1. DL manuals
  2. Weider
  3. Other
  4. 8525
  5. User Manual

Weider 8525 User Manual - Seat Assembly

Other manuals for 8525: User Manual, User Manual
Manual is about: Weight system

Summary of 8525

  • Page 1

    User's manual questions? As a manufacturer, we are com- mitted to providing complete customer satisfaction. If you have questions, or find there are miss- ing or damaged parts, we will guarantee you complete satisfac- tion through direct assistance from our factory. To avoid unnecessary delays, plea...

  • Page 2: Table Of Contents

    2 table of contents important precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 3: Warning

    3 warning : to reduce the risk of serious injury, read the following important precautions before using the weight system. Important precautions warning: before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with...

  • Page 4: Before You Begin

    4 before you begin assembled dimensions: height: 76 in. Width: 37 in. Length: 48 in. Foot plate low pulley station high pulley station left side right side lat bar decal 1 decal 2 leg lever butterfly arms press arm preacher pad weight stack seat backrest weight pin thank you for selecting the versat...

  • Page 5: Frame Assembly

    5 1 56 high side of bracket 3 5 51 51 14 1 27 4 1. Before beginning assembly, be sure that you have read and understand the information in the box above. Press a 2” square outer cap (51) onto each end of the stabilizer (5). Press a 2” square inner cap (27) into the end of the base (4). Insert two 5/...

  • Page 6

    6 2. Slide the front upright (42) onto the 5/16” x 2 1/2” carriage bolts (1) in the base (4). Hand tighten a 5/16” nylon locknut (3) onto each carriage bolt. Do not tighten the nylon locknuts yet. Press a 1” square inner cap (65) into the front upright (42). 3. Press a 2” square inner cap (27) into ...

  • Page 7: Arm Assembly

    7 5. Press the weight tube bumper (64) into the end of the weight tube (63). Insert the weight tube into the stack of weights (25). Be sure that the pins on the weight tube are resting in the pin grooves in the upper weight. Lubricate the insides of the holes in the top weight (76). Set the top weig...

  • Page 8

    8 8. Press a 1 3/4” square inner cap (44) into the top of a press arm (46). Press a 1” round inner cap (49) into each end of the handle on the press arm. Attach the press arm (46) to one side of the press frame (17) with two 5/16” x 2 1/2” bolts (22) and two 5/16” nylon locknuts (3). Assemble the ot...

  • Page 9: Cable Assembly

    9 11. During steps 11 through 24, refer to the cable diagram on page 20 of this manual to verify proper cable routing. Before beginning this sec- tion, identify the long cable (23) and the short cable (58) by comparing the lengths of the cables. Important: while assembling the cables, do not overtig...

  • Page 10

    10 15. Route the long cable (23) around the “v”-pulley (6) on the right arm (48). Be sure that the cable is in the groove of the “v”-pulley and that the long cable trap (50) is turned to hold the cable in place. Tighten the 3/8” x 2 1/2” bolt (7) and the 3/8” nylon locknut (not shown). 16. Route the...

  • Page 11

    11 19. Locate the short cable (58). Lay the short cable in the bracket on the base (4). Attach the 3 1/2” pulley (15) to the bracket with a 3/8” x 2” bolt (12) and a 3/8” nylon locknut (21). Be sure that the end of the cable with the ball is on the indicated side of the bracket. 20. Route the short ...

  • Page 12

    12 22. Route the short cable (58) around the 3 1/2” pulley (15) attached to the upper hole in the front upright (42). See the inset drawing. Be sure that the cable trap (66) is turned to hold the cable in place and that the cable is routed around the pulley as shown. Tighten the 3/8” nylon locknut (...

  • Page 13: Seat Assembly

    24. Attach the long cable (23) to the small “u”- bracket (67) with a 1/4” nylon locknut (2) and a 1/4” flat washer (10). See the inset drawing. Do not overtighten the nylon locknut; it should be threaded onto the end of the cable only a couple of turns, as shown. Attach the small “u”-bracket (67) to...

  • Page 14

    14 26. Press a 1 1/2” square inner cap (32) into the seat frame (36). Insert the 1/4” x 2” carriage bolt (38) into the center hole in the seat plate (37). Attach the seat plate to the seat (13) with two 1/4” x 3/4” screws (18). Insert the 1/4” x 2” carriage bolt (38) into the indi- cated hole in the...

