- DL manuals
- Weber
- Power Tool
- SRV 62
- Operating and maintenance instructions manual
Weber SRV 62 Operating and maintenance instructions manual
Summary of SRV 62
Page 1
Srv62_66 1 operating and maintenance instructions weber maschinentechnik gmbh p.O. Box 21 53, d-57329 bad laasphe-rückershausen phone ++27 54 / 398-0 fax (++ 27 54) 3 98-101 (switchboard) & 3 98-102 (spare parts) srv 62 honda gx 100 srv 66 robin eh 12-2 0506-englisch ramirent.
Page 2
2 srv62_66 ramirent.
Page 3: Preface
Srv62_66 3 preface these operating and maintenance instructions describe the safe operation of the srv 62/66 tampers. Please read this operation manual and familiarize yourself with all details of your tamper before operating the machine for the first time. Carefully follow all instructions and alwa...
Page 4: General Safety Instructions
4 srv62_66 general safety instructions general all safety notes (see also explanations of the pictogram meanings in the preface) must be read and observed (any lack of clarity must be dispelled before the tamper is put into operation), because otherwise the use of the machine may * constitute a risk...
Page 5: Table of Contents
Srv62_66 5 table of contents preface ........................................................................................................................................................... 3 general safety instructions ................................................................................
Page 6: 1. Technical Description
6 srv62_66 1. Technical description figure 1 overall view srv 1 fuel tank 6 reversible starter (not shown) 2 tank cap 7 4-stroke engine 3 engine speed adjusting lever (not shown) 8 tamping shoe 4 handle 9 bellow 5 air filter 10 upper tamper part 11 lower tamper part 1.1 illustration 1 2 4 5 7 8 9 11...
Page 7
Srv62_66 7 1.2 machine description the tampers of the srv 62/srv66 series are used for the compaction of crushed stone and sand on flat surfaces and for canal construction work. The srv 62/66 tamper is driven by a 4-stroke honda/ robin gasoline engine (1/7). Important! Please refer to paragraph 1.3 ...
Page 8
8 srv62_66 1.3 specifications srv 62 srv 66 weight operating weight cece (in kg) 66 73 dimensions overall lenght (in mm) 690 690 overall width (in mm) 380 400 height (in mm) 1130 1130 tamping shoe width (in mm) 280 280 no.Of impacts (/min) 700 670 stroke (in mm) 65 70 propulsion engine manufacturer ...
Page 9
Srv62_66 9 3 4 1 machine number 3 type .................................................... ................................................... 2 year of construction 4 engine/serial no. .................................................... .................................................... Srv 62 ...
Page 10: Operation
10 srv62_66 2 operation 2.1 safety precautions for the operation safety and protective devices before every shift, the operator must check the operativeness of all controls and safety elements as well as the proper installation of all protective devices. The tamper is only allowed to be operated wit...
Page 11
Srv62_66 11 2.2 transport for transporting the tamper over long distances, however, the machine can be lifted on an appropriate transport vehicle (truck, trailer) by means of a crane. 2.2.1 loading by crane - put the tamper out of operation as described in paragraph 2.7. - hang the crane hook into t...
Page 12
12 srv62_66 2.4 pre-start work - check to ensure that all safety devices are in place. Check the whole tamper for evident damage (visual check). - check all screwed connections for tight seat, retighten them if necessary. - check the fuel level, if necessary, add fuel (refer to paragraph 2.4.1). - c...
Page 13
Srv62_66 13 2.4.2 checking the engine oil level figure 4 figure 4 a figure 5 figure 6 2.4.2.1 srv 62 caution! The engine oil level must be checked with the tamper standing horizontally on the ground. - pull out the oil filler screw by means of the oil dipstick (4/1), wipe it off with a clean, non-fl...
Page 14
14 srv62_66 2.5 starting danger! Before starting the machine, always ensure that nobody is in the danger area of the tamper and that all protective devices are properly in place. When starting the tamper in closed premises, always ensure a proper ventilation - danger of poisoning. Caution! Never use...
Page 15
Srv62_66 15 2.5.2 starting the srv 66 - turn the stop button (11/1) to the right into the „on“ position. - put the fuel stop cock (12/1) into the vertical position to open it. - open or close the choke (13/1) according to the engine and/or ambient temperature. - in case of a cold engine and/or low a...
Page 16
16 srv62_66 2.6 tamping operation - start the tamper (refer to paragraph 2.5). - always push the speed adjusting lever into the full gas position. Caution! Compaction work is only allowed to be done at full engine speed, otherwise the centrifugal clutch may slip and cause increased wear. Danger! If ...
