User's manual questions? As a manufacturer, we are com- mitted to providing complete customer satisfaction. If you have questions, or if there are missing or damaged parts, we will guarantee you complete satisfaction through our customer service department. Please call: 0345-089009 or write: icon fi...
2 important precautions warning: to reduce the risk of serious injury, read the following important precautions before using the home gym system. Warning: before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons wit...
3 before you begin assembled dimensions: height: 74 in. Width: 60 in. Length: 54 in. Foot plate low pulley station high pulley station lat bar leg lever butterfly arms squat arm press arm weight stacks backrest vkrarms weight pin thank you for selecting the versatile weider ® 8530 home gym system. T...
4 assembly 1 74 56 3 3 8 11 51 27 1 4 3 1 51 27 high side 5 1. Before beginning assembly, be sure that you have read and understand the infor- mation in the box above. Press a 2” inner cap (27) into the indicated end of the stabiliser (5). Press 2” outer caps (51) onto the other two locations on the...
4 2 3 5 2. Insert two 5/16” x 2 1/2” carriage bolts (1) up through the base (4). Slide the front upright (42) onto the 5/16” x 2 1/2” carriage bolts (1) in the base (4). Hand-tighten a 5/16” nylon locknut (3) onto each carriage bolt. Do not tighten the nylon locknuts yet. Press a 1” inner cap (6) in...
5 6 6 5. Press a weight tube bumper (64) into the end of a weight tube (63). Insert the weight tube into the front stack of weights (25). Be sure that the pins on the weight tube are sitting in the pin grooves in the top weight. Lubricate the inside of the holes in a top weight (65). Set the top wei...
7. Attach the upper ends of the long weight guides (62) to the top frame (55) with a 5/16” x 6” bolt (60), two 1/2” x 3/4” spacers (61), and a 5/16’ nylon locknut (3). Be sure that the pulley bracket (20) is in front of the right long weight guide (62) as shown. Attach the upper ends of the short we...
8 11. Lubricate both axles on the top frame (55). Slide the right arm (48) onto the right axle. Be careful not to confuse the right arm with the left arm (47); note the position of the “v” pulley (50) to identify the right arm. Be sure that the upper end of the right arm is behind the indicated brac...
9 during steps 13 to 25, refer to the cable dia- gram on page 19 of this manual. Identify the three cables by their lengths, and note the posi- tions of the cable traps. Important: do not over- tighten the bolts and nuts securing the pulleys. The pulleys must turn freely. 13. Locate the medium cable...
10 17. Route the medium cable (58) around the 3 1/2” pulley (15) attached to the bracket on the top frame (55). Tighten the 3/8” x 2” bolt (12) and the 3/8” nylon locknut (21). (note: this pulley is pre-assembled. It has been shown disassem- bled for easy part identification.) be sure that the cable...
11 21. Attach the medium cable (58) to a small “u”- bracket (71) with a 1/4” nylon locknut (2) and a 1/4” flat washer (10). Do not tighten the 1/4” nylon locknut. It should be threaded onto the cable only a couple of turns. Attach the small “u”-bracket (71) to the indi- cated weight tube (63) with a...
12 24. Wrap the long cable (72) around a 3 1/2” pulley (15). Attach the pulley and two pulley covers (96) to the squat arm (84) with the 3/8” x 2 1/4” bolt (94) and a 3/8” nylon jam nut (92). Be sure that the 3/8” nylon jam nut is on the side shown and that the wide tabs of the pulley covers are in ...
13 26. Attach the backrest (41) to the front upright (42) with two 1/4” x 2 1/2” screws (43) and two 1/4” flat washers (10). 27. Press a 1 1/2” inner cap (32) into the seat frame (36). Insert a 1/4” x 2” carriage bolt (38) through the centre hole in the seat plate (37). Attach the seat plate to the ...
14 30. Press two 3/4” round inner caps (34) into each 13 1/2” pad tube (28). Insert the 13 1/2” pad tube (28) into the seat frame (36). Slide a 6” pad (30) onto each end of the pad tube. Insert the other 13 1/2” pad tube (28) into the leg lever (29). Slide a 6” pad (30) onto each end of the pad tube...
