Wayne-Dalton 8300 Installation Instructions And Owner's Manual

Manual is about: Extension Residential Standard Lift

Summary of 8300

  • Page 1

    Important notice! To avoid possible injury, read the enclosed instructions carefully before installing/ operating this garage door. Pay close attention to all warnings and notes. After installation is complete, fasten this manual near garage door for easy reference. These instructions are available ...

  • Page 2: Warning

    Important safety instructions definition of key words used in this manual: warning warning indicates a potentially hazardous situation which; if not avoided, could result in severe or fatal injury. Caution: property damage or injury can result from failure to follow instructions. Important: required...

  • Page 3: Warning

    5/16” x 1 5/8” hex head lag screws (as required) 1/4”-20 x 11/16” self drilling screws (as required) 1/4”-20 x 5/8” self drilling screws (as required) (2) 5/16”-18 hex nuts (2) 3/8”- 16 hex nuts 1/4”- 20 flanged hex nuts (as required) 3/8” washer 1/4”-20 x 7/8” self drilling screws (as required) 1/4...

  • Page 4

    2-1/2” (64 mm) of additional headroom is required. Backroom requirement: backroom is defined as the distance needed from the opening back into the garage to allow the door to open fully. Backroom requirements door height track manual lift motor operated 8’3” to 9’0” 12”,15” radius 126” (3200 mm) 168...

  • Page 5: Warning

    Installation before installing your door, be certain that you have read and followed all of the instruc- tions covered in the pre-installation section of this manual. Failure to do so may result in an improperly installed door. Bottom brackets and counterbalance 1 tools: power drill, 7/16” socket dr...

  • Page 6

    Please do not return this product to the store. Contact your local wayne-dalton dealer. To find your local wayne-dalton dealer, refer to your local yellow pages business listings or go to the find a dealer section online at www.Wayne-dalton.Com 8300 lt-com aluminum strutting schedule---brown colored...

  • Page 7: Warning

    Please do not return this product to the store. Contact your local wayne-dalton dealer. To find your local wayne-dalton dealer, refer to your local yellow pages business listings or go to the find a dealer section online at www.Wayne-dalton.Com 8500 lt-com steel strutting schedule---brown colored do...

  • Page 8

    Please do not return this product to the store. Contact your local wayne-dalton dealer. To find your local wayne-dalton dealer, refer to your local yellow pages business listings or go to the find a dealer section online at www.Wayne-dalton.Com flag angle lag screw locations vertical track jamb brac...

  • Page 9: Warning

    Please do not return this product to the store. Contact your local wayne-dalton dealer. To find your local wayne-dalton dealer, refer to your local yellow pages business listings or go to the find a dealer section online at www.Wayne-dalton.Com (4) 1/4”- 20 x 5/8” self-drilling screws (3) 1/4”- 20 x...

  • Page 10

    Please do not return this product to the store. Contact your local wayne-dalton dealer. To find your local wayne-dalton dealer, refer to your local yellow pages business listings or go to the find a dealer section online at www.Wayne-dalton.Com center bearing bracket (1) 5/16” x 2” or (1) 5/16” x 1-...

  • Page 11: Warning

    Please do not return this product to the store. Contact your local wayne-dalton dealer. To find your local wayne-dalton dealer, refer to your local yellow pages business listings or go to the find a dealer section online at www.Wayne-dalton.Com securing door for spring winding 19 tools: vice clamps ...

  • Page 12

    Please do not return this product to the store. Contact your local wayne-dalton dealer. To find your local wayne-dalton dealer, refer to your local yellow pages business listings or go to the find a dealer section online at www.Wayne-dalton.Com vice clamp horizontal tracks 2nd roller vice clamp 5/16...

  • Page 13: Warning

    Trolley arm hookup tools: needle nose pliers note: if wayne-dalton operator/ trolley bracket was installed, follow these directions. Align hole in the door arm with holes in operator bracket tabs, as shown. Attach with 5/16”-18 x 3-1/2” hex bolt, 3/8” washer and 5/16”-18 nut. Trolley arm operator br...

  • Page 14: Warning

    Opening a door: make sure the lock(s) are in the unlocked position. Lift the door by using the lift handles/ suitable gripping points only. Door should open with little resistance. Closing a door: from inside the garage, pull door downward using lift handles/ gripping point only or a high friction a...

  • Page 15

    Lifetime limited warranty models 8300, 8500 subject to the terms and conditions contained in this lifetime limited warranty, wayne-dalton corp. (“manufacturer”) warrants the sections of the door, which is described at the top of this page, for as long as you own the door against: the door becoming i...

  • Page 16

    Covered by one or more of the following patents; 5,408,724; 5,409,051; 5,419,010; 5,495,640; 5,522,446; 5,562,141; 5,566,740; 5,568,672; 5,718,533; 6,019,269; 6,089,304; 6,644,378; 6,374,567; 6,561,256; 6,527,037; 6,640,872; 6,672,362; 6,725,898; 6,843,300; 6,915,573; 6,951,237; 7,014,386; 7,036,548...