Weider 8510 User Manual - Important Precautions

Summary of 8510

  • Page 1

    User's manual questions? As a manufacturer, we are com- mitted to providing complete customer satisfaction. If you have questions, or find there are miss- ing or damaged parts, we will guarantee you complete satisfac- tion through direct assistance from our factory. To avoid unnecessary delays, plea...

  • Page 2: Table of Contents

    2 table of contents limited warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 important precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 3: Important Precautions

    3 1. It is the responsibility of the owner to ensure that all users of the home gym system are adequately informed of all precautions. 2. Read all instructions in this manual and in the accompanying literature before using the home gym system. 3. If you feel pain or dizziness at any time while exerc...

  • Page 4: Before You Begin

    4 before you begin assembled dimensions: height: 76 in. Width: 38 in. Length: 53 in. Foot plate low pulley station high pulley station lat bar leg lever butterfly arms press arm weight stack seat backrest weight pin thank you for selecting the versatile weider ¨ 8510 home gym system. The weider ¨ 85...

  • Page 5: Assembly

    5 assembly 1 56 high side of bracket 3 5 51 51 14 1 27 4 before beginning assembly, carefully read the following information and instructions: ¥ place all parts of the home gym system in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is comple...

  • Page 6

    6 frame assembl y 2. Slide the front upright (42) onto the 5/16Ó x 2 1/2Ó carriage bolts (1) in the base (4). Hand tighten a 5/16Ó nylon locknut (3) onto each carriage bolt. Do not tighten the nylon locknuts yet. Press a 1Ó square inner cap (65) into the front upright (42). 3. Press a 2Ó square inne...

  • Page 7

    7 frame assembl y arm assembl y 5. Press the weight tube bumper (64) into the end of the weight tube (63). Insert the weight tube into the stack of weights (25). Be sure that the pins on the weight tube are resting in the pin grooves in the upper weight. Lubricate the insides of the holes in the top...

  • Page 8

    8 arm assembl y 8. Press a 1 3/4Ó square inner cap (44) into the top of a press arm (46). Press a 1Ó round inner cap (49) into each end of the handle on the press arm. Attach the press arm to one side of the press frame (17) with two 5/16Ó x 2 1/2Ó bolts (22) and two 5/16Ó nylon locknuts (3). Assemb...

  • Page 9

    9 cable assembl y 11. During steps 11 through 25, refer to the cable diagram on page 20 of this manual to verify proper cable routing. Before begin- ning this section, identify the long cable (23) and the short cable (58) by comparing the lengths and ends of the cables. Important: while assembling t...

  • Page 10

    10 15. Route the long cable (23) around the ÒvÓ- pulley (6) on the right arm (48). Be sure that the cable is in the groove of the ÒvÓ- pulley and that the long cable trap (50) is turned to hold the cable in place. Tighten the 3/8Ó x 2 1/2Ó bolt (7) and the 3/8Ó nylon locknut (not shown). 16. Route t...

  • Page 11

    11 cable assembl y 19. Note: this assembly step shows how to complete the assembly of several pre- attached parts. The 5/8Ó x 9/16Ó spacer (73) has been pre- attached on the outside of the 3 1/2Ó low pulley (77) for shipping purposes. Remove the 3/8Ó nylon locknut (21), the spacer, and the pulley fr...

  • Page 12

    12 21. Route the short cable (58) around the 3 1/2Ó pulley (15) attached to the lower hole in the front upright (42). See the inset drawing. Be sure that the cable trap (66) is turned to hold the cable in place and that the cable is routed around the pulley as shown. Tighten the 3/8Ó nylon locknut (...

  • Page 13

    24. Attach the end of the short cable (58) to the long ÒuÓ-bracket (57) with a 1/4Ó nylon lock- nut (2) and a 1/4Ó flat washer (10). Do not completely tighten the nylon locknut. It should be threaded onto the end of the cable so only a couple of threads are showing above the nut, as shown in the ins...

  • Page 14

    14 26. Attach the backrest (41) to the front upright (42) with two 1/4Ó x 2 1/2Ó screws (43) and two 1/4Ó flat washers (10). 27. Press a 1 1/2Ó square inner cap (32) into the seat frame (36). Insert the 1/4Ó x 2Ó carriage bolt (38) into the center hole in the seat plate (37). Attach the seat plate t...

