1. DL manuals
  2. Weider
  3. Home Gym
  4. 831.159833
  5. User Manual

Weider 831.159833 User Manual

Manual is about: WEIGHT SYSTEM EXERCISER

Summary of 831.159833

  • Page 1

    Caution read all precautions and instruc- tions in this manual before using this equipment. Save this manu- al for future reference. Weight system exerciser user’s manual model no. 831.159833 serial no. Write the serial number in the space above for reference. Serial number decal (under seat) sears,...

  • Page 2: Table of Contents

    2 table of contents important precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 3: Important Precautions

    3 important precautions warning : to reduce the risk of serious injury, read the following important precautions before using the weight system. 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensu...

  • Page 4: Before You Begin

    4 assembled dimensions: height: 77 in. Width: 80 in. Depth: 59 in. Low pulley station foot plate leg lever press arm backrest curl pad butterfly arm ab pulley station weight stack leg press lever thank you for selecting the innovative and versatile weider ® pro power stack weight system. The weight ...

  • Page 5: Assembly

    5 assembly make sure that you have the following tools: • two adjustable wrenches • one standard screwdriver • one phillips screwdriver • one rubber mallet • you will also need grease or petroleum jelly, a small amount of soapy water, and masking tape. Note: assembly will be more convenient if you h...

  • Page 6: Frame Assembly

    1. Before beginning, be sure that you have read and understood the information on page 5. Locate and open the parts bag labeled “frame assembly.” press a 50mm square inner cap (67) into each end of the butterfly base (1). Insert four m8 x 61mm carriage bolts (75) and an m10 x 89mm carriage bolt (95)...

  • Page 7

    4. Slide the butterfly upright (4) over the indicated m8 x 61mm carriage bolts (75) in the butterfly base (1). Hand tighten two m8 nylon locknuts (86) onto the bolts. Do not tighten the locknuts yet. 4 7 5. Press three 50mm square inner caps (67) into the butterfly top frame (7). Attach the butterfl...

  • Page 8

    7 8. Press a 25mm square inner cap (69) into the small tube on the press upright (5). Slide the press upright (5) over the indicated m8 x 61mm carriage bolts (75) in the press base (3). Hand tighten two m8 nylon locknuts (86) onto the bolts. Do not tighten the locknuts yet. Slide the upright support...

  • Page 9

    9 10. Press a 50mm square inner cap (67) into the press top frame (9). Attach the press top frame (9) to the indicated bracket at the top of the press upright (5) with two m8 x 66mm bolts (89), a medium support plate (109), and two m8 nylon locknuts (86). Do not tighten the locknuts yet. 11. Identif...

  • Page 10

    10 13. Slide six weights (41) onto the right weight guides (26). Make sure the weights are turned so the pin grooves are on the bottom. Press a weight tube bumper (45) into the lower end of the short weight tube (44). Slide the short weight tube into the center holes in the weights (41). Lubricate t...

  • Page 11

    11 105 92 29 28 67 8 90 90 90 26 27 4 7 5 8 9 28 5 77 92 35 15 16 38 29 105 90 90 90 15. Press a 50mm square inner cap (67) into the center top frame (8). Place the center top frame on the indicated brackets on the uprights (4, 5). Note: the tops of the four weight guides (26, 27) must be behind the...

  • Page 12: Arm Assembly

    12 20. See the inset drawing. Press a plastic bushing (60) onto each welded tube on the press frame (17). Slide the press frame into place on the press base (3). Note: this will be a tight fit; the plastic bushings should fit onto each end of the welded tubes in the base. Lubricate the m10 x 207mm b...

  • Page 13: Cable Assembly

    13 23 86 20 84 73 bracket 24 4 114 90 73 37 34 22. Identify the right and left butterfly arms (19, 20) by the positions of the welded brackets. Press a 45mm square inner cap (68) into each end of the right butterfly arm (19). Wet the lower end of the butterfly arm with soapy water. Slide a large foa...

