Wave Broadband User Manual - page 5

5

Programming Your Remote Control

For additional settings and information, please visit wavebroadband.com.

Auto Search Method

Your cable remote may be used to control other 

devices within your entertainment system. You 

can use the Auto Search Method to find the correct 

code number for your equipment by following the 

steps below:

STEP 1  Turn on the equipment you wish to 

operate with the remote.

STEP 2 

Press the device button (TV, VCR, DVD, 

or AUX) to be programmed and the [OK/SELECT] 

button simultaneously for 3 seconds. The device 

button LED will turn on.

TIP:

The device button LED will turn on for 30 seconds. 

The next step must be entered while LED is on.

STEP 3 

Point the remote toward the equipment 

and press the [CH+] or [CH-] button one at a time 

or keep it pressed. The remote will emit a series 

of power on/off commands. Release the [CH+] or 

[CH-] button as soon as the equipment turns off.

TIP:

You can verify that you selected the correct code by 

pressing the [POWER] button. The equipment should 

either turn on or off.

STEP 4 

Press the same device button to store 

the code. The device button LED will blink twice to 

confirm that the code has been stored.

It is possible to manually enter a code that directly 

corresponds to the brand of your device.  Refer 

to the instruction manual that came with your 

remote, or to view the manual online, please visit 

wavebroadband.com.

Programming Volume Control

By following the steps below, you can program the 

volume controls (Volume Up and Volume Down) 

from one device to operate in another device 

mode. The default volume control settings on the 

remote control are as follows:

CBL: TV TV: 

TV 

VCR: TV 

DVD: TV 

AUX: AUX

If you wish to store the TV volume control in CBL 

mode, use the following steps.

STEP 1  Press the [CBL] button and the [OK/

SELECT] button simultaneously for 3 seconds. The 

[CBL] device LED will turn on.

TIP: 

The device button LED will turn on for 30 seconds. 

The next step must be entered while LED is on.

STEP 2 

Press the [VOL+] button.

STEP 3 

Press the [TV] button. The device LED 

will blink twice to confirm the programming.

To return to the original state:

If you wish to restore the CBL volume control to 

CBL mode, repeat the above steps by pressing 

[CBL] in STEP 3.

Programming for Advanced Function

In the CBL mode, the M [MACRO] button can be 

programmed to act as a macro or favorite channel 

button. You can program up to three separate 

channels that can be accessed with a simple press 

of the M button.

STEP 1 

Press the [CBL] button to select the CBL 

mode on your remote.

STEP 2 

Press the [M] button and [OK/SELECT] 

button simultaneously for 3 seconds. the [CBL] 

device LED will turn on for 30 seconds.

STEP 3 

Enter the 3 or 4-digit channel number 

you want programmed first (for example, 007) 

using the Number Pad, then press the [STOP] 

button.  Then enter the code for the next channel 

(for example, 050), then press the [STOP] button.  

Repeat this process for the third channel.  The [CBL] 

button will blink once for each channel entered.

STEP 4  Press the [CH+] button to store the 

functions that were selected. The [CBL] device LED 

will blink twice to confirm storage of the functions.

Low Battery Warning

When the batteries are low and need to be 

replaced, the remote control LED will blink 2 

times in sequence whenever a [POWER] button is 

pressed to turn on equipment.