1. DL manuals
  2. WebGate
  3. DVR
  4. eDVR MD800M
  5. Installation Manual

WebGate eDVR MD800M Installation Manual

Summary of eDVR MD800M

  • Page 1

    Edvr installation guide md800m (v 1.0).

  • Page 2

    Caution since this device is operation purpose and registered as suitable electromagnetic waves, seller or user should be cautios on this point. If the device is sold or purchased wrongly, it is required to replace as home use. Fcc compliance statement caution : any changes or modifications in const...

  • Page 3

    Important otice 1. Do not place heavy objects on the top of the edvr 2. Edvr is for indoor use. It is not weatherproof. Use edvr with referring to its environmental specifications (temperature & humidity). To clean the edvr, gently wipe the outside with a clean dry cloth. 3. Edvr use ac power of 110...

  • Page 4

    4 contents overview .................................................................................................................................. 7 1. What is md800m? ................................................................................................................ 7 2. Supplied a...

  • Page 5

    5 8.2.7. Apply date/time .................................................................................................. 22 8.3. Setting recording condition ........................................................................................... 23 8.3.1. Configuration status ....................

  • Page 6

    6 12. Using control center lite ................................................................................................ 43 12.1. Starting .................................................................................................................... 43 12.1.1. Pc system requirements fo...

  • Page 7

    7 overview 1. What is md800m? The edvr md800m is 8-analog channels network digital video recorder. Video, audio, text and event- logs are digitized and stored on two internal hard-drives - it supports 8ch video input - supports 1 ch bi-directional audio - supports recording, playback, network record...

  • Page 8

    8 2. Supplied accessories unpack and check all the items as below; 1. Edvr md800m (1ea) 2. Ac power cord (1ea) 3. Cd (including software) (1ea) 4. Remote controller (1ea) 5. Power (applied adaptor) (1ea).

  • Page 9

    9 3. Description & function md800m front (1) function buttons (2) led (3) usb port (4) remote controller receiver (5) cd/dvd-rw rom (6) shuttle.

  • Page 10

    10 md800m rear (7) power connector (8) terminal block for sensor, relay, and serial input/output (9) audio input/ output connector (10) bnc connector for video input (11) bnc connector for video output (12) vga connector for video output (13) serial input/output (14) esata connector (15) ethernet co...

  • Page 11

    11 istallatio ad coectio 4. Connecting & running 4.1. Connecting camera (1) connect cctv camera to md800m with bnc cable as below. Ote> 1. The video type for all channels should be either ntsc or pal, not be combined both. 2. Md800m sets video signal’s impedance (75Ω) automatically. Impedance is set...

  • Page 12

    12 4.2. Connecting monitor (1) connect cctv monitor to md800m with bnc cable as shown below; 4.3. Audio connection (1) connect auto signal to md800m with using rca cable..

  • Page 13

    13 4.4. Power supply (1) connect power cable as shown below ote> 1. When supplying power, md800m starts booting automatically. 2. In order to cut off power, press the power switch on md800m front during 4 seconds and enter admin password after appearing a pop window. 3. For power supply again, push ...

  • Page 14

    14 5. Running osd menu 5.1. Structure of menu press the [menu] in keypad of front to open the osd configuration menu (1) main menu : the selected tab is shown in blue and the related sub-menu will be shown below the tab. To movo to the previous/next main menu tab, use the [◀/▶] arrow buttons. To mov...

  • Page 15

    15 5.2. Dialogue box to edit a word there are two methods to input a word.. (1) entering words move pressing [▶] arrow button to enter next word until the word is looking for is shown using [▲/▼] arrow buttons. In case of spacing words, press [▶] to move one space and enter the word. To exit the dia...

  • Page 16

    16 6. Setting remote controller when controlling several edvrs with one remote controller, set remote contorl id as follows. 6.1. Setting id of md800m (1) press the [menu] button (2) select “system” with using [▶] button and press the [▷] or [▼] button (3) select “miscelleaneous” from the sub-menu l...

  • Page 17

    17 6.2. Selecting md800m if several edvrs are set with unique id numbers, they can be controlled with one remote controller. To select a specific edvr (md800m), keep pressing the id button of remote controller until a buzzer sounds during 2 seconds. Ote> because remote controller id is sixteen, edvr...

