® user’s manual model no. Wesy99300 serial no. The serial number is found in the location shown below. Write the serial number in the space above. Caution read all precautions and instruc- tions in this manual before using this equipment. Save this manu- al for future reference. Serial number decal ...
2 limited warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 important precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ...
3 important precautions warning: to reduce the risk of serious injury, read the following important precau- tions before using the weight system. 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ens...
4 assembled dimensions: height: 198 cm width: 165 cm depth: 86 cm low pulley station foot plate press arm backrest curl pad adjustment knob butterfly arms weight stack leg press lever thank you for selecting the innovative and versatile weider ® pro 9930 weight system. The weider ® pro 9930 offers a...
5 assembly make sure you have the following tools: • two adjustable wrenches • one standard screwdriver • one phillips screwdriver • one rubber mallet • you will also need grease or petroleum jelly, a small amount of soapy water, and clear tape or masking tape. Note: assembly will be more convenient...
6 1. Before beginning, make sure that you have read and understood the information on page 5. Locate and open the parts bag labelled “frame assembly.” press a 2” square inner cap (38) into the butterfly base (61). Press two 2” square inner caps into the press base (60). Insert four 5/16” x 2 1/2” ca...
7 3. Place two weight bumpers (84) over the indicated holes in the butterfly base (61). Slide the weight guides (58) into the indicated holes. Attach the weight guides (58) to the butterfly base (61) with two 3/8” x 2 1/2” bolts (6), four 3/8” flat washers (17), and two 3/8” jam nuts (18). Slide the...
8 7. Turn the seat brace (75) so the nut is on the side shown. Attach the seat brace to the butterfly base (61) with the indicated 5/16” x 2 1/2” carriage bolts (1) and two 5/16” nylon locknuts (2). Do not tighten the nylonlocknuts yet. 6. Attach the butterfly top frame (64) and the press top frame ...
9 11. Press a 1 1/2” square inner cap (79) into the press seat frame (52). Slide the bracket on the lower end of the press seat frame (52) onto the indicated 5/16” x 2 1/2” carriage bolts (1) in the press base (60). Tighten two 5/16” nylon locknuts (2) onto the bolts. Attach the press seat frame (52...
14. Open the parts bag labelled “cable assembly and pulleys.” for cable identification and routing during steps 14–32, refer to the cable diagrams and cable id chart on pages 19 and 20. Insert two 3/8” x 1” bolts (15) into the welded brackets on the left and right butterfly arms (67, 68). Secure eac...
11 15. Wrap the short cable (71) over a “v” pulley (21) as shown. Attach the “v” pulley and a long cable trap (14) to one side of the welded bracket on the butterfly upright (62) with a 3/8” x 2 1/2” bolt (6) and a 3/8” nylon locknut (4). Wrap the short cable (71) over another “v” pulley (21), and a...
12 20. Attach the threaded shaft on the medium cable (72) to the small “u”-bracket (43) with a 1/4” flat washer (11) and a 1/4” nylon locknut (16). Note: see the inset drawing. Do not completely tighten the nylon locknut; it should be threaded only two turns onto the end of the cable. Attach the sma...
13 24. Wrap the long cable (73) around a 3 1/2” pulley (5). Attach the pulley and a cable trap (39) to the indicat- ed bracket on the butterfly base (61) with a 3/8” x 2” bolt (35) and a 3/8” nylon locknut (4). 23. Wrap the long cable (73) around a 3 1/2” pulley (5) in the direction shown. Attach th...
14 26. Wrap the long cable (73) around a 3 1/2” pulley (5) in the direction shown. Attach the pulley and a cable trap (39) to the indicated bracket on the press base (60) with a 3/8” x 2” bolt (35) and a 3/8” nylon locknut (4). Make sure that the cable trap is ori- ented as shown. 27. Wrap the long ...
15 29. Wrap the long cable (73) around a “v” pulley (21) in the direction shown. Attach the “v” pulley and a long cable trap (14) to the small tube on the press seat frame (52) with a 3/8” x 3 1/4” bolt (28), a 3/8” flat washer (17), and a 3/8” nylon locknut (4). Note: the small tube has three adjus...
16 seat assembly 34. Press four 3/4” round inner caps (40) into the ends of the pad tubes (48). Insert the pad tubes (48) into the indicated holes in the leg lever (49) and the press seat frame (52). Slide foam pads (47) onto the ends of both pad tubes. 35. Insert a 1/4” x 2 1/2” carriage bolt (12) ...
