1. DL manuals
  2. Weider
  3. Home Gym
  4. 265
  5. User Manual

Weider 265 User Manual

Other manuals for 265: User Manual
Manual is about: Weider 265 Home Gym USER'S MANUAL WESY19611

Summary of 265

  • Page 1

    User’s manual model no. Wesy19610 serial no. Write the serial number in the space above for reference. Patent pending caution read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Serial number decal visit our website at www.Weider...

  • Page 2: Table of Contents

    2 important precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 a...

  • Page 3: Warning:

    3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. Use the weight system only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions. 3....

  • Page 4: Before You Begin

    Before you begin 4 assembled dimensions: height: 76 in. Width: 37 in. Length: 48 in. Leg press plate rocker arm low pulley station foot plate high pulley station lat bar leg lever butterfly arms press arm weight stack resistance cylinder seat backrest warning decal 1 warning decal 3 warning decal 4 ...

  • Page 5: Assembly

    Make sure you have the following tools: • two adjustable wrenches • one standard screwdriver • one phillips screwdriver • one rubber mallet • you will also need grease or petroleum jelly, and a small amount of soapy water. Note: assembly will be more convenient if you have a socket set, a set of ope...

  • Page 6

    6 2 42 3 1 4 1 56 76 51 5 94 3 51 51 1 76 4 4 16 1 1. Before beginning assembly, make sure that you have read and understand the information on page 5. Press a 2” square outer cap (51) onto each end of the stabilizer (5). Press a 2” square outer cap (51) onto the base (4). Press a 2” square inner ca...

  • Page 7

    7 5. Slide a weight bumper (95) onto each weight guide (62). Lubricate the two outer holes in each of the weights (25). Slide the weights onto the weight guides (62). Make sure that the weights are turned so the pin grooves are on the indicated side. 6. Place a piece of cardboard under each weight g...

  • Page 8

    8 8. Press a 1 3/4” square inner cap (44) into the top of a press arm (46). Press a 1” round inner cap (49) into the handle on the press arm. Attach the press arm (46) to one side of the press frame (17) with two 5/16” x 2 1/2” bolts (22) and two 5/16” nylon locknuts (3). Assemble the other press ar...

  • Page 9

    11. Press a 1 3/4” square inner cap (44) into the seat frame (36). Attach a bumper (73) to the seat frame with a #8 x 3/4” tap screw (65). Slide the seat frame (36) onto the 5/16” x 2 1/2” carriage bolts (1) in the base (4). See the inset drawing. The indicated bracket on the seat frame must be behi...

  • Page 10

    14. During steps 15 through 44, refer to the cable diagrams on page 23 of this manual to verify proper cable routing. Before beginning this sec- tion, identify the high cable (23), the low cable (19), the press cable (58), and the resistance cable (27) by comparing the ends and lengths of the cables...

  • Page 11

    11 18. Route the high cable (23) around a “v”- pulley (6). Attach the pulley and a long cable trap (50) to the indicated bracket on the rear upright (56) with a 3/8” x 2 1/2” bolt (7) and a 3/8” nylon locknut (21). Do not tighten the nylon locknut yet. Make sure that the cable trap is turned to hold...

  • Page 12

    12 22. Insert the end of the high cable (23) into the open end of the weight tube (63). Slide the plastic stabilizer (67) onto a 5/16” x 1 3/4” bolt (72). Then, insert the bolt into the hole near the top of the weight tube and through the end of the high cable. Tighten a 5/16” nylon locknut (3) onto...

  • Page 13

    13 25. Remove the 3/8” x 2” bolt (12), the 3/8” nylon locknut (21), the 4 1/2” pulley (84), and the metal cable trap (97) from the lower ends of the pulley plates (20). Wrap the low cable (19) over the pulley, and reattach the pulley and the metal cable trap to the pulley plates with the bolt and th...

  • Page 14

    14 29. Wrap the press cable (58) around a “v”-pulley (6). Attach the “v”-pulley and a long cable trap (50) inside of the bracket on the seat frame (36) with a 3/8” x 2 1/2” bolt (7) and a 3/8” nylon locknut (21). Make sure that the cable trap is turned to hold the cable in place. 30. Wrap the press ...

  • Page 15

    58 58 57 57 10 2 2 15 15 33. Route the press cable (58) between the indicat- ed 3 1/2” pulley (15) and the cable trap (66) attached to the rear upright (56). Make sure that the cable trap is turned to hold the cable in place. Properly tighten the 3/8” nylon locknut (21). 34. Attach the end of the pr...

  • Page 16

    15 15 16 4 12 27 21 15 37. Identify the resistance cable (27). Thread the 1/2” plain nut (101) onto the bolt at the end of the resistance cable (27). Thread the resistance cable part way into the lower end of the weight tube (63). Tighten the plane nut against the weight tube. 38. Wrap the resistanc...