  • Page 15

    15 29. Rest the seat frame (36) on the indicated pin in the front upright (42). Attach the seat frame to the front upright with a 5/16Ó x 2 3/4Ó carriage bolt (14) and the seat knob (40). 30. Press 3/4Ó round inner caps (34) into the ends of both 12 1/2Ó pad tubes (28). Insert one 12 1/2Ó pad tube (...

  • Page 16

    16 31. Remove the decals from the decal sheet (not shown) and apply them to the home gym system in the loca- tions shown below. High pulley butterfly 8510 bench press low pulley leg curl leg extension 31 32. Make sure that all parts have been properly tightened. The use of the remaining parts will b...

  • Page 17: Adjustment

    17 adjustment the instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym system should be set up for each exercise. Important: when attaching the lat bar or nylon strap, make sure that the attach...

  • Page 18

    18 attaching and removing the seat set the bracket on the seat frame (36) onto the indi- cated pins on the front upright (42). Attach the seat frame to the front upright with the 5/16Ó x 2 3/4Ó carriage bolt (14) and the seat knob (40). For some exercises, the seat (13) must be removed. First, be su...

  • Page 19

    19 trouble-shooting and maintenance inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. Tightening the cables woven cable, the type of cabl...

  • Page 20: Cable Diagram

    20 cable diagram the cable diagram below shows the proper routing of the short cable (58) and the long cable (23). Use the diagram to be sure that the two cables and the cable traps have been assembled correctly. If the cables have not been correctly routed, the home gym system will not function pro...

  • Page 21: Notes

    21 notes.

  • Page 22

    22 note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. Part listÑmodel no. Wesy85101 r1196a key no. Qty. Description 1 2 5/16Ó x 2 1/2Ó carriage bolt 2 3 1/4Ó nylon locknut 3 17 5/16Ó nylon locknut 4 1 base 5 1 stabilizer 6 3 ÒvÓ-pulley 7 3 3/8Ó x 2 1/2Ó ...

  • Page 23

    23 11 11 8 8 55 27 12 15 44 15 71 23 27 21 44 21 3 61 60 3 56 15 12 2 57 58 21 3 5 51 14 19 26 51 25 64 63 76 9 21 3 3 4 1 27 65 15 71 41 10 43 3 21 6 50 7 42 7 50 6 21 69 70 69 70 47 48 44 45 44 45 13 40 38 37 18 32 28 30 34 10 2 24 36 30 34 14 33 3 29 34 30 28 8 3 49 49 46 32 30 34 35 49 49 46 22 ...

  • Page 24

    1Ó round inner cap (49)Ð6 1Ó round cover cap (70)Ð2 3/4Ó round inner cap (34)Ð4 1/2Ó x 3/4Ó spacer (61)Ñ2 5/16Ó x 2Ó eyebolt (35)Ñ1 1 1/2Ó square inner cap (32)Ñ2 1 3/4Ó square inner cap (44)Ð6 2Ó square inner cap (27)Ð3 2Ó square outer cap (51)Ð2 5/8Ó x 9/16Ó spacer (73)Ð1.

  • Page 25

    1" retainer (69)Ð4 3/8" x 2" bolt (12)Ð3 3/8" x 3 1/2" bolt (16)Ð1 3/8" x 2 1/2" bolt (7)Ð3 3/8" x 3 3/4" bolt (71)Ð4 ? ? ? @@@@@@@@e? N@h? ?@h? ? ? @?F? @?F? @?F? @?F? @?F? @?F? ?W2@@@@6x?? W.M?E?I/x? .Ygv/? ? W2@@@@6xe? 7@?E@??@e? 3=?C5?J5e? V4@0y?.Ye? ? @?W2@@6xe? @?7@?@?E?@e? 3x@lej5e? S@@@e.Ye?...

  • Page 26

    5/16" nylon locknut (3)Ð17 1/4" flat washer (10)Ð6 5/16" flat washer (8)Ð5 3/8" flat washer (9)Ð4 1/4" x 2 1/2" screw (43)Ð2 5/16" x 1 3/4" bolt (72)Ð1 3/8" nylon locknut (21)Ð12 1/4" x 2" screw (24)Ð1 1/4" nylon locknut (2)Ð3 5/16" x 2 1/2" carriage bolt (1)Ð2 5/16" x 2 3/4" carriage bolt (14)Ð3 1/...

  • Page 27: Ordering Replacement Parts

    Ordering replacement parts to order replacement parts, simply call our customer service department toll-free at 1-800-225-0653, monday through friday, 6 a.M. Until 6 p.M. Mountain time (excluding holidays). To help us assist you, please be pre- pared to give the following information: 1. The model n...