  • Page 14

    14 26. Remove another “v”-pulley (34) from the bag labeled “pulley bag 2.” wrap the butterfly cable (73) over the “v”-pulley (34). Attach the “v”-pulley and a long cable trap (37) to the bracket on the back of the butterfly upright (4) with an m10 x 58mm bolt (114) and an m10 nylon locknut (90). Mak...

  • Page 15

    32. Identify the ab cable (74). It is approximately 226 1/2” long, and it has a ball on one end and an eyelet on the other. Wrap the ab cable (74) over a 90mm pulley (35) as shown. Place two pulley covers (39) over the pulley, so that the large tabs are on the indicated side. Attach the pulley and p...

  • Page 16

    16 34. Wrap the ab cable (74) over a 90mm pulley (35) in the direction shown. Attach the pulley to the double “u”-bracket (31) with an m10 x 45mm bolt (94) and an m10 nylon locknut (90). 33. Wrap the ab cable (74) under a 90mm pulley (35). Attach the pulley and a cable trap (38) to the top hole in t...

  • Page 17

    17 38 93 32 74 35 38 38. Wrap the ab cable (74) over a 90mm pulley (35) in the direction shown. Attach the pulley and a cable trap (38) to the second set of holes from the bottom in the indicated pair of pulley plates (32) with an m10 x 48mm bolt (93) and an m10 nylon locknut (90). Make sure the cab...

  • Page 18

    18 41. Locate the weight plate (48) that is attached to the bottom of the bottom weight (47). See the inset drawing. Attach the end of the ab cable (74) to the bottom of the weight plate (48) with an m10 x 45mm bolt (94) and an m10 nylon locknut (90). 41 48 94 90 74 47 42. Identify the low cable (71...

  • Page 19

    19 45. Remove the m10 nylon locknut (90) used in step 43. Wrap the low cable (71) under a 90mm pulley (35). Attach the pulley and a cable trap (38) to the m10 x 121mm bolt (102) used in step 43 with the m10 nylon locknut (90). Make sure the cable trap is positioned to hold the cable in the groove of...

  • Page 20

    20 49. Wrap the press cable (72) under a 90mm pulley (35). Attach the pulley and a cable trap (38) to the indicated hole in the press upright (5) with an m10 x 93mm bolt (85), an m10 washer (97) and an m10 nylon locknut (90). Make sure the cable trap is positioned to hold the cable in the groove of ...

  • Page 21

    21 53. Wrap the press cable (72) around a 90mm pulley (35) in the direction shown. Attach the pulley and a cable trap (38) to the indicated hole on the right side of the press upright (5) with an m10 x 121mm bolt (102) and an m10 nylon locknut (90). Note: thread the locknut only two turns onto the b...

  • Page 22

    22 57. Remove the m10 nylon locknut (90) used in step 53. Route the press cable (72) through the press frame (17). Wrap the press cable (72) under a 90mm pulley (35). Slide a cable trap (38) and the pulley onto the m10 x 121mm bolt (102) in the bottom of the press upright (5). Properly tighten the m...

  • Page 23: Seat Assembly

    23 61. Attach the press cable (72) to the remaining “u”- bracket (33) with an m8 washer (100) and an m8 nylon locknut (86). Note: do not completely tighten the locknut; it should be threaded onto the cable so that only two threads show past the locknut (see the inset drawing). Attach the “u”-bracket...

  • Page 24

    24 65. Press a 45mm square inner cap (68) into the indicated end of the adjustment tube (15). Orient the leg press plate (16) and adjustment tube (15) as shown in the inset drawing. Attach the adjustment tube to the leg press plate (16) with an m8 x 58mm bolt (110), two m8 washers (100), and an m8 n...

  • Page 25: Adjustments

    25 adjusting the leg press plate to adjust the position of the leg press plate (16), pull out the adjustment pin (40) and slide the adjustment tube (15) either backward or forward in the bracket on the leg press lever (14). Line up one of the adjustment holes in the adjustment tube with the hole in ...