Page 17
Srv62_66 17 2.7.1 stopping the srv 62/srv 66 - push the speed adjusting lever (16/1) to the right side and let the engine idle for a few minutes. - close the fuel cock (17/1). - turn the stop button (16/2) to the left side into the „off“ position. Figure 17 figure 16 1 1 2 ramirent.
Page 18: Maintenance
18 srv62_66 3 maintenance 3.1 safety precautions for maintenance work checks depending upon the operating conditions, tampers must be made subject to an expert's check for operational safety when required, but at least once a year. The inspection results must be recorded in writing and kept at least...
Page 19
Srv62_66 19 3.2 maintenance survey any maintenance work which must be performed on the tamper is listed in two charts. The first chart (paragraph 3.2.1) indicates the initial maintenance work which has to be carried out once at a certain time after commissioning. The routine maintenance work indicat...
Page 20
20 srv62_66 3.2.2 routine maintenance maintenance interval maintenance item maintenance work remarks every 8 operating hours whole machine - check for visible damage, leaks etc. Air filter - clean the air filter cartridge, check it for damage and, if necessary, replace it # 3.3.2 engine - check the ...
Page 21
Srv62_66 21 3.3 description of the maintenance work - put the tamper out of operation as described in paragraph 2.7. Caution! Drain off the engine oil at operating temperature and with the engine in horizontal position only. - put a drain pan under the outlet. Environment hazard! Choose a drain pan ...
Page 22
22 srv62_66 - put the tamper out of operation as described in paragraph 2.7. Caution! Drain off the engine oil at operating temperature and with the engine in horizontal position only. - put a drain pan under the outlet. Environment hazard! Choose a drain pan having a sufficient capacity to catch al...
Page 23
Srv62_66 23 3.3.3 cleaning/replacing the air filter cartridge - loosen the snap clips (23/1) and remove the cover (23/2) from the air filter housing. - pull out the air filter element (24/2) and remove the pre-cleaner (24/1). - wash out the pre-cleaner (24/1) in benzine and let it dry. - knock or bl...
Page 24
24 srv62_66 3.3.5 cleaning the fuel filter 1 2 figure 25 3.3.6 adjusting/replacing the spark plug srv 62/srv 66 - pull off the spark plug socket (27/1) and undo the spark plug. - clean the electrodes (28/1) of the spark plug. - measure the air gap, gap: 0.6 - 0.7 mm. - if necessary, correct the air ...
Page 25
Srv62_66 25 3.3.7 changing the oil in the tamper system - remove the plug (29/1) from the filler opening. - slightly tilt the tamper to the front and catch the used oil in an appropriate pan. - put the tamper to the back so that the filler opening is directed towards the top. - pour 1 liter of oil i...
Page 26
26 srv62_66 3.4 consumables and quantities assembly group summer winter srv srv quality 62 66 engine engine oil sae 10 w 40 0,3 l 0,4 l (-10 ~ + 50 °c) api - cd ce or shpd or ccmc - d2 - d3 - pd1 fuel tank gasoline 2,3 l 2,3 l lower tamper part hydraulic oil hlp 68 1 l 1 l regular gasoline, unleaded...
Page 27
Srv62_66 27 4 malfunctions during operation 4.1 general if a malfunction occurs on the tamper, proceed as follows: - put the tamper out of operation as described in paragraph 2.7. - determine the source of the malfunction (refer to paragraph 4.2 - trouble shooting). - eliminate the malfunction (refe...
Page 28
28 srv62_66 4.2 trouble shooting failure possible cause remedy remarks tamper does not start mistake in operating the unit perform the start procedure as described # 2.5 lack of fuel check the fuel level # 2.4.1 dirty air filter clean/replace the air filter # 3.3.2 dirty fuel filter replace the fuel...
Page 29: 5 Preserving The Machine
Srv62_66 29 5 preserving the machine 5.1 preservation measures 5.2 removing machine preservatives if the tamper is planned to be put out of operation for an extended period of time (approx. 1 ... 6 months), e. G. During the winter season, it must be stored in a frost-proof and dry room. Before stori...
Page 30
30 srv62_66 ramirent.
Page 31
Srv62_66 31 6 weber maschinentechnik gmbh for problems, questions and further information refer to one of the following addresses: in germany weber maschinentechnik gmbh postfach 2153 57329 bad laasphe - rückershausen telefon telefax e-mail + 49 (0) 2754 - 398-0 + 49 (0) 2754 - 398101-switchboard + ...
Page 32
32 srv62_66 weber maschinentechnik gmbh im boden d- 57334 bad laasphe - rückershausen p. O. Box 2153 d - 57329 bad laasphe phone ++27 54 / 398 0 - telefax ++27 54 / 398 101 > vibratory plate compactors > vibratory tampers > vibratory rollers > joint cutters > poker vibrators and converters > rotary ...