1. DL manuals
  2. Woods
  3. Cutter
  4. BW126X
  5. Operator's Manual

Woods BW126X Operator's Manual

Manual is about: BATWING ROTARY CUTTER

Summary of BW126X

  • Page 1

    Op e r a t o r 's m a nu a l batwing - rotary cutter man0962 ( r e v. 5 /27/ 201 4) ® bw180x bw180xq bw126x bw126xq.

  • Page 2: 2 Introduction

    2 introduction gen’l (rev. 3/28/2012) to the dealer: assembly and proper installation of this product is the responsibility of the woods ® dealer. Read manual instructions and safety rules. Make sure all items on the dealer’s pre-delivery and delivery check lists in the operator’s manual are complet...

  • Page 3: Introduction 3

    Introduction 3 man0962 (1/9/2012) table of contents introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 general information . . . . . . . ...

  • Page 4: 4 Introduction

    4 introduction man0962 (1/9/2012) specifications bw180x / bw180xq bw126x / bw126xq cutting height (varies with tire selection) . . . . . . . . . . . . . . . . . . . 1" - 15" 1" - 15" cutting width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180" (15’) 126" (10.5’) ...

  • Page 5: Safety 5

    Safety 5 safety video order form (8/2/2005) free mower safety video fill out and return the order form and we will send you a free vhs or dvd video outlining industrial and agricultural mower safety practices. The 22 minute video, developed in cooperation with aem (association of equipment manufactu...

  • Page 6: 6 Safety

    6 safety safety video order form (rev. 2/6/2006) free mower/cutter safety video order form (select one) vhs format - vhs01052 safety video dvd format - dvd01052 safety video please send me name: ________________________________________ phone: __________________ address: _____________________________...

  • Page 7: Safety 7

    Safety 7 bw180_ sr (rev. 12/10/2007) installation  hydraulics must be connected as instructed in this manual. Do not substitute parts, modify, or connect in any other way. Training  safety instructions are important! Read all attachment and power unit manuals; follow all safety rules and safety de...

  • Page 8: 8 Safety

    8 safety bw180_sr (rev. 12/10/2007) (safety rules continued from previous page)  make sure driveline guard tether chains are attached to the tractor and equipment as shown in the pamphlet that accompanies the driveline. Replace if damaged or broken. Check that driveline guards rotate freely on driv...

  • Page 9: Safety 9

    Safety 9 bw180_ sr (rev. 12/10/2007) (safety rules continued from previous page)  full chain or rubber shielding must be installed when operating in populated areas or other areas where thrown objects could injure people or dam- age property. • if this machine is not equipped with full chain or rub...

  • Page 10: 10 Safety

    10 safety bw180_sr (rev. 12/10/2007) (safety rules continued from previous page)  never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body under- neath equipment or between moveable parts even when the engine has bee...

  • Page 11: Safety 11

    Safety 11 man0962 (1/9/2012) 4 - pn 18869 shield missing do not operate - put shield on 18869-b danger be careful! Use a clean, damp cloth to clean safety decals. Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edge...

  • Page 12: 12 Safety

    12 safety man0962 (1/9/2012) 7 - pn 15503 falling off can result in being run over. Tractor must be equipped with rops (or rops cab) and seat belt. Keep foldable rops systems in “locked up” position at all times. Buckle up! Keep seat belt securely fastened. Allow no riders. Raised equipment can drop...

  • Page 13: Safety 13

    Safety 13 man0962 (1/9/2012) safety & instructional decals attention! Become alert! Your safety is involved! Replace immediately if damaged! 12 - pn 1004991 transport lock and cylinder requirements 1004991 transport lock warning raised cutter can drop and crush ers must be equipped with transport lo...

  • Page 14: 14 Operation

    14 operation man0962 (1/9/2012) operation the designed and tested safety of this machine depends on it being operated within the limitations as explained in this manual. Be familiar with and follow all safety rules in the manual, on the cutter and on the tractor. The safe operation of this cutter is...

  • Page 15: Operation 15

    Operation 15 man0962 (1/9/2012) hydraulic connection 1. Inspect hydraulic hoses to ensure they are in good condition. 2. Clean the fittings before connecting them to the tractor hydraulic ports. 3. Route the hose through the hose holder at the hitch and be sure the hose can slide freely in the holde...