  • Page 18

    18 7. Md800m configuration 7.1. Basic configuration 7.2. Advanced configuration.

  • Page 19

    19 7.3. External storage & back up configuration 7.4. Internet/ intranet configuration.

  • Page 20

    20 8. Edvr md800m basic setting 8.1. Viewing image when power is on, md800m starts automatically and images are displayed in basic 9division screen after the booting. Ote> if user password is set, a prompt for entering the password will appear. Facotry default is reserved as not responding key pad o...

  • Page 21

    21 8.2. Setting date & time (1) press [menu] button and select “quick setup” tab. (2) select “date/time” using the [▷] or [▼] and press [exit] button. 8.2.1. Time zone (1) select “time zone” using the [◀/▶] or [▲/▼] buton and press [▷] to configure. (2) select time zone using the [◀/▶] button and pr...

  • Page 22

    22 8.2.4. Time format (1) select “time format” using the [◀/▶] or [▲/▼] button and press [▷] button.. (2) two time formats are available; ‘dd/mm/yyyy,’ ‘mm/dd/yyyy’, ‘yyyy/mm/dd’; select a value using [▲/▼] buttons and press the [exit] button when it is finished. (factory default is set as ‘mm/dd/yy...

  • Page 23

    23 8.3. Setting recording condition recording conditions under the “quick setup” menu tab apply the same values to all analog channels 1~8. All settings are applied for 24 hours/ day regardless of the value set for “time schedule” or “alarm rec.” (1) press [menu] button and select “quick setup” when...

  • Page 24

    24 8.3.2. Recording speed/quality (1) select “recording speed/ quality using [▲/▼] buttons and press [▷]. (2) select a value using the[◀/▶] button. Press the [exit] button when it is finished. 8.3.3. Speed(ips) when “recording speed/quality” is set as” custom”, values can be set manually. (1) select...

  • Page 25

    25 9. Connecting and configuring dio ports ote> wire handling trimming wire when connecting a wire to a terminal block, follow the instructions below. Note the different types of wire that can be used. Standard wire : peel off the wiring, cover 8~10mm and solder it. Wire gage should be awg 22~26. So...

  • Page 26

    26 9.1.2. Connecting sensor input connect s1 ~ s8 with referring to the followings. It shows to connect a dry contact (please refer to “ote> wire handling” on page 27). When connecting a non-dry contact type of sensor (e.G. Open collector output) please contact webgate’s customer support team..

  • Page 27

    27 9.1.3. Configuring sensor at osd menu (1) press the[menu] button and select “alarm source”. (2) press [▷] or [▼] button to move to sub-menu, select “sensor” and press [▷]. 9.1.3.1. Global use when selecting all 8 sensors simultaneously, which can be selected as “do not use”(off). “normal open” (n...

  • Page 28

    28 ote> 1. Configuration a sensor is to set on/off usage and type. 2. Please refer to “alarm rec” for saving and “alarm act” for relay-out on the “edvr user’s guide” 9.2. Connecting & configuring relay out 9.2.1. Specifications in order to run relay output of edvr md800m normally, the following cond...

  • Page 29

    29 9.2.2. Connecting relay out connect r1 ~ r4 with referring to the followings, it shows how to connect a warming light. Please refer to “ ote> wire handling” on page 25..

  • Page 30

    30 9.2.3. Configuring relay out as osd menu. Relay can run by sensor or md and its condition can be set differently according to schedule. When using the [relay] button + [number] button on the front panel or control center lite-d s/w, relay can be operated from remote site. Ote> please refer to the...

  • Page 31

    31 9.3. Connecting serial port 9.3.1. Configuring serial ports for pan/tilt/zoom the md800m have most major ptz protocols already pre-programmed. Makes and models not supported can still be controlled using the transparent protocol. For a list of supported protocols, refer to the list on the osd con...

  • Page 32

    32 9.3.2.1. Diagram of com1(rs232) 9.3.2.2. Diagram of com2(rs485) 9.3.2.3. Diagram of com3(rs485).

  • Page 33

    33 9.3.3. Configuring serial configure ptz com ports and available models at “system/ serial setup” in md800m. After completing serial setup, configure base address or port for each channel at “ camera menu” tab. When connecting ptz devices to several cameras, be sure base address matches address fo...