  • Page 26

    26 81 47 41 41 changing the weight setting to change the setting of a weight stack, insert a weight pin (81) under the desired weight (41). Insert the weight pin so that the bent end touches the weight stack. Turn the bent end down. To use the bottom weight (47) with the press arms or the leg press,...

  • Page 27: Weight Resistance Chart

    27 weight resistance chart the chart below shows the approximate weight resistance at each exercise station. “left top” and “right top” refer to the 6 lb. Top weights. “bottom” refers to the 12.5 lb. Bottom weight. The other numbers refer to the 12.5 lb. Weight plates. Weight resistance shown for th...

  • Page 28

    28 the threaded ends on the rear cable (70) and the press cable (72) attached to the weight stacks can be used to tighten the cables. To tighten the rear cable (70), remove the m8 x 45mm bolt (96) and the m8 nylon locknut (86) from the “u”-bracket (33) and the short weight tube (44). Tighten the m8 ...

  • Page 29

    29 97 12 72 92 34 90 97 5 72 85 34 5 90 37 37 slack can be removed from the press cable (72) by moving the “v”-pulley (34) attached to the press seat frame (12) closer to the press upright (5). Remove the m10 x 93mm bolt (85), m10 washer (97), and m10 nylon locknut (90) from the press seat frame (12...

  • Page 30: Cable Diagrams

    Cable diagrams the cable diagrams below and on the next page show the proper routing of the rear cable (70), the low cable (71), the press cable (72), the butterfly cable (73), and the ab cable (74). The numbers show the correct route for each cable. Make sure that the cables are routed correctly, t...

  • Page 31

    Low cable (71) 5 4 3 1 2 6 7 3 1 8 9 10 11 5 6 2 1 4 1 2 4 3 2 3 butterfly cable (73) 5 rear cable (70) 31 4 ab cable (74).

  • Page 32

    M10 x 63mm carriage bolt (76) m6 x 65mm bolt (79) m4 x 25mm screw (80) m10 x 67mm bolt (82) m10 nylon locknut (90) m8 nylon locknut (86) m6 nylon locknut (103) m8 x 66mm bolt (89) m10 x 69mm bolt (92) m10 x 48mm bolt (93) m10 x 45mm bolt (94) m8 x 45mm bolt (96) m10 x 58mm bolt (114) m8 x 20mm shoul...

  • Page 33

    M10 x 97mm bolt (77) m10 x 93mm bolt (85) m10 x 76mm bolt (88) m6 x 62mm carriage bolt (91) m10 x 91mm bolt (101) m10 x 121mm bolt (102) m10 x 72mm bolt (105) m10 x 207mm bolt (106) m10 x 92mm carriage bolt (112) m10 x 78mm bolt (107) m10 x 100mm bolt (115) m10 x 84mm bolt (78) m10 x 89mm carriage b...

  • Page 34

    25mm retainer (54) 25mm round cover cap (55) 25mm round inner cap (66) 19mm round inner cap (64) 50mm square inner cap (67) 45mm square inner cap (68) 25mm square inner cap (69).

  • Page 35

    Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. 1 1 butterfly base 2 1 center base 3 1 press base 4 1 butterfly upright 5 1 press upright 6 1 upright support 7 1 butterfly top frame 8 1 center top frame 9 1 press top frame 10 1 butterfly seat frame 11...

  • Page 36

    62 59 62 62 5 6 35 38 38 35 35 38 35 35 38 37 34 18 18 60 35 38 38 32 32 23 12 34 37 38 38 38 38 14 40 35 35 61 61 109 50 15 16 47 41 41 27 46 26 46 42 44 45 33 35 17 9 35 29 38 35 109 32 32 38 35 35 38 36 36 28 28 8 34 34 37 37 4 39 39 35 25 21 22 23 10 11 50 52 49 64 35 35 35 38 38 38 109 1 56 57 ...

  • Page 37: Full 90-Day Warranty

    Part no. 202725 r1203a printed in china © 2003 sears, roebuck and co. Full 90-day warranty for 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this weight system exerciser, contact the nearest sears service center throughout the united states and sear...