  • Page 16: 16 Operation

    16 operation man0962 (1/9/2012) tractor operation use care when operating around tree limbs and other low objects. Avoid being knocked off tractor and being injured. Only use a tractor with a roll over protection structure (rops) and seat belt. Securely fasten seat belt. The cutter is operated with ...

  • Page 17: Operation 17

    Operation 17 man0962 (1/9/2012) transporting  power unit must be equipped with rops or rops cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable rops system in “locked up” position at all times.  always raise ...

  • Page 18: 18 Operation

    18 operation man0962 (1/9/2012) storage follow these steps when storing your cutter: 1. Clean cutter before storing. See page 23 for cleaning instructions. Store on level, solid ground. 2. Disconnect driveline and secure up off the ground. 3. Lower wings to ground. 4. Raise cutter center section and...

  • Page 19: Owner Service 19

    Owner service 19 man0962 (1/9/2012) owner service the information in this section is written for operators who possess basic mechanical skills. If you need help, your dealer has trained service technicians available. For your protection, read and follow the safety informa- tion in this manual.  kee...

  • Page 20: 20 Owner Service

    20 owner service man0962 (1/9/2012) figure 5. Jackstand placement and lubrication points lubrication do not let excess grease collect on or around parts, particularly when operating in sandy areas. See figure 5 for lubrication points and frequency or lubrication based on normal operating conditions....

  • Page 21: Owner Service 21

    Owner service 21 man0962 (1/9/2012) seasonal lubrication in addition to the daily recommended lubrication, a more extensive application is recommended season- ally. 1. Fill cv double yokes with 20 pumps of grease with the joints in a straight line. 2. Articulate cv body to maximum angle several time...

  • Page 22: 22 Owner Service

    22 owner service man0962 (1/9/2012) blade sharpening notice ■ when sharpening blades, grind the same amount on each blade to maintain balance. Replace blades in pairs. Unbalanced blades will cause excessive vibration, which can damage gearbox bearings. Vibration may also cause struc- tural cracks to...

  • Page 23: Owner Service 23

    Owner service 23 man0962 (1/9/2012) shielding repair  full chain or rubber shielding must be installed when operating in populated areas or other areas where thrown objects could injure people or dam- age property. • if this machine is not equipped with full chain or rubber shielding, operation mus...

  • Page 24: 24 Troubleshooting

    24 troubleshooting man0962 (1/9/2012) troubleshooting problem possible cause solution does not cut dull blades sharpen blades. Worn or broken blades replace blades. (replace in pairs only.) incorrect pto speed set at rated pto speed. Ground speed too fast reduce ground speed. Drive not functioning (...

  • Page 25: Dealer Service 25

    Dealer service 25 man0962 (1/9/2012) dealer service the information in this section is written for dealer ser- vice personnel. The repair described here requires special skills and tools. If your shop is not properly equipped or your mechanics are not properly trained in this type of repair, you may...

  • Page 26: 26 Dealer Service

    26 dealer service man0962 (1/9/2012) vertical shaft seal replacement (figure 13) 1. Disconnect and remove the rear driveline from the gearbox. 2. Remove vent plug (24) and siphon gear lube from housing through this opening. 3. Remove crossbar (see page 30). 4. Remove protective seal (8) and vertical...

  • Page 27: Dealer Service 27

    Dealer service 27 man0962 (1/9/2012) correct diameter. Be sure not to damage the seal lip. 8. Press in housing so that seal is recessed. Press protective seal (8) until seated flush with housing. Verify that the seal (8) is seated correctly. 9. Press bearing (7) into the housing, using a round tube ...

  • Page 28: 28 Dealer Service

    28 dealer service man0962 (1/9/2012) splitter gearbox repair (figure 14) removal from cutter 1. Disconnect and remove all drivelines from gearbox. 2. Remove the four cap screw and lock washers that secure gearbox to cutter, and remove gearbox. Note: gearbox is heavy: do not attempt to move it withou...

  • Page 29: Dealer Service 29

    Dealer service 29 man0962 (1/9/2012) check gearbox 1. Place top cover (21) on housing and secure into position using six cap screws (20). 2. Check gearbox for leaks by: plugging all holes except one, applying 4 psi of compressed air, and immersing gearbox in water. Verify gearbox does not leak. Note...