  • Page 34

    34 9.4. Connecting external device with serial port 9.4.1. Connecting text inout device (atm / pos / access control) the md800m can record text data received from pos/atm through the com/rs232 serial port. Connect to com1/rs232 (9pin d-sub) of md800m and configure the “serial setup” sub-menu under t...

  • Page 35

    35 9.4.2. Configuring serial setup (com1) at osd menu (1) set the “system” in osd menu and move to “serial setup” menu. (2) select com in “serial setup”, set devices as “text”. (3) set baud rate/ parity/ stop bit with referring to manual of the connected external device..

  • Page 36

    36 9.4.3. Configuring text (1) select the “alarm source” menu among osd menus. (2) select the “text” and set each value. Ote> before installing any external device, consult with the local webgate distributor. Some external devices may not be compatible with the edvr..

  • Page 37

    37 9.5. Connecting usb device usb port can be used to copy up to 1 minute of images to a usb flash memory disk. When connecting usb device, do not exceed the rated values of usb device as below; usb spec. Ver 1.1 (max 12m bps) available device usb memory stick, output voltage/current max. 200ma per ...

  • Page 38

    38 9.6. Connecting video in/output.

  • Page 39

    39 10. Connecting external storage 10.1. Esata port md800m have two esata ports (rear: 1-ports) for external storage device interface. Ote> some esata may not be recognized by the md800m according to the method. Before purchasing, please consult with the local distributor. 10.2. Connecting esata dev...

  • Page 40

    40 10.3. Available hdd it is recommended to use following hdd models with the md800m. If a non-recommended hdd is used, webgate inc. Will guarantee the warranty. 10.4. Registering & formating hdd “disk manager” will automatically run on start-up installing a hdd as below; if “disk manager” deos not ...

  • Page 41

    41 (9) shut down “disk manager” by pressing [exit] button. 11. Etwork monitoring & managing md800m can be accessed, controlled, and managed from remote site using pc via internet/ intranet, which is same way as local access for controlling & monitoring features. 11.1. Connecting ethernet (1) turn of...

  • Page 42

    42 11.2. Configuring etwork infomraiton of md800m the following description is based on ethernet connection. For more detailed information on the network setting page and way of using xdsl, please refer “edvr users’ guide”. (1) press [menu] button (2) select “system” using the [◀/▶] buttons and pres...

  • Page 43

    43 12. Using control center lite control center list is a dvr management software and it makes dvr installtion & setting more easier throguth a pc which is connected with dvr in network. All configuration could be handled in osd menu of dvr without a pc, however, control center lite makes the comple...

  • Page 44

    44 3> select components which wish to install and press “next” button. “wesp sdk” must be installed. 4>.Click the “install” button after selecting a directory to be insatalled. 12.3. Log-in enter user name, password and press “ok” button. The factory default value : user name:administrator, password...

  • Page 45

    45 12.4. Configuration tool click the icon on the desk top to run “control center lite configuration tool”. 12.5. Monitor * max. 5 users could be connected simultaneously in one unit of md800m. Click the icon on the desk top to run “control center lite monitor”..

  • Page 46

    46 12.6. Playback * max. 2 user could be connected for playback in one unit of md800m. Click the icon on the desk top to run “control center lite playback”..

  • Page 47

    47 appendix appedix appedix.

  • Page 48

    48 #1. Hdd #1.1. Fundamental notions & terms edvr storing constructure (vfs2) edvr series has a peculiar storing constructure, and its features are as follows. (1) it is possible to connect 2 sets of hdd internally (internal, ata interface) and 63 sets of hdd externally (external, 1 port of esata). ...

  • Page 49

    49.

  • Page 50

    50 (2) hdd type at disk manager [r] available recording status [v] connected and formatted as edvr’s file system. If using ‘add used’ command, it will be changed to [r]. There is no need to format. [f] connected but not available edvr’s file system. After using ‘add’, need to format for making as [r...

  • Page 51

    51 #1.2. Installing hdd compatible hdd it is recommended to use the following hdd models with the md800m. If a non-recommended hdd is used, webgate inc. Will not guarantee the warranty. Installation and extension of internal hdd-rack hdd in case of installation/adding or exchange hdd, follow the pro...

  • Page 52

    52.