  • Page 17

    17 98 4 27 41. Attach two 3 1/2” pulleys (15) and two cable traps (66) to the end of the resistance bracket (35) as shown with a 3/8” x 3” bolt (93) and a 3/8” nylon jamnut (33). Do not tighten the nylon jamnut yet. Make sure the pulleys and cable traps are oriented as shown. Route the resistance ca...

  • Page 18

    18 47 48 79 22 8 8 3 end must slant this way 32 40 78 320 lb. Leg press 34 34 34 30 30 29 80 30 28 45. Attach the backrest (41) to the front upright (42) with two 1/4” x 2 1/2” screws (43) and two 1/4” washers (10). 46. Insert the 1/4” x 2 1/2” carriage bolt (38) into the center hole in the seat pla...

  • Page 19: Adjustments

    19 the instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise. Impor- tant: when attaching the lat bar or nylon strap, make sure that the attachments are in t...

  • Page 20: Warning:

    20 attaching the lat bar or nylon strap to the pulley stations attach the lat bar (54) to the high cable (23) with a cable clip (53). For some exercises, the chain (52) should be attached between the lat bar and the high cable with two cable clips. Adjust the length of the chain between the lat bar ...

  • Page 21

    21 tightening the cables woven cable, the type of cable used on the weight system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened. Refer to drawing 1. One way to remove slack from the cables is to tighten the resi...

  • Page 22: Weight Resistance Chart

    22 weight resistance chart leg lever butterfly arms low pulley leg pressarm presshigh pulley no. Of w eights handle position 33 86 96 102 136 54 92 106 124 152 66 116 122 142 164 84 106 138 154 180 110 126 152 168 204 * 44 64 78 94 39 55 75 89 108 51 68 90 104 121 63 78 102 115 131 76 92 112 124 144...

  • Page 23: Cable Diagrams

    23 4 5 4 3 4 3 2 3 2 2 7 7 8 6 5 4 3 2 6 1—low pulley 1—leg lever 1—high pulley high cable (23) resistance cable (27) 9—weight stack 8—long “u”-bracket 5—rear upright bracket 1—weight stack 8—wide bracket press cable (58) low cable (19) 5 6 7 cable diagrams the cable diagrams below show the proper r...

  • Page 24

    1/4" washer (10) 5/16" washer (8) 3/8" washer (9) 1/4" x 2 1/2" screw (43) 5/16" x 1 3/4" bolt (72) 3/8" nylon locknut (21) 3/8" nylon jam nut (33) 5/16" nylon jamnut (99) 1/4" x 2 1/2" carriage bolt (38) 5/16" x 2 1/2" carriage bolt (1) 3/8" x 2" bolt (12) 5/16" x 2 1/2" bolt (22) 3/8" x 2 1/2" bol...

  • Page 25

    #8 x 3/4" tap screw (65) 3/8" x 3" bolt (93) 3/8" x 1 1/4" bolt (83) 3/8" x 3" grade 5 bolt (98) 5/16" x 1 1/4" bolt (92) 5/16" x 2 3/4" carriage bolt (94) 3/8" x 3 1/2" bolt (16) 3/8" x 3 3/4" bolt (71) 5/16" x 6" bolt (60) 5/16" x 2 3/4" bolt (11) 3/8" x 3 1/4" bolt (68) 3/8" x 3 1/2" bolt (16) 3/...

  • Page 26

    1" round inner cap (49) 1" round cover cap (70) 3/4" round inner cap (34) 1" inner cap (81) 1" retainer (69) 1/2" x 3/4" spacer (82) 1/2" x 7/8" spacer (100) 1/2" x 1/2" spacer (96) 5/8" x 7/8" spacer (61) 1 3/4" square inner cap (44) 2" square inner cap (76) 2" square outer cap (51) 1" x 7/8" plast...

  • Page 27

    Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key no. Qty. Description key no. Qty. Description 1 4 5/16” x 2 1/2” carriage bolt 2 2 1/4” nylon locknut 3 20 5/16” nylon locknut 4 1 base 5 1 stabilizer 6 5 “v”-pulley 7 5 3/8” x 2 1/2” bolt 8 4 5/16” ...

  • Page 28

    10 43 41 23 3 63 26 25 27 31 31 44 49 46 46 49 44 22 3 21 66 15 59 75 21 16 9 60 3 62 60 3 44 71 23 15 12 81 44 15 12 3 11 3 21 12 6 66 44 21 21 7 6 15 15 93 66 33 3 15 64 15 76 21 15 15 12 68 21 51 15 15 33 3 3 21 12 98 16 42 56 1 51 51 94 1 76 4 44 18 38 37 36 3 10 24 10 2 30 34 50 6 21 7 3 3 73 6...

  • Page 29: Ordering Replacement Parts

    To order replacement parts, call our customer service department toll-free at 1-800-999-3756, monday through friday, 6 a.M. Until 6 p.M. Mountain time (excluding holidays). To help us assist you, please be prepared to give the following information: • the model number of the product (wesy19610) • th...