  • Page 30: 30 Dealer Service

    30 dealer service man0962 (1/9/2012) crossbar removal 1. It is necessary to gain access to bottom side of cutter for crossbar removal. See blocking method page 19. Note: you will need to use either the puller screw (item 6, figure 16) or a small hydraulic jack to remove the crossbar. 2. Remove blade...

  • Page 31: Dealer Service 31

    Dealer service 31 man0962 (1/9/2012) crossbar installation 1. Using emery cloth (220 or finer), remove surface rust, loctite ® and foreign material from hub, splined gearbox vertical shaft, and crossbar assembly. 2. Slide crossbar assembly (10) onto splined shaft. Install washer (71) and nut (72) an...

  • Page 32: 32 Dealer Service

    32 dealer service man0962 (1/9/2012) 4. Place universal cross in vise as shown in figure 22 and tap on yoke to remove cup. Repeat step 3 for final removal. Drive remaining cup out with a drift and hammer. Figure 22 u-joint assembly 1. Place seals securely on bearing cups. Insert cup into yoke from o...

  • Page 33: Assembly 33

    Assembly 33 man0962 (1/9/2012) assembly instructions dealer set-up instructions assembly of this cutter is the responsibility of the woods dealer. It should be delivered to the owner completely assembled, lubricated and adjusted for nor- mal cutting conditions. The cutter is shipped partially assemb...

  • Page 34: 34 Assembly

    34 assembly man0962 (1/9/2012) install height adjustment cylinder refer to figure 25. 1. Attach base end of cylinder (45) to the spring arm (43) using clevis pin (54) and two cotter pins (62). 2. Extend cylinder rod and place transport lock bracket (46) over cylinder rod clevis. 3. Position cylinder...

  • Page 35: Assembly 35

    Assembly 35 man0962 (1/9/2012) install wheel and hub 1. Insert wheel hub into outside of wheel yoke arm (1) and align holes. 2. Secure into position using cap screw (83) and flanged lock nut (88). 3. Attach wheel to hub using five lug nuts. Install the chamfered side of the lug nut toward the inside...

  • Page 36: 36 Assembly

    36 assembly man0962 (1/9/2012) install 3-joint drive (540 rpm only) before installing cutter input driveline to gearbox, check the tag wired to the driveline and the tag wired to the input shaft of gearbox. Ensure the tag rpm speeds match the rpm speed decal on front of cutter. After con- firming al...

  • Page 37: Assembly 37

    Assembly 37 man0962 (1/9/2012) install cv drive (optional) before installing cutter input driveline to gearbox, check the tag wired to the driveline and the tag wired to the input shaft of gearbox. Ensure the tag rpm speeds match the rpm speed decal on front of cutter. After con- firming all speeds ...

  • Page 38: 38 Assembly

    38 assembly man0962 (1/9/2012) 2. Slide spacer (53) and lock-up bar (16) over clevis pin (18) on back side of cylinder lug & secure with washer (108) and cotter pins (62). 3. Attach base end of wing cylinder (4) to cylinder links (19 & 20) using clevis pin (54) and cotter pins (62). 4. Remove plug f...

  • Page 39: Assembly 39

    Assembly 39 man0962 (1/9/2012) install wing wheel yoke adjustment link  use a suitable lifting device of sufficient capac- ity. Use adequate personnel to handle heavy com- ponents. 1. With a lifting device raise right wing and lock in the up position using the wing lock-up bar. Leave lifting device...

  • Page 40: 40 Assembly

    40 assembly man0962 (1/9/2012) install chain or belt shielding  full chain shielding must be installed when operating in populated areas or other areas where thrown objects could injure people or damage property. • if this machine is not equipped with full chain shielding, operation must be stopped...

  • Page 41: Assembly 41

    Assembly 41 man0962 (1/9/2012) figure 37. Chain shielding installation - right wing shown 6. Front wing chain plate, inner 7. Front wing chain plate, middle 8. Front wing chain plate, outer 9. Rear wing chain plate 15. 5/16 chain - 4 - link 17. 5/16 chain - 6 - link 19. 1/2 nc x 1-1/2 carriage bolt ...

