1. DL manuals
  2. Weber
  3. Grill
  4. Vieluxe 27 Built-In Grill
  5. Installation Manual

Weber Vieluxe 27 Built-In Grill Installation Manual - Install Flavorizer

Other manuals for Vieluxe 27 Built-In Grill: Owner's Manual
Manual is about: Model 360251, Model 370251, Built-In Liquid Propane Gas Grill

Summary of Vieluxe 27 Built-In Grill

  • Page 1

    Vieluxe ® 27" built-in grill (model #: 360251) vieluxe ® 39" built-in grill (model #: 370251) any surface any surface 26 inches any surface 26 inches 26 inches grill frame 24 inches min. For lid clearance warning: the structure, “island”, countertops, and adjacent work areas for the built-in grill i...

  • Page 2: Built-In Structure

    27” grill 39” grill tolerances a 40 1 ⁄ 4 ” 52 1 ⁄ 4 ” b 36” 36” c 23” 23” + 1 ⁄ 4 - 1 ⁄ 4 + 1 ⁄ 4 - 1 ⁄ 4 + 1 ⁄ 4 - 1 ⁄ 4 2 built-in structure cutout dimensions built-in cutout dimensions warning: all countertop finished surfaces must be constructed of a noncombustible material. Note: if the suppor...

  • Page 3: Typical Bulk Propane

    3 typical bulk propane gas supply installation gas line piping ■ refer to the piping chart at the bottom of the page. ■ the corrugated gas line from the manifold is 48 inches long. Do not extend the gas line. ■ we have provided the means to make an sae 45° flare connection. Do not use pipe sealant o...

  • Page 4: Typical 20Lb Propane

    4 gas line piping (continued) ■ copper tubing must be tin-lined if the gas contains more than 0.3 grams of hydrogen sulfide per 100 cubic feet of gas. ■ plastic tubing is suitable only for outdoor, underground use. ■ gas piping in contact with earth, or any other material which may corrode the pipin...

  • Page 5

    5 floor level. The ventilation openings should have a total free area of not less than 10 square inches. (this relates to 1/2 square of ventilation area, per pound of stored fuel capacity). There should be at least two ventilation openings if the ventilation openings at floor level are in the sidewa...

  • Page 6: Connect Gas Supply

    6 test connections all connections and joints must be thoroughly tested for leaks in accordance with local codes and all listed procedures in the latest edition of ansi z223.1/nfpa 54. Danger do not use an open flame to check for gas leaks. Be sure there are no sparks or open flames in the area whil...

  • Page 7: Built-In Grill

    7 built-in grill installation gas line adjustable feet grill frame foot fully extended and secured foot not fully extended caution: use two people to lift and install the vieluxe ® grill. 1) lift the grill out of the packaging. 2) make sure that the adjustable feet are fully extended and secure befo...

  • Page 8: Ventilation

    8 or view of right side view of left side front view back view or warning: air holes must be provided in the structure at the top and bottom to provide ventilation in the event of a gas leak. Air holes can be located in a low visibility area and should be protected by screening material to prevent r...

  • Page 9: Remove Packaged Contents

    9 remove packaged contents catch pan cooking grate vieluxe ® 27" built-in (2) vieluxe ® 39" built-in (3) vieluxe ® smoker (1) note: remove all packaging materials from the grill, the front, back, sides, inside the grill cart, and the bottom shipping platform. Once the packaging material is removed, ...

  • Page 10: Install Flavorizer

    10 flavorizer ® bar/cooking grill support flavorizer ® bar slot install flavorizer ® bars vieluxe ® 27" built-in parts required: (2) flavorizer ® bar assemblies & (1) single flavorizer ® bar. Set the flavorizer ® bar assemblies and single flavorizer ® bars front to back over the burners in the slots...

  • Page 11: Install Smoker

    11 install smoker parts required: smoker box and smoker flues. Set the smoker box into the left side of the cooking box next to the flavorizer ® bars. Then insert smoker flues with tabs into the cut-out of smoker box. The flues need to lay flat on top of the flavorizer ® bars. Note: for directions o...

  • Page 12: Install Warming Rack

    12 install warming rack part required: warming rack. Install the warming rack into the slots at the right and left side of the cooking box. Vieluxe ® 27" built-in vieluxe ® 39" built-in mounting slots tabs of bottom tray view from front of the cooking box install bottom tray parts required: bottom t...

  • Page 13: Install Catch Pan

    13 install catch pan part required: catch pan. Take the catch pan by its handle and slide it into the catch pan holder under the bottom tray. Warning: the storage space under the cooking module is intended for storage of nonflammable items only. Vieluxe ® 27" built-in vieluxe ® 39" built-in slide th...