Watts PWFCAL15 Installation, Operation And Maintanance Manual

Manual is about: PWFGAC PWFMZ PWFC Series

Summary of PWFCAL15

  • Page 1

    Pwfgac pwfmz pwfc series iom-wq-pwfgac-pwfmz-pwfcal do not use with water that is microbiologically unsafe or of un- known quality adequate disinfection before and after the system. Warning ! Notice hydrocarbons such as kerosene, benzene, gasoline, etc., may damage products that contain o-rings or p...

  • Page 2

    2 pwf filter systems specifications feed water parameters minimum inlet pressure: 30 psig maximum operating pressure: 125 psig minimum water temperature: 40°f (5°c) maximum water temperature: 110°f (43°c) power voltage: 120vac frequency: 60hz power consumption: 7 watts maximum installation location:...

  • Page 3

    Pwf filter systems 3 warning ! This water conditioner’s control valve conforms to ul/ ce standards. Generic valves were tested and certified for compliance as verified by the agency listing. This water conditioning system is to be used only for potable water. Inspect the water conditioning system fo...

  • Page 4

    4 pwf filter systems 1 noryl is a trademark of sabic. How to use this manual this installation manual is designed to guide the installer through the process of installing and starting up water conditioning systems featuring the pwf controller. This manual is a reference and will not include every sy...

  • Page 5

    Pwf filter systems 5 safety information this water conditioner’s control valve conforms to ul/ce standards. Generic valves were tested and certified for compliance as verified by the agency listing. • please review the entire installation and operation manual before installing the water conditioning...

  • Page 6: Service Instructions

    6 pwf filter systems warning ! Do not exceed water pressure of 120 psi (8.2 bar). Do not exceed 110°f (43.3°c). Do not subject unit to freezing conditions. General installation instructions 1. Turn off water heater(s). 2. Turn off the main water supply to the home and open an inside faucet (cold and...

  • Page 7

    Pwf filter systems 7 bypass valve installation 7 installation figure 1: plumbing with by pass (standard). Figure 3: bypass (standard). Figure 6: figure 2: plumbing with 3-way b pass. Figure 4: 3-way bypass plumbing. When installing sweat copper follow state and fed- eral codes by using a lead free s...

  • Page 8

    8 pwf filter systems notice when assembling the installation fitting package, connect the fitting to the plumbing system first and then attach the nut, split ring and o-ring. Heat from soldering or solvent cements may damage the nut, split ring, and o-ring. Make sure solder joints are cool before as...

  • Page 9

    Pwf filter systems 9 figure 8: drain line connection 9 installation step 5: connect the drain line if the drain line is a 5/8" flexible poly tube, slide the nut onto the poly tube, then place the poly tube insert into the end of the poly tube and tighten the nut on to the 3/4" drain line fit- ting. ...

  • Page 10: Pwf System Programming

    10 pwf filter systems pwf system programming pwf quick programming guide a quick programming guide has been listed below for convenience specifically for the pwf series filter systems. For other programming requirements not listed in the quick programming guide, please see the detailed programming s...

  • Page 11

    Pwf filter systems 11 press the set button approximately 5 seconds adjust hours using the up and down arrow buttons press the set button to advance to the minutes. Adjust minutes with the up and down arrow buttons. Press the set button to set time to exit chart 1: setting time of day notice once in ...

  • Page 12

    12 pwf filter systems programming step 1ss – from normal mode, press set hour + up buttons simultaneously for 3 seconds and release. Then press set hour + up buttons simultaneously for 3 seconds and release. Step 2ss – choose the desired program by pressing the up or down buttons. Prior to selecting...

  • Page 13

    Pwf filter systems 13 is added to the solution tank. With salt (sodium chloride) this equates to approximately 1 1/2 pounds of salt per minute of fill. Step 4ss — use up or down buttons to switch between: • 1-99 days between regen; or • 7-day. Press set hour button to go to step 5ss. Step 5ss — use ...

  • Page 14

    14 pwf filter systems settings in this display are ignored. Press set hour to exit oem system setup. Installer displays & settings (1-99 days between regeneration option) step 1id – from normal mode, press set hour + up buttons simultaneously for 3 seconds and release. Step 2id – backwash time: set ...

  • Page 15

    Pwf filter systems 15 step 6i7 – tuesday backwash: to regenerate on tuesday use the up or down button until the arrow points to regen. If the arrow does not point to regen a regeneration will not occur on tuesday. Press set hour to go to step 7i7. Step 7i7 – wednesday backwash: to regenerate on wedn...

  • Page 16

    16 pwf filter systems set time of day step 1u – press set hour step 2u – current time: set the clock to the closest hour by using the up and down button. An arrow points to pm after 12. After a power outage, the time of day will need to be reset. Press set hour to exit. When the system begins to bac...

  • Page 17

    Pwf filter systems 17 notes.

  • Page 20

    Limited warranty: certain watts products come with a limited warranty from watts regulator co. Other products may have no warranty or are covered by the original manufacturer’s warranty only. For specific product warranty information, please visit www.Watts.Com or the published literature that comes...