  • Page 42: 42 Assembly

    42 assembly man0962 (1/9/2012) figure 38. Belt shielding installation - center section figure 39. Belt shielding installation - right wing 1. Front center belt shield plate 2. Front right belt shield plate 3. Front left belt shield plate 7. Bent link, .25 x 1.72 x 13.00 8. Bent link, .25 x 9.25 x 9....

  • Page 43: Assembly 43

    Assembly 43 man0962 (1/9/2012) figure 40. Counterweight installation bw126x and bw126xl counterweight installation ■ the offset model is unstable without adequate counterweight. Use counterweight box loaded with 750 lbs. Of steel.  use a suitable lifting device of sufficient capac- ity. Use adequat...

  • Page 44: 44 Assembly

    44 assembly man0962 (1/9/2012) 2. Place brace (2) inside the front corner of the weight box (1) and secure with two cap screws (10), two flat washers (12), and two lock nuts (14). 3. Align mounting plate (4) with slots of rear of weight box. Secure with two cap screws (10), two flat washers (12), an...

  • Page 45: Dealer Check Lists 45

    Dealer check lists 45 man0962 (1/9/2012) dealer check lists pre-delivery check list (dealer’s responsibility) inspect the equipment thoroughly after assembly to ensure it is set up properly before delivering it to the customer. The following check lists are a reminder of points to inspect. Check off...

  • Page 46: 46 Notes

    46 notes man0962 (1/9/2012) notes.

  • Page 47: Parts 47

    Parts 47 man0962 (1/9/2012) parts index batwing ® rotary cutter bw180x, bw180xq bw126x, bw126xq main frame assembly (front section) ...................................................... 48-49 (rear section) ......................................................... 50-51 wing assembly .................

  • Page 48: 48 Parts

    48 parts man0962 (1/9/2012) main frame assembly (front section) rev. (9/11/2013).

  • Page 49: Parts 49

    Parts 49 man0962 (1/9/2012) main frame assembly (front section) ref part qty description 1 19160kt 1 blade kit, ccw 2 ----- 1 gearbox (see pages 58 - 61) 3 1004933 1 driveline complete, 1340, 1.75-20 6.0 w/ clutch (see page 62) 4 ----- 1 splitter gearbox (see pages 54 - 57) 5 1021103 1 cv drive - 54...

  • Page 50: 50 Parts

    50 parts man0962 (1/9/2012) main frame assembly (rear section).

  • Page 51: Parts 51

    Parts 51 man0962 (1/9/2012) main frame assembly (rear section) ref part qty description 6 1003491 1 attitude rod 15 1003495 2 hinge pin 42 1033491 1 center wheel yoke 43 1027305 1 spring arm 44 19710 1 compression spring 3.25 x .69 x 9.5 45 10475 1 hydraulic cylinder 3-1/2 (see page 72) 46 1004814 1...

  • Page 52: 52 Parts

    52 parts man0962 (1/9/2012) wing assembly.

  • Page 53: Parts 53

    Parts 53 man0962 (1/9/2012) wing assembly ref part qty description 1 19160kt 1 blade kit, ccw (right wing) - or - 1 19161kt 1 blade kit, cw (left wing) 2 ----- 1 gearbox (see page 60) 3 1004934 1 driveline complete 1340, 47.6 x 68.1 (see page 66) 4 1031166 1 hydraulic cylinder 3 x 10 (see page 72) 5...

  • Page 54: 54 Parts

    54 parts man0962 (1/9/2012) style - a splitter gearbox assembly ref part part qty description 540 rpm 1000 rpm 1 1034946 1034947 - complete splitter gearbox 2 1034977 1034977 2 output shaft 1-3/4 - 20 3 1034981 1034981 2 seal, output double lip 4 ------- ------- 2 3/8 plug 5 1034984 1034984 2 snap r...

  • Page 55: Parts 55

    Parts 55 man0962 (1/9/2012) style - a splitter gearbox assembly.

  • Page 56: 56 Parts

    56 parts man0962 (1/9/2012) style - b splitter gearbox assembly.

  • Page 57: Parts 57

    Parts 57 man0962 (1/9/2012) style - b splitter gearbox assembly ref part part qty description 540 rpm 1000 rpm 1 1038897 1038898 - complete splitter gearbox 2 1005308 1005308 2 shaft 1-3/4-20 spline, wing 3 1005304 1005304 2 oil seal 4 ------- ------- 2 3/8 plug (not shown) 5 39251 39251 2 snap ring...