15 how to use the home gym system the instructions below describe how each part of the home gym system can be adjusted. Important: when attaching the lat bar or nylon strap, make sure that the attachments are in the correct starting position for the exercise to be performed. If there is any slack in...
16 attaching and removing the seat to attach the seat (13), set the bracket on the seat frame (36) onto the indicated pins on the front upright (42). Attach the seat frame to the front upright with the 5/16” x 2 3/4” carriage bolt (14) and the seat knob (40). For some exercises, the seat (13) must b...
17 weight resistance chart this chart shows the approximate weight resistance at each station. “top” refers to the 6,5 lbs. Top weight. The other numbers refer to the 12,5 lbs. Weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm. Note: the actual resistance at...
Trouble-shooting and maintenance inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. Tightening the cables woven cable, the type of cable u...
19 cable diagram the cable diagram below shows the proper routing of the long cable (72), the medium cable (58), and the short cable (23). Use the diagram to be sure that the three cables and cable traps have been assembled cor- rectly. If the cables have not been correctly routed, the home gym syst...
Ordering replacement parts if you encounter any difficulties or problems with this product, contact the icon fitness lifestyle ltd. Office, or write: icon fitness lifestyle ltd. Greenwich house 223 north street sheepscar leeds ls7 2aa west yorkshire tel: country code: 0345-089009 fax: 0113-2411120 1...
Wesy87300 r0600a please note: the assembly is divided into five stages: 1) frame assembly, 2) press and butterfly arm assembly, 3) cable and pulley assembly, 4) seat and backrest assembly, and 5) vkr assem- bly. The hardware for each stage is packaged separately. Wait until you begin each assem- bly...
5/16" nylon locknut (3) 1/4" flat washer (10) 5/16" flat washer (8) 3/8" flat washer (9) 3/8" nylon jam nut (92) 5/16" x 2 1/2" bolt (22) 1/4" x 2" carriage bolt (38) 5/16" x 3" bolt (75) 5/16" x 2 3/4" bolt (11) 5/16" x 2 1/2" carriage bolt (1) 5/16" x 2 3/4" carriage bolt (14) 3/8" x 2" bolt (12) ...
1" retainer (69) 5/16" x 6" bolt (60) 3/8" x 3 1/2" bolt (16) 1/4" x 3/4" screw (18) 5/16" x 5" bolt (68) 3/8" x 3 3/4" bolt (88) 3/8" x 8" bolt (59) cable clip (53) 1 1/8" x 2 1/2" plastic bushing (89) 1" x 7/8" plastic bushing (90) 3/8" x 5 1/2" bolt (93) 3 1/2" pulley (15) (not shown to scale) "v...
1" round inner cap (49) 1" round cover cap (70) 3/4" round inner cap (34) 1/2" x 3/4" spacer (61) 5/16" x 2" eyebolt (35) 5/8" x 9/16" spacer (7) 1 1/2" inner cap (32) 1 3/4" inner cap (44) 2" inner cap (27) 2" outer cap (51) 1" inner cap (6) 1" x 2" inner cap (87) 1/2" x 17/32" spacer (91) 5/8" x 5...
Remove this part list/exploded drawing from the manual! 8 1.
Part list—model no. Wesy87300 r0600a note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key no. Qty. Description 1 6 5/16” x 2 1/2” carriage bolt 2 4 1/4” nylon locknut 3 27 5/16” nylon locknut 4 1 base 5 1 stabiliser 6 1 1” inner cap 7 1 5/8” x 9/16” sp...
68 3 20 21 15 66 12 27 83 78 80 75 75 10 81 77 32 83 78 79 3 10 43 74 11 11 3 51 1 1 27 19 51 21 5 25 64 26 12 66 15 63 65 24 2 71 72 3 67 15 76 21 56 54 83 83 52 53 39 21 93 92 15 94 84 3 8 8 22 49 82 83 87 85 22 8 8 3 82 83 87 60 27 21 15 55 12 11 8 15 12 44 88 15 58 21 44 21 3 61 62 24 3 58 71 2 ...
