http://watt-age.Globalhobby.Com battery charger: connects to a 12 volt source and charges the flight battery to full capacity. Clevis: part of the control system, either made out of nylon or metal. It connects the pushrod to the co...
30 need help or have any questions? Call us at 1-714-963-0329 or send us an email at service@globalhobby.Net.
31 for more cool and exciting wattage products, visit our website at http://watt-age.Globalhobby.Com instruction manual - 145060 wing set - 145061 fuselage assembly - 145062 wing tips (1 pair) - 145063 tail assembly set - 145064 wing joiner rods - 145065 landing gear wires (w/hardware) - 145066 push...
32 need help or have any questions? Call us at 1-714-963-0329 or send us an email at service@globalhobby.Net warranty service before returning your ezette rtf for warranty consideration, the status of the unit must be within the guarantee as stated above. Do not return your airplane to the place of ...