  • Page 58: 58 Parts

    58 parts man0962 (1/9/2012) style - a wing & center gearbox assembly.

  • Page 59: Parts 59

    Parts 59 man0962 (1/9/2012) style - a wing & center gearbox assembly ref qty left wing 540 & 1000 right wing 540 & 1000 center 540 only center 1000 only description a 1 1034900 1034899 1034901 1034902 complete repair gearbox 1 1 1034903 **1034903 1034904 1034905 gear crown 2 1 ns ns ns ns gearbox ho...

  • Page 60: 60 Parts

    60 parts man0962 (1/9/2012) style - b wing & center gearbox assembly.

  • Page 61: Parts 61

    Parts 61 man0962 (1/9/2012) style - b wing & center gearbox assembly ref qty left wing 540 & 1000 right wing 540 & 1000 center 540 only center 1000 only description a 1 58806 1034898 58805 1003684 complete repair gearbox 1 1 57316 **57316 57315 1005317 gear crown 2 1 ns ns ns ns gearbox housing 3 1 ...

  • Page 62: 62 Parts

    62 parts man0962 (1/9/2012) center deck drive assembly ref part qty description a 1004933 1 complete center drive assembly 1 1004961 1 yoke, 1-3/4, 20 spline 2 110 2 cross & bearing kit 3 1004962 1 double yoke 4 1005521 1 grease fitting 5 57416 1 friction clutch 1340 1-3/4, 20 spline 6 57438 1 flang...

  • Page 63: Parts 63

    Parts 63 man0962 (1/9/2012) bw180x & bw126x front drive assembly - equal angle ref part qty description a 57282 1 complete 540 rpm (6-spline) 1 40563 1 yoke 1-3/8, 6-spline (540 rpm) 2 40566 2 cross & bearing 3 40751 2 inboard yoke 4 40753 1 outer profile 5 40765 2 spring pin 10 x 90 6 57299 1 yoke ...

  • Page 64: 64 Parts

    64 parts man0962 (1/9/2012) bw180x & bw126x rear drive assembly - equal angle ref part qty description a 1004932 1 complete rear drive assembly 1 1004957 1 yoke, 1-3/4, 20 spline 2 40566 1 cross and bearing 3 1003471 1 inboard yoke 4 1004958 1 inner profile 5 40765 1 spring pin 10 x 90 6 1029936 1 s...

  • Page 65: Parts 65

    Parts 65 man0962 (1/9/2012) 540 rpm & 1000 rpm front cv drive ref part qty description a 1021103 1 complete cv drive (540 rpm) a 1021104 1 complete cv drive (1000 rpm) 1 19851 1 slide lock repair kit 2 1033103 1 yoke qd cv 1.375 - 6 (540 rpm) 2 1033104 1 yoke qd cv 1.375 - 21 (1000 rpm) 3 1033107 2 ...

  • Page 66: 66 Parts

    66 parts man0962 (1/9/2012) wing drive assembly ref part qty description a 1004934 complete wing drive assembly 1 1004963 1 yoke 1-3/4, 20 spline 2 110 2 cross & bearing kit 3 40764 2 spring pin 10 x 80 4 40575 1 inboard yoke 5 40587 1 inner profile 6 1004964 1 outer profile & sleeve 7 40576 1 inboa...

  • Page 67: Parts 67

    Parts 67 man0962 (1/9/2012) 5-bolt wheel & tire assembly ref part qty description 1 1017050 1 heavy hub assembly (includes items 1 through 15) 2 1017034 1 heavy wheel hub with cups (includes items 6,7,14) 3 1017033 1 axle 4 1017027 1 seal 5 1017028 1 bearing cone 6 1017036 1 bearing cup 7 1017037 1 ...

  • Page 68: 68 Parts

    68 parts man0962 (1/9/2012) bw180x / bw180xq rubber shielding - center section (front & rear) (standard on bw180x models) ref part qty description 1 1017057 1 front center belt shield plate 2 1028588 1 front right belt shield plate 3 1028589 1 front left belt shield plate 7 1028506 2 bent link .25 x...

