1. DL manuals
  2. Weider
  3. Home Gym
  4. VIPER 2000 WESY60400
  5. Replacement Parts Manual

Weider VIPER 2000 WESY60400 Replacement Parts Manual

Summary of VIPER 2000 WESY60400

  • Page 1

    Questions? As a manufacturer, we are com- mitted to providing complete customer satisfaction. If you have questions, or find that there are missing or damaged parts, we will guarantee you complete satisfaction through our customer service department. Please call: 0345-089009 or write: icon fitness l...

  • Page 2

    2 table of contents important precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 3

    3 before you begin assembled dimensions: height: 75 1/2 in. Width: 55 3/4 in. Length: 72 in. Foot plate low pulley station high pulley station lat bar leg lever arms stepper weight stack backrest resistance cylinders vkr arms weight pin 18 thank you for selecting the versatile weider ® viper 2000. T...

  • Page 4

    Assembly 4 1 2 88 4 82 bracket low side 14 88 5 3 8 3 11 86 8 11 3 20 4 1 27 1 17 before beginning assembly, carefully read the following information and instructions: • place all parts of the viper 2000 in a cleared area and remove the packing materials; do not dispose of the packing materials unti...

  • Page 5

    3. Press the 1 1/4” inner cap (57) into the front upright (42). Attach the 1” plastic stop (64) to the centre hole in the stop bracket (63) with a 5/16” x 1 1/2” bolt (24) and 5/16” nylon locknut (3). Attach the stop bracket (63) to the front upright (42) with a 5/16” x 2” bolt (61), 5/16” flat wash...

  • Page 6

    6 15 adjustment the instructions below describe how each part of the weight system can be adjusted. Important: when attaching the lat bar or nylon strap, make sure that the attachments are in the correct starting position for the exercise to be performed. If there is any slack in the cable or chain ...

  • Page 7

    7 14 9 10 11 79 pin groove welded pin 80 72 upper ends of weight guides have holes 25 25 72 67 74 73 3 44 68 67 49 49 42 69 7 18 44 lubricate 52 9. Press the weight tube endcap (79) into the indi- cated end of the weight tube (80). Insert the weight tube (80) into the stack of weights (25). Slide th...

  • Page 8

    8 12. Press two 1 3/4” inner caps (44) into each of the arms (46). Apply lubricant to the lower axles on the arm frame (52). Slide an arm (46) onto one of the axles. Hold two 1” retainers (54) and a 1” round cover cap (55) against the lower end of the axle. The teeth on the retainers must bend towar...

  • Page 9

    9 15. Attach the wide swivel bracket (71) to the indi- cated bracket on the top frame (67) with a 5/16” x 3 1/4” bolt (35) and 5/16” nylon locknut (3). Do not overtighten the nylon locknut; the wide swivel bracket must be able to swivel freely. 16. If the parts shown at the right have not been pre- ...

  • Page 10

    10 19. Remove the 3/8” nylon locknut (21), 3/8” x 1 3/4” bolt (48), and 4 1/2” pulley (77) from one end of the “i” plates (78). Route the long cable (66) under the pulley and reattach the pulley to the “i” plates with the bolt and nylon locknut. Refer to the inset drawing. (note: the wide swivel bra...

  • Page 11

    This chart is provided to help you identify the small parts used in assembly. Important: some parts may have been pre-assembled for shipping purposes; if you cannot find a part in the parts bags, check to see if it has been pre-assembled. Remove this part identification chart from the manual! 1" rou...

  • Page 12

    1/2" x 3/8" spacer (51)—2 5/16" x 2" bolt (61)–3 5/16" nylon locknut (3)–30 1/4" flat washer (10)–10 5/16" flat washer (8)–23 1" retainer (54)–6 3/8" flat washer (9)–5 5/16" jam nut (2)–2 1" plastic stop (64)–1 1/4" nylon locknut (7)—6 1/2" x 1/2" spacer (65)—2 3/8" nylon locknut (21)–12 5/8" retain...

  • Page 13

    Part list—model no. Wesy60400 r0997a note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the user’s manual for information about ordering replacement parts. Remove this part list/exploded drawing from the manual! 81 key no. Qty. Desc...

  • Page 14

    97 95 96 91 55 54 93 93 54 55 89 90 92 43 10 98 11 3 100 101 99 99 47 49 47 10 102 8 3 49 32 8 61 102 10 61 8 49 32 8 3 6 6 49 96 95 3 77 77 78 78 21 82 88 5 4 19 11 8 1 21 20 3 27 15 59 48 34 34 50 32 31 50 34 29 3 33 7 30 10 7 28 34 32 36 39 13 38 37 18 40 14 23 87 8 22 16 15 3 3 8 3 21 9 26 88 42...

  • Page 15

    3 82 88 5 4 19 11 8 1 21 20 3 27 15 59 48 34 34 50 32 29 3 33 7 30 10 7 2 32 36 39 13 38 37 18 40 14 23 87 8 22 16 15 3 3 8 3 21 9 26 88 42 41 10 43 25 79 80 24 81 23 3 85 84 45 44 8 33 49 51 47 8 3 54 55 46 9 70 55 54 3 8 49 45 44 51 9 46 44 53 53 44 44 104 49 52 60 49 21 15 3 21 33 56 48 58 57 8 3...