Weider 8520 User Manual - Table Of Contents

Other manuals for 8520: User Manual
Manual is about: Weider USER'S MANUAL Home Gym WESY85201

Summary of 8520

  • Page 1

    User's manual questions? As a manufacturer, we are com- mitted to providing complete customer satisfaction. If you have questions, or find there are miss- ing or damaged parts, we will guarantee you complete satisfac- tion through direct assistance from our factory. To avoid unnecessary delays, plea...

  • Page 2: Table Of Contents

    2 table of contents limited warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 important precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 3: Important Precautions

    3 1. It is the responsibility of the owner to ensure that all users of the home gym system are adequately informed of all precautions. 2. Read all instructions in this manual and in the accompanying literature before using the home gym system. 3. If you feel pain or dizziness at any time while exerc...

  • Page 4: Before You Begin

    4 before you begin assembled dimensions: height: 76 in. Width: 38 in. Length: 59 in. Leg press plate low pulley station foot plate high pulley station lat bar leg lever butterfly arms press arm weight stack seat backrest weight pin thank you for selecting the versatile weider ® 8520 home gym system....

  • Page 5: Assembly

    5 assembly 1 56 high side of bracket 3 5 51 51 14 1 4 1 before beginning assembly, carefully read the following information and instructions: • place all parts of the home gym system in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is complet...

  • Page 6

    6 frame assembl y 2. Slide the front upright (42) onto the 5/16” x 2 1/2” carriage bolts (1) in the base (4). Hand tighten a 5/16” nylon locknut (3) onto each carriage bolt. Do not tighten the nylon locknuts yet. 3. Press a 2” square inner cap (27) into each end of the top frame (55). Press a 1 3/4”...

  • Page 7

    7 frame assembl y arm assembl y 5. Press the weight tube bumper (64) into the end of the weight tube (63). Insert the weight tube into the stack of weights (25). Be sure that the pins on the weight tube are resting in the pin grooves in the upper weight. Lubricate the insides of the holes in the top...

  • Page 8

    8 arm assembl y 8. Press a 1 3/4” square inner cap (44) into the top of a press arm (46). Wet the handle on the press arm with soapy water. Slide a handgrip (31) onto the handle. Press a 1” round inner cap (49) into the other end of the handle. Attach the press arm to one side of the press frame (17...

  • Page 9

    11. Press a 1 3/4” square inner cap (44) into the seat frame (36). Attach a bumper (73) to the seat frame with a 1/2” tap screw (65). Slide the seat frame (36) onto the 5/16” x 2 1/2” carriage bolts (1) in the base (4). See the inset drawing. The bracket on the seat frame must be behind the press fr...

  • Page 10

    14. During steps 15 through 29, refer to the cable diagram on page 19 of this manual to verify proper cable routing. Before begin- ning this section, identify the long cable (23) and the short cable (58) by comparing the lengths of the cables. Important: while assembling the cables, do not overtight...

  • Page 11

    11 18. Route the long cable (23) around the “v”- pulley (6) on the right arm (48). Be sure that the cable is in the groove of the “v”- pulley and that the long cable trap (50) is turned to hold the cable in place. Tighten the 3/8” x 2 1/2” bolt (7) and the 3/8” nylon locknut (not shown). 19. Route t...

  • Page 12

    12 22. Locate the short cable (58). Route the short cable under the 3 1/2” low pulley (77). Be sure that the end of the cable with the ball is on the indicated side of the pulley and that the cable is between the pulley and the welded spacer on the leg lever (29). Tighten the 3/8” x 3 1/2” bolt (16)...

  • Page 13

    13 26. Note: the 3 1/2” pulley (15) labeled in this step is pre-attached. It is shown removed for easy part identification. Route the short cable (58) around the 3 1/2” pulley (15) attached to the upper hole in the press frame (17). Be sure that the cable is routed around the pulley as shown. Tighte...

  • Page 14

    14 29. Attach the long cable (23) to the small “u”- bracket (67) with a 1/4” nylon locknut (2) and a 1/4” flat washer (10). Do not com- pletely tighten the nylon locknut. It should be threaded onto the end of the cable only a couple of turns, as shown in the inset drawing. Attach the small “u”-brack...