  • Page 69: Parts 69

    Parts 69 man0962 (1/9/2012) bw180x / bw180xq rubber shielding - wing (front & rear) (standard on bw180x models) ref part qty description 4 1028590 1 front right wing belt shield plate, inside -or- 4 1028591 1 front left wing belt shield plate, inside 5 1027496 1 front right wing belt shield plate, m...

  • Page 70: 70 Parts

    70 parts man0962 (1/9/2012) chain shielding - center section (front & rear) (single row standard on bw126x models) (single row optional on bw180x models) (double row optional on bw126x and bw180x models) single row double row ref part qty description 1 1034850 1 front center chain plate 2 1034855 1 ...

  • Page 71: Parts 71

    Parts 71 man0962 (1/9/2012) chain shielding - wing (front & rear) (single row standard on bw126x models) (single row optional on bw180x models) (double row optional on bw126x and bw180x models single row double row ref part qty description 6 1034857 1 front right wing chain plate, inner -or 6 103485...

  • Page 72: 72 Parts

    72 parts man0962 (1/9/2012) hydraulic cylinders wing 3 x 10 center 3.5 x 8 ref part part qty description 2 19810 23540 1 seal repair kit (includes 2a thru 2g) -or- 2 19810hd -------- 1 seal repair kit w/ heavy duty piston seal(includes 2a thru 2g) 2a ‡ ‡ 1 wiper seal 2c ‡ ‡ 2 1-1/4 id u-cup 2d ‡ ‡ 2...

  • Page 73: Parts 73

    Parts 73 man0962 (1/9/2012) hydraulic cylinder stroke control kit crossbar puller (optional) ref part qty description 1 24098 1 stroke control set for 1-1/4" cylinder rod (contains items 2 - 5) 2 – – – – 2 1-1/2" segment 3 – – – – 1 1-1/4" segment 4 – – – – 1 1" segment 5 – – – – 1 3/4" segment ref ...

  • Page 74: 74 Parts

    74 parts man0962 (1/9/2012) bw126x / bw126xq weight box assembly (optional) ref part qty description 1 1034062 1 weight box 750 lbs 2 1034059 1 brace 3 1010985 1 skid shoe 4 1028566 1 mounting plate 5 1003559 1 1.25 x 1.500 x 3.40 sleeve 6 1003495 1 hinge pin 7 46605 1 clevis pin, 1 x 2.26 ref part ...

  • Page 75: Parts 75

    Parts 75 man0962 (1/9/2012) winch kit (optional) ref part qty description a 1019456 - winch kit, complete 1 52478 4 idler bracket 2 6696 2 chain idler casting 3 409 2 clevis pin, 1/2 x 2 4 22411 2 klik pin, 3/16 x 1 5 3379 * - hhcs, 1/2 nc x 1-1/2 gr5 6 11900 * - lock nut, 1/2 nc flanged 7 1863 * - ...

  • Page 76: 76 Appendix

    76 appendix bolt torque & size charts (rev. 3/28/2007) bolt torque chart always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. ...

  • Page 77: Appendix 77

    Appendix 77 bolt torque & size charts (rev. 3/28/2007) bolt size chart note: chart shows bolt thread sizes and corresponding head (wrench) sizes for standard sae and metric bolts. Abbreviations ag .............................................................. Agriculture asabe.................... Am...

  • Page 78: 78 Index

    78 index man0962 (1/9/2012) index adjustments cutting height 15 slip clutch 22 assembly dealer set-up instructions 33 fill gearboxes 33 dealer check list check lists delivery (dealer’s responsibility) 45 pre-delivery (dealer’s responsibility) 45 dealer service crossbar installation 31 removal 30 gea...

  • Page 79: Warranty

    F-3079 (rev. 5/10/2013) woods equipment a blount international company 2606 south illinois route 2 post office box 1000 oregon, illinois 61061 usa 800-319-6637 tel 800-399-6637 fax woodsequipment.Com warranty all models except mow’n machine tm zero-turn mowers please enter information below and save...

  • Page 80: Warranty

    F-8494 (rev. 2/5/2013) woods equipment a blount international company 2606 south illinois route 2 post office box 1000 oregon, illinois 61061 800-319-6637 tel 800-399-6637 fax woodsequipment.Com ©2013 woods equipment company. All rights reserved. Woods ® and the woods logo are trademarks of woods eq...