1. DL manuals
  2. Weider
  3. Other
  4. 8525
  5. User Manual

Weider 8525 User Manual - Arm Assembly

Other manuals for 8525: User Manual, User Manual
Manual is about: Weight system

Summary of 8525

  • Page 1

    User's manual questions? As a manufacturer, we are com- mitted to providing complete customer satisfaction. If you have questions, or find there are missing or damaged parts, we will guarantee you complete sat- isfaction through direct assis- tance from our factory. To avoid delays, please call dire...

  • Page 2: Table of Contents

    2 table of contents important precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 3: Warning

    3 warning : to reduce the risk of serious injury, read the following important precautions before using the weight system. Important precautions 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensu...

  • Page 4: Before You Begin

    4 before you begin assembled dimensions: height: 76 in. Width: 37 in. Length: 44 in. Foot plate low pulley station high pulley station left side right side lat bar decal 1 decal 2 leg lever butterfly arms press arm preacher pad weight stack seat backrest thank you for selecting the versatile weider ...

  • Page 5: Frame Assembly

    5 1 3 4 27 51 51 14 1 5 1. Press two 2” square outer caps (51) onto the ends of the stabilizer (5). Press a 2” square inner cap (27) into the end of the base (4). Insert two 5/16” x 2 3/4” carriage bolts (14) up through the stabilizer (5). Insert two 5/16” x 2 1/2” carriage bolts (1) up through the ...

  • Page 6

    6 2. Press a 1” square inner cap (65) into the front upright (42). Slide the front upright (42) onto the 5/16” x 2 1/2” carriage bolts (1) in the base (4). Hand tighten two 5/16” nylon locknuts (3) onto the carriage bolts. Do not tighten the locknuts yet. 3. Attach the two weight guides (62) inside ...

  • Page 7: Arm Assembly

    7 6. Press two 1” x 7/8” plastic bushing (75) onto the welded spacers on the press frame (17). Slide the press frame into place on the base (4) as shown. Note: this will be a tight fit. The plastic bushings should fit onto each end of the indi- cated tube in the base. Lubricate the 3/8” x 8” bolt (5...

  • Page 8: Cable Assembly

    8 8. Identify the right arm (48) and the left arm (47) by the position of the welded bracket on each arm. Lubricate both axles on the top frame (55). Press a 1 3/4” square inner cap (44) into the lower end of the left arm (47). Wet the end of the arm with soapy water and slide a 10” pad (45) onto it...

  • Page 9

    9 11. Note: the 3 1/2” pulley (15) in this step has been preassembled. It is shown exploded in this drawing for clarity. Route the short cable (58) around the 3 1/2” pulley (15) attached to the press frame (17). Make sure that the cable trap (66) is turned to hold the cable in place and that the cab...

  • Page 10

    10 18 15 16 17 21 50 7 6 23 21 7 48 47 47 50 6 23 21 12 15 20 66 15 66 23 21 12 57 23 42 15. Wrap the long cable (23) around a “v”-pulley (6). Attach the “v”-pulley and a long cable trap (50) to the indicated bracket on the front upright (42) with a 3/8” x 2 1/2” bolt (7) and a 3/8” nylon locknut (2...

  • Page 11: Seat Assembly

    11 19 23 bracket 15 12 21 55 21 41 10 10 43 43 23 3 72 63 10 2 67 42 20 19. Remove the indicated 3 1/2” pulley (15) from the top frame (55). Route the long cable (23) around the 3 1/2” pulley (15) and reattach it to the bracket on the top frame (55) with the 3/8” x 2” bolt (12) and the 3/8” nylon lo...

  • Page 12

    12 22. Press a 1 1/2” square inner cap (32) into the seat frame (36). Insert the 1/4” x 2” carriage bolt (38) into the center hole in the seat plate (37). Attach the seat plate to the seat (13) with two 1/4” x 3/4” screws (18). Insert the 1/4” x 2” carriage bolt (38) into the indi- cated hole in the...

  • Page 13

    26. Attach the preacher pad (56) to the preacher post (77) with two 1/4” x 3/4” screws (18). 26 18 77 56 13 27. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in adjustments, beginning on the following page. Before using the weight system, pul...

  • Page 14: Adjustments

    14 adjustments the instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise. Impor- tant: when attaching the lat bar or nylon strap, make sure that the attachme...

  • Page 15

    15 attaching the leg lever to the low pulley station to use the leg lever (29), the seat must be attached to the front upright (see attaching and remov- ing the seat, on page 14). Attach the short cable (58) to the indicated 3/8” x 2” eyebolt (35) with a cable clip (53). Attaching the preacher pad t...

  • Page 16: Weight Resistance Chart

    16 weight press arm butterfly arm leg lever high pulley low pulley plates (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) top 20 10 15 14 24 1 45 22 36 28 54 2 70 33 54 44 82 3 99 42 75 60 115 4 128 48 96 72 147 5 153 60 115 90 175 6 184 69 137 103 209 this chart shows the approximate weight resistance at each s...

  • Page 17

    17 troubleshooting and maintenance inspect and tighten all parts each time the weight system is used. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. Tightening the cables woven cable, the type of cable use...

  • Page 18: Cable Diagram

    18 cable diagram the cable diagram below shows the proper routing of the long cable (23) and the short cable (58). Use the diagram to make sure that the two cables and the cable traps have been assembled correctly. If the cables have not been correctly routed, the weight system will not function pro...

  • Page 19

    5/16" nylon locknut (3) 1/4" washer (10) 5/16" washer (8) 1" retainer (69) 3/8" washer (9) 1/4" x 2 1/2" screw (43) 5/16" x 1 3/4" bolt (72) 3/8" nylon locknut (21) 1/4" x 2" screw (24) 3/8" nylon jamnut (73) 1/2" x 17/32" spacer (61) 3/8" x 2" bolt (12) 3/8" x 3 1/2" bolt (16) 5/16" x 2 1/2" bolt (...

  • Page 20

    1" round inner cap (49) round inner cap (78) 1" round cover cap (70) 3/8" x 8" bolt (59) 5/16" x 6" bolt (60) 1" x 7/8" plastic bushing (75) 1 1/8" x 2 1/2" plastic bushing (74) 2" square outer cap (51) 2" square inner cap (27) 1 1/2" square inner cap (32) 1 3/4" square inner cap (44) 3/4" round inn...

  • Page 21

    Remove this part identification chart and part list/ exploded drawing. Save this part identification chart and part list/exploded drawing for future reference. Part list—model no. Wesy19512 r0903a 1 2 5/16” x 2 1/2” carriage bolt 2 3 1/4” nylon locknut 3 16 5/16” nylon locknut 4 1 base 5 1 stabilize...

  • Page 22

    27 12 15 44 15 71 23 27 21 44 21 5 51 25 76 4 1 27 15 71 41 6 50 42 21 13 40 28 30 36 14 29 49 49 46 46 16 15 21 59 17 52 44 44 67 66 66 75 3 72 10 2 15 12 58 7 18 77 56 33 39 55 6 69 70 70 47 48 45 45 6 74 74 50 50 69 20 15 66 3 22 9 21 21 49 49 30 30 30 28 11 8 8 7 68 3 21 12 51 64 63 62 23 34 34 ...

  • Page 23: Ordering Replacement Parts

    Ordering replacement parts to order replacement parts, simply call our customer service department toll-free at 1-800-999-3756, monday through friday, 6 a.M. Until 6 p.M. Mountain time (excluding holidays). To help us assist you, please be pre- pared to give the following information: • the model nu...