17 36. Insert a 1/4” x 1 1/2” carriage bolt (82) into the center hole in a seat plate (42). Attach the seat plate to a seat (51) with two 1/4” x 3/4” screws (13). Insert the 1/4” x 1 1/2” carriage bolt (82) into the indi- cated hole in the seat bar (74) and secure it with a 1/4” flat washer (11) and...
18 39. Apply the weider pro 9930 decal in the location shown. 40. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in adjustment, beginning on page 21 of this manual. Before using the weight system, pull each cable a few times to make sure that ...
19 cable diagrams the cable diagrams below and on the next page show the proper routing of the short cable (71), the medium cable (72), and the long cable (73). The numbers show the correct route for each cable. Make sure that the cables are routed correctly, that the pulleys move smoothly, and that...
20 long cable (73) 1 2 3 4 5 6 7 8 9 13 11 12 10
21 using the curl pad to use the curl pad (69), insert the curl post (70) into the seat brace (75) and secure the curl post at the desired height with the adjustment knob (45). Attaching the lat bar or nylon strap to the high pulley station attach the lat bar (50) to the medium cable (72) with a cab...
22 slack can be removed from the long cable (73) by relo- cating the indicated 3 1/2” pulley (5) on the press seat frame (52). To do this, remove the 3/8” nylon locknut (4), 3/8” flat washer (17), and 3/8” x 2 1/2” bolt (6). Re- attach the pulley at the second or third hole, as needed. Trouble-shoot...
23 high arm butterfly curl/ leg raise weight pulley press (lbs.) low pulley (lbs.) plates (lbs.) (lbs.) (lbs.) top 11 20 15 16 17 1 25 39 31 32 37 2 40 59 48 47 56 3 55 78 64 63 76 4 70 97 80 78 95 5 84 117 97 93 115 6 99 136 113 109 135 7 114 156 130 124 154 8 128 175 146 140 174 the chart below sh...
Part no. 173978 r0501aprinted in canada © 2001 icon health & fitness, inc. Ordering replacement parts to order replacement parts, simply call our customer service department toll-free at 1-888-936-4266, monday through friday, 8 a.M. Until 6:30 p.M. Est (excluding holidays). To help us assist you, pl...
Note: assembly is divided into four stages: 1) frame assembly; 2) arm assembly; 3) cable and pulley assembly; and 4) seat assembly. The hardware for each assembly stage is packaged separately. Wait until you begin each stage to open the parts bag for that stage. Remove this part identification chart...
1/4" flat washer (11) 5/16" flat washer (19) 3/8" flat washer (17) 5/16" x 1 3/4" bolt (9) 3/8" nylon locknut (4) 3/8" jam nut (18) 1/4" nylon locknut (16) #10 x 1” screw (32) 5/16" x 2 1/2" carriage bolt (1) 5/16" x 2 1/2" bolt (3) 5/16" x 2 3/4" bolt (20) 1/4" x 2 1/2" carriage bolt (12) 1/4" x 2 ...
1" retainer (25) 3/8" x 2" bolt (35) 3/8" x 3 1/2" bolt (24) 3/8" x 2 1/2" bolt (6) 3/8" x 3 3/4" bolt (7) 3/8" x 8" bolt (30) cable clip (57) 3/8" x 3 1/4" bolt (28) "v" pulley (21) (not shown to scale) 3 1/2" pulley (5) (not shown to scale) 4 1/2" pulley (34) (not shown to scale) 3/8" x 1" bolt (1...
1" round inner cap (41) 1" round cap (26) 3/4" round inner cap (40) 1 1/2" square inner cap (79) 1" inner cap (80) 1 3/4" square inner cap (37) 2" square inner cap (38) 1" x 7/8" plastic bushing (29).
8 1 remove this part list/exploded drawing from the manual.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Part list—model no. Wesy99300 r0501a key no. Qty. Descriptionkey no. Qty. Description 1 8 5/16” x 2 1/2” carriage bolt 2 27 5/16” nylon locknut 3 4 5/16” x 2 1/2” bolt 4 18 3/8” nylon locknut 5 15 3 1/2”...
65 13 70 37 25 26 66 37 65 67 18 18 71 25 26 37 18 71 68 15 27 18 69 51 82 42 13 45 2 2 2 88 11 16 19 20 74 2 2 38 73 4 1 39 5 35 1 61 39 5 7 4 4 39 5 35 2 2 4 17 39 5 35 62 4 5 5 22 36 2 6 21 14 38 38 41 46 20 64 2 38 39 5 7 20 19 46 63 5 24 72 2 2 17 18 2 17 4 34 22 18 17 6 6 72 2 9 43 11 16 78 77...