Summary of W50 R
Page 1
Operating manual edition 1 weda w 50 r 32 utg. 3 20091007 110 v / 230 v - 60hz 230 v - 50hz.
Page 2
Weda w 50 r table of content 1 weda poolcleaner ab and pool vacuums 2 delivery specifications 3 technical specifications 4 installation 5 operating instructions 6 service and maintenance 7 control box and electrical schematics.
Page 3
Weda w 50 r 1.Weda poolcleaner ab and pool vacuums weda poolcleaner ab has produced pool vacuums for public pools since the mid-1970´s. Today the products are distributed world wide through own subsidiaries and a distributor network. The product program consists of fully-automatic or semi-automatic ...
Page 4
Weda w 50 r 2. Delivery specification pool vacuum with 25 or 40 m (75 or 120 ft) floating cable (umbilical) filter bag, 120 micron mesh control box for wall mounting with power cable four channel radio remote control. Tool kit manuals and other documentation optional equipment 1: trolley for cleaner...
Page 5
Weda w 50 r 3.3 floating cable (umbilical) dimension and length Ø 1 inch , 75 or 120 ft Ø25 mm, 25 or 40 m 4 .Installation the vacuum cleaner must be connected through a ground fault circuit interrupter (gfci) or earth leakage circuit breaker (elcb) or a residual current device (rcd) having a rated ...
Page 6
Weda w 50 r 5 operating instructions 5.1 the control box the control panel has the following controls and options: switch on/off (with light) switch manual/automatic on the bottom of the control box you find: the power cable connection (connect via a gfci or elcb or rcd) reset for the over current p...
Page 7
Weda w 50 r 5.2 the radio remote control the remote control overrides the automatic function the remote control is a 4 channel radio transmitter with the following control functions: 1. Forwards. Press once for forward movement to stop press forward button again or backward button. 2. Backwards. Pre...
Page 8
Weda w 50 r 5.4 manual cleaning make sure that the swich on the conrol box is set to manual. Start by driving the pool vacuum around the walls in the pool and clean thereafter the entire pool bottom at any pattern you may prefer. 5.5 automatic cleaning use the radio remote control to drive the pool ...
Page 9
Weda w 50 r 6 service and maintenance 6.1. Routine maintenance after use check that the drive tracks are free from obstacles like hair, chewing gum, rubber bands or whatever else that may have got stuck there during cleaning. Flush the cleaner with fresh water. Make sure to reach also under the cove...
Page 10
Weda w 50 r 6.4 replacing the drive tracks, brusharms and belts loosen the domed nuts (12) and lift off the covers (11). Loosen the wheel bolts (4), the track tension bolts (9 and 10) and the front shaft (8). Pull off the wheels and the tracks. Now the belts and the arms may be replaced. Reassemble ...
Page 11
Weda w 50 r 6.5 note do not drive the pool vacuum outside the pool water for more than 5 minutes per hour. The vacuum and the floating cable are cooled by the pool water. Use only weda original parts for service at all times. One incorrectly used o-ring may cause costly damage to the pool vacuum. Do...
Page 12
? ! Weda w 50 r 6.7 q and a´s problem reason / remedy the vacuum does not pump or move 1. Fuse broken/ replace fuse 2. Gfci, efcb or rcd has shut off the power. 3.Over current relay has released and not reset/reset the relay 4.Impeller blocked. Release obstacle 5.Contactor burnt/ replace. 6.Stator b...