  • Page 15

    15 32. Press a 1 3/4” square inner cap (44) into the press adjustment tube (79). Align one set of holes in the press adjustment tube (79) with the holes in the rocker arm (32). Insert the “l”-pin (40) through the holes. Be sure that the press adjustment tube is oriented as shown. Attach the press pl...

  • Page 16: Adjustment

    16 adjustment the instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym system should be set up for each exercise. Important: when attaching the lat bar or nylon strap, make sure that the attach...

  • Page 17

    17 adjusting and removing the leg press plate and adjustment tube to adjust the position of the leg press plate (78), remove the “l”-pin (40) from the press adjustment tube (79) and the rocker arm (32). Align a different set of holes in the press adjustment tube with the set of holes in the rocker a...

  • Page 18

    18 trouble-shooting and maintenance inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. Tightening the cables woven cable, the type of cabl...

  • Page 19: Cable Diagram

    19 cable diagram the cable diagram below shows the proper routing of the short cable (58) and the long cable (23). Use the diagram to be sure that the two cables and the cable traps have been assembled correctly. If the cables have not been correctly routed, the home gym system will not function pro...

  • Page 20: Ordering Replacement Parts

    Ordering replacement parts to order replacement parts, simply call our customer service department toll-free at 1-800-999-3756, monday through friday, 6 a.M. Until 6 p.M. Mountain time (excluding holidays). To help us assist you, please be pre- pared to give the following information: 1. The model n...

  • Page 21: Chart From The Manual!

    This chart is provided to help you identify the small parts used in assembly. Important: some parts may have been pre-assembled for shipping purposes; if you cannot find a part in the parts bags, check to see if it has been pre-assembled. Remove this part identification chart from the manual! Please...

  • Page 22

    Arruela plana de 1/4” arruela plana de 5/16” (8)–8 arruela plana de 3/8” (9)–5 parafuso de 1/4” x 2 1/2” (43)–2 parafuso de 5/16” x 1 3/4” (72)–1 pino de montagem 5/16” x 2 1/2” (1)–4 pino de montagem de 5/16” x 2 3/4” (14)–2 parafuso de 1/4” x 1/2” (18)–2 parafuso de 5/16” x 2 1/2” (22)–5 pino de 5...

  • Page 23

    Retentor de 1” (69)–4 contrapino de 3/8” (21)–15 porca de nylon de 3/8” (33)–1 pino de 3/8” x 2 (12)–3 pino de 3/8” x 3 1/2” (16)–3 pino de 3/8” x 2 1/2” (7)–5 pino de 3/8” x 3 3/4” (71)–3 clipe do cabo (53)–3 pino de 3/8” x 3 1/4” (35)–1 contraporca de nylon de 1/4” (3)–20 contraporca de nylon de 1...

  • Page 24

    Tampa interna redonda de 1” (49)–4 coberta redonda de 1” (70)–2 tampa interna redonda de 3/4” (34)–4 espaçador de 1/2” x 3/4” (61)–2 tampa interna quadrada de 1 3/4” (44)–10 tampa interna quadrada de 22” (27)–3 tampa externa quadrada de 2” (51)–2 mancal plástico de 1’ x7/8” (75)–2.

  • Page 25: Drawing From The Manual!

    Remove this part list/exploded drawing from the manual! 8 1.

  • Page 26

    Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Part list—model no. Wesy85201 r1096a key no. Qty. Description 1 4 5/16” x 2 1/2” carriage bolt 23 1/4” nylon locknut 3 20 5/16” nylon locknut 4 1 base 5 1 stabilizer 6 4 “v”-pulley 7 5 3/8” x 2 1/2” bolt...

  • Page 27

    7 50 6 21 69 70 69 70 47 48 44 45 44 45 74 74 11 11 8 8 55 27 12 15 44 15 71 23 27 21 44 21 49 3 61 60 56 15 3 21 6 50 7 42 66 68 55 3 21 66 15 20 12 12 2 57 58 21 3 5 19 26 51 25 64 63 76 9 21 10 43 10 62 67 3 72 10 2 41 14 51 1 1 4 15 15 3 3 66 66 49 46 49 46 22 3 9 16 44 44 15 21 59 75 21 13 27 3...