  • Page 53

    53 (3) remove 4 hdd bracket screws to take out hdd bracket. (4) fix the hdd into hdd bracket with provided screws. Assemble an earth cable with hdd. Ote> > > > when assembling a hdd, the back side of hdd should be with hdd bracket shown as above figure..

  • Page 54

    54 (5) fix the assembled hdd and earth cable into case with screws. (6) assemble the top cover. Ote> caution for hdd management 1. Replacing ‘slave’ hdd of internal 2 hdds causes permanent data loss in the slave hdd. 2. Master hdd has all the index of stored data including ‘slave’ hdd. Corruption on...

  • Page 55

    55 expending external hdd (when using internal hdd as primary disk) md800m use esata as external storage device interface, and has one port to support it. Using this port, maximum 8tb storage is installable. Ote> 1. Some esata ports may not be recognized by the md800m. Before purchasing, consult the...

  • Page 56

    56 when using disk farm the following description is when md800m has internal primary disk and 1 sets of esata hdd. (1) when external hdd farm is connected to esata port, “disk manager” runs automatically. If not, run it manually in “menu utilitydisk manager”. (2) select a second hdd of [f] ext. Pre...

  • Page 57

    57 when using raid the following description is when md800m has internal primary disk and 1 set of ieee1394 raid. Ote raid> even though several hdds are connected to raid, md800m will recognize them as only one hdd. For connection and setup of raid, please refer to the manual of related device. (1) ...

  • Page 58

    58 replacing hdd checking hdd md800m file system (vfs2) sensors bad sector automatically, and the sensored bad sector is not used. The following means when hdd is broken or has some problem in connection. (1) when playback is stopped or md800m is rebooted in specific playback range or image searchin...

  • Page 59

    59 (5) set backup range and press the “start” button after selecting backup hdd. Ote> 1. Backup hdd should be formatted as fat32 type. 2. Backup data can be replayed with specific s/w in pc such as control center lite-d or miniplayer. 3. Backup data is made as “*.Re4” file and recognized as cd-r 700...

  • Page 60

    60 caution in using hdd for handling or guaranteeing hdd, webgate follows hdd guaranty condition. Webgate doesn’t bear the responsibility about data loss by user’s mistake in operating. Ote> it supports only dvd backup. Cd backup will be supported later. For the details, please contact to local dist...

  • Page 61

    61 #2. Using cd-rom components of cd- rom disc installation guide : edvr md800m installation guide user’s guide : edvr md800m user’s guide control center lite-d : control center lite-d user’s guide (control center lite-d remote management program) acrobat reader : version 7.0 preparation to read man...

  • Page 62

    62 #3. How to recognize manufacturing date the manufacturing date by webgate can be recognized by s/n(serial number) attached at the each product. S/ : serial umber management number for each webgate product to combine twelve alphabet character and digit including model name, manufacturing year/mont...

  • Page 63

    63 #4. Specification general cpu 32bit risc processor flash memory 32mb main memory 128mb os embedded linux video channel 8ch. Analog video inputs via bnc connector ntsc or pal video format are supported (auto detect) storage device int.: 2 hdd bays including ext: 1 esata connection ports supports d...

  • Page 64

    64 schedule recording daily : day / night / four-segment time frame weekly : weekdays / weekends, exception days conditions : normal / event text data recording pos/atm transaction information archived along with corresponding video data manual recording manual(emergency) record triggered by font ke...

  • Page 65

    65 data backup/expansion/copy data backup external hdd(esata) internal cd-r/dvd-r backup reminder 5~ 95% alarm avi copy external usb memory disk(usb 1.1 compatible) on usb port input/output video output 2 cvbs main monitor 1 vga audio 1 input : line-in, 1 vpp 1 output : line-out, 1vpp buzzer softwar...

  • Page 66

    66 mechanical dimension (wⅹ ⅹ ⅹ ⅹdⅹ ⅹ ⅹ ⅹh) 420.0 x 294.0 x 98.0 weight 5.5 kg (with one hdd).

  • Page 67

    67 webgate inc. 6f, hanlim venture town bldg., 689-6, geumjeong-dong, gunpo-si, gyeonggi-do, korea (435-862) tel : (82-31) 428-9300 fax : (82-31) 455-3955 sales@webgateinc.Com www.Webgateinc.Com the contents of this manual can be modified in accordance with firmware or software upgrade. In the inter...