Summary of z250
Page 1
Operation manual digital vehicle compass z 250
Page 2
Making ordinary products extraordinary.
Page 3: Features
1 you have acquired one of the most sophisticated compasses available for use in a vehicle, rv or boat. The wayfinder z250 utilizes patented magnetic sensor technology that was developed for the united states military to give you the most accurate electronic compass headings. The built-in compasses ...
Page 4: Installing The Wayfinder
2 modes, buttons and display . . . . . . . . . . . 4 resetting the wayfinder . . . . . . . . . . . . . . . 7 installing the wayfinder installation guidelines . . . . . . . . . . . . . . . .8 windshield mounting . . . . . . . . . . . . . . . 8 adjusting the bracket . . . . . . . . . . . . . . . 9 rem...
Page 5: Modes
3 modes the wayfinder z250 has 2 modes: 1. Basic compass: in this mode, cardinal point and numeric heading readouts appear. The “basic” icon also appears in the upper right corner. 2. Timer: in this mode, cardinal point, timer, and numeric heading readouts appear. There is no icon showing for this m...
Page 6: Timer Readout
4 timer readout the timer is a standard counter that records a maximum of 99 hours, 59 minutes, and 59 seconds. The wayfinder can be used as a timer while still maintaining accurate compass readings. “distortion” icon the wayfinder detects when outside magnetic interference is compromising compass a...
Page 7: Modes, Buttons and Display
55 distortion basic modes, buttons and display “distortion” cardinal point numeric heading icon readout readout adv button ent button basic mode icon modes, buttons and display.
Page 8: Resetting The Wayfinder
6 resetting the wayfinder a manual reset has been added to the way- finder. Resetting the unit erases everything that is stored in memory including calibra- tion, the automatic shut-off values, and timer settings. Resetting the wayfinder should only be done when you want to completely erase the memo...
Page 9: Installation Guidelines
7 installation guidelines • choose a place on the windshield that will not obstruct the driver’s view and is within reach so the buttons are easy to push. Make sure the windshield surface is clean. Once installed, the face of the compass must be pointing toward the rear of the vehicle. • the unit ca...
Page 10: Windshield Mounting:
8 audio speaker. It is recommended that the unit be mounted 5 or more inches away from stereo speakers. Windshield mounting: 1. Install the suction cups into the mounting bracket by sliding them into their holes 2. Press the suction cup base firmly against the windshield. If necessary, apply a thin ...
Page 11: Adjusted.
9 allows the compass to be gently pulled out of the bracket. Removing only the compass and not the bracket assures the compass will be mounted in the same location as it was previously. When reinstalling the compass, make sure the angle of the wayfinder in the bracket is the same as it was before ir...
Page 12: Header
10 header basic mode the wayfinder must be in basic mode to use any of the features described in this section. Features the basic mode provides the current com- pass heading and allows you to program your compass. Within the basic mode there are three programmable functions: 1. Calibration: the comp...
Page 13: Header
Header 11 when to calibrate : the wayfinder must be calibrated when: 1. It is being used for the first time. 2. It is being used in a different location than it was previously calibrated in. 3. The “distortion” icon displays con- tinuously. 4. The battery is removed or replaced. Steps to calibrate :...
Page 14: Header
12 header the circles do not need to be perfect circles but must be completed in the same direction and must be completed in less than 2 minutes. Compass automatic shut-off the wayfinder has a programmable compass shut-off feature. The default value for the compass shut-off is 5 minutes, meaning tha...
Page 15: Header
Header 13 90 or off. Stop at your desired selection for the compass time-out. 6. Press the ent button once to set your selected time-out and “c” and the select time-out value should flash. 7. Press adv twice to exit out of programming mode. The display should now be in basic mode. While in programmi...
Page 16: Header
14 header steps to select the backlight shut-off : 1. Press the adv button until the “basic” icon is displayed in the upper right corner. 2. Press and hold the adv button and “cal” flashes. 3. Press the adv button two more times (in this case “l” stands for light and 10 is ten seconds.) 4. Press the...
Page 17: Header
Header 15 features the timer is a standard counter that logs a maximum of 99 hours, 59 minutes and 59 seconds, “99:59:59”. The wayfinder can be used as a compass while still using the timer. When counting, the timer starts at “00:00:00”. If the timer reaches its maximum, it resets to “00:00:00” and ...
Page 18: Header
16 header the timer can be paused any number of times. The timer will continue to run even though the wayfinder is in a different mode or has timed-out. The timer will continue to run until it is paused or reset. Battery life of the wayfinder is dependent upon usage, but on average the battery life ...
Page 19: Header
Header 17 and the battery. Do not disturb the rubber seal that is resting on the case front. 4. Remove the battery. Do not remove the pcb; it is held in place with friction pins and must be left in the case front to maintain proper alignment with other components. This is necessary to ensure a water...
Page 20: Header
18 header changing the battery pressure to maintain a water-tight seal. 9. The display should function properly at this point. If it does not, remove the battery, wait several seconds, and reinsert the battery. 10. Since the battery has been removed, it is necessary to re-calibrate the wayfinder. Pc...
Page 21: Header
Header 19 how does the wayfinder work? The wayfinder uses a patented magnetic sensor technology that was developed by pni corpo- ration for the u.S. Military. This technology is called “magneto-inductive” and is the largest advance in compass technology since the flux gate was invented 60 years ago....
Page 22: Header
20 header when do i need to calibrate the wayfinder? The wayfinder needs to be calibrated when used for the first time in a vehicle, when used in a different location in the same vehicle, when moved to a different vehicle or when the battery was removed. The wayfinder requires re-calibration when th...
Page 23: Header
Header 21 customer service please e-mail customer service department at customerservice@pnicorp.Com or call us between the hours of 8:00 a.M. And 5:00 p.M. (pst) monday through friday, with your questions. Warranty service for the fastest service, it is best to contact or return your unit to the pla...
Page 24: Header
22 header place of purchase. Once you have acquired an rma number, pack the unit securely to prevent damage in transit. If possible, use the original packing material and box. Be sure to send the entire product. 3. Ship prepaid and insured by way of a traceable carrier, such as united parcel service...
Page 25: Header
Header 23 pni corporation manufactures its products from parts and components that are new or equivalent to new in performance and warrants to the original user that this product will be free of defects in workmanship and materials for one (1) year from the date of purchase. This warranty does not c...
Page 26: Header
24 header warranties or representations, expressed or implied, in fact or in law, with respect to this product, including, but not limited to, (1) the implied warranties of merchantability and of fitness for a particular purpose, or (2) that use of the product will be uninterrupted and error free. P...
Page 28: Pni Corporation
Pni corporation www.Pnicorp.Com 11188 r02 1000063.