  • Page 15

    15 29. Press a 3/4” round inner cap (34) into each end of both 12 1/2” pad tubes (28). Insert one 12 1/2” pad tube (28) into the seat frame (36). Slide a 5 1/2” pad (30) onto each end of the pad tube. Insert the other 12 1/2” pad tube (28) into the leg lever (29). Slide a 5 1/2” pad (30) onto each e...

  • Page 16: Adjustments

    16 adjustments the instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise. Impor- tant: when attaching the lat bar or nylon strap, make sure that the attachme...

  • Page 17

    17 attaching the leg lever to the low pulley station to use the leg lever (29), the seat must be attached to the front upright (see attaching and remov- ing the seat, on page 16). Attach the short cable (58) to the indicated 3/8” x 2” eyebolt (35) with a cable clip (53). Attaching the preacher pad t...

  • Page 18: Weight Resistance Chart

    18 weight press arm butterfly arm leg lever high pulley low pulley plates (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) top 20 10 15 14 24 1 45 22 36 28 54 2 70 33 54 44 82 3 99 42 75 60 115 4 128 48 96 72 147 5 153 60 115 90 175 6 184 69 137 103 209 this chart shows the approximate weight resistance at each s...

  • Page 19

    19 trouble-shooting and maintenance inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. Tightening the cables woven cable, the type of cable us...

  • Page 20: Cable Diagram

    20 cable diagram the cable diagram below shows the proper routing of the short cable (58) and the long cable (23). Use the diagram to be sure that the two cables and the cable traps have been assembled correctly. If the cables have not been correctly routed, the weight system will not function prope...

  • Page 21: Notes

    21 notes.

  • Page 22

    22 note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Part list—model no. Wesy19510 r1101a 1 2 5/16” x 2 1/2” carriage bolt 2 3 1/4” nylon locknut 3 16 5/16” nylon locknut 4 1 base 5 1 stabilizer 6 3 “v”-pulley 7 3 3/8” x 2 1/2” bolt 8 4 5/16” flat washe...

  • Page 23

    23 11 11 8 8 55 27 12 15 44 15 71 23 27 21 44 21 3 61 60 3 56 15 12 2 57 58 21 3 5 51 14 19 26 51 25 64 63 76 9 21 3 3 4 1 27 65 15 71 41 10 43 3 21 6 50 7 42 7 50 6 21 69 70 69 70 47 48 44 45 44 45 13 40 38 37 18 32 28 30 34 10 2 24 36 30 34 14 11 3 29 34 30 28 9 73 49 49 46 32 30 34 35 49 49 46 22...

  • Page 24: Ordering Replacement Parts

    Ordering replacement parts to order replacement parts, simply call our customer service department toll-free at 1-800-999-3756, monday through friday, 6 a.M. Until 6 p.M. Mountain time (excluding holidays). To help us assist you, please be pre- pared to give the following information: 1. The model n...

  • Page 25: Chart From The Manual

    This chart is provided to help you identify the small parts used in assembly. Important: some parts may have been pre-assembled for shipping purposes; if you cannot find a part in the parts bags, check to see if it has been pre-assembled. Remove this part identification chart from the manual please ...

  • Page 26

    5/16" nylon locknut (3) 1/4" flat washer (10) 5/16" flat washer (8) 3/8" flat washer (9) 1/4" x 2 1/2" screw (43) 5/16" x 1 3/4" bolt (72) 3/8" nylon locknut (21) 1/4" x 2" screw (24) 3/8" nylon jamnut (73) 5/16" x 2 1/2" bolt (22) 5/16" x 5" bolt (68) 5/16" x 2 3/4" bolt (11) 1/4" nylon locknut (2)...

  • Page 27

    1" retainer (69) 3/8" x 2" bolt (12) 3/8" x 3 1/2" bolt (16) 3/8" x 2 1/2" bolt (7) 3/8" x 3 3/4" bolt (71) 3/8" x 8" bolt (59) cab le clip (53) 5/16" x 6" bolt (60) 1/4" x 3/4" screw (18) 1/4" x 2" carriage bolt (38) 1" x 7/8" plastic bushing (75) 1 1/8" x 2 1/2" plastic bushing (74).

  • Page 28

    1" round inner cap (49) 1" round cover cap (70) 1/2" x 3/4" spacer (61) round inner cap (77) 1 1/2" square inner cap (32) 1 3/4" square inner cap (44) 2" square inner cap (27) 2" square outer cap (51) 3/8" x 2" eyebolt (35) 1" square inner cap (65) 3/4" round inner cap (34).