Woodway Curve Operating Manual

Other manuals for Curve: Owner's Manual, User Manual
Manual is about: Non-Motorized

Summary of Curve

  • Page 1

    Curve / curve xl motorless treadmill translation of the original german operating manual version: 08/2013-v1.0en.

  • Page 2

    European representative: manufacturer: woodway gmbh steinackerstr. 20 79576 weil am rhein germany woodway usa, inc. W229 n591 foster ct. Waukesha, wi 53186 usa tel.: +49 (0) 7621 - 940 999 - 0 fax.: +49 (0) 7621 - 940 999 - 40 e-mail: info@woodway.De web: www.Woodway.De tel.: +1 262 - 548 - 6235 fax...

  • Page 3

    Contents 08/2013-v1.0de 3 table of contents 1 introduction ............................................................................................. 5 1.1 operating instruction information ................................................. 5 1.2 limitation of liability ..............................

  • Page 4

    Table of contents 4 08/2013-v1.0de 7.5 display ...................................................................................... 31 7.5.1 display parameters .......................................................... 32 7.5.2 display description .....................................................

  • Page 5

    Introduction 08/2013-v1.0de 5 1 introduction 1.1 operating instruction information this manual provides information on the safe operation of the curve treadmill. A condition for safe operation is compliance with all safety and operating instruc- tions. Read and observe the operating instructions! Re...

  • Page 6

    Introduction 6 08/2013-v1.0de 1.3 copyright the release of the operating instructions to third parties without the written permis- sion of woodway is prohibited. Note all contents, text, drawings, images or other illustrations are copyright pro- tected and are subject to intellectual property rights...

  • Page 7

    Introduction 08/2013-v1.0de 7 1.5 customer service for service questions contact the following: woodway gmbh steinackerstr. 20 79576 weil am rhein germany tel. .+49 (0) 7621 - 940 999 - 14 fax. +49 (0) 7621 - 940 999 - 40 email: service@woodway.De for faster processing of your request please have th...

  • Page 8

    Safety 8 08/2013-v1.0de 2 safety 2.1 general the treadmill has been reliably designed, manufactured and tested according to the latest state of technology and is in safe and technically perfect condition. Neverthe- less, the device can cause risk to persons and property if it is operated improperly....

  • Page 9

    Safety 08/2013-v1.0de 9 2.3 safety notices on device there are two safety stickers on the curve. It is noted that the treadmill is motor- less, that the running surface belt only moves in one direction and that the device must be mounted from the rear. Reference is also made to health hazards throug...

  • Page 10

    Safety 10 08/2013-v1.0de 2.5 intended use warning danger from improper use! Any improper use and/or other use of the device can lead to dangerous situa- tions with significant personal injury and/or property damage. ► only use the curve for its intended use. ► read and strictly adhere to all informa...

  • Page 11

    Technical data 08/2013-v1.0de 11 3 technical data 3.1 name plate each woodway treadmill receives a serial number during production. Depending on the year of your model, it has an alphanumeric code with 7-8 characters or a numeric code with 9 digits. The serial number can be found on the nameplate on...

  • Page 12

    Technical data 12 08/2013-v1.0de 3.2 technical specifications device designation: model: curve model: curve xl walking surface (l x w): 172 x 43 cm 218 x 55 cm usable walking surface (l x w): 157 x 43 cm 203 x 55 cm walking surface / technology: walking surface hardness / lateral play: slats (replac...

  • Page 13

    Technical data 08/2013-v1.0de 13 3.3 dimensions fig. 2 device dimensions.

  • Page 14

    Transportation and storage 14 08/2013-v1.0de 4 transportation and storage 4.1 safety notices for transportation check the treadmill for damage upon arrival. Also check and compare supplied ac- cessories with the corresponding delivery note. The manufacturer is not liable for damages and missing part...

  • Page 15

    Product description 08/2013-v1.0de 15 5 product description 5.1 function the curve is a motorless training device. The user controls the desired workout speed with their running speed on the upwardly curved running surface. Fig. 3 curve operation 1. Basic principle of the rotary drive through moving...

  • Page 16

    Product description 16 08/2013-v1.0de 5.2 running surface the walking surface belt consists of individual slats which are mounted on a set of wedged-tooth belts. The individual slats consist of two components: a rubber surface and a t-shaped aluminum base. Due to the approximately 1 cm thick rubber ...

  • Page 17

    Commissioning 08/2013-v1.0de 17 6 commissioning 6.1 general commissioning is the initial intended use of the device, see sec. 0 page 10. Ensure that the conditions applicable to basic safety and health requirements are met. Read these operating instructions completely before commissioning. Before co...

  • Page 18

    Commissioning 18 08/2013-v1.0de 6.3.1 positioning the device fig. 4 installation step, positioning the device • position the unit on a sufficiently solid and horizontal surface. For information see section 6.2 page 17. • there are wheels under the front end of the treadmill. The treadmill can be mov...

  • Page 19

    Commissioning 08/2013-v1.0de 19 6.3.2 mounting the side panels the curve side panels are different from the curve xl side panels. The curve xl panels consist of two separate panels on each side. The panels are separated in the middle (see fig. 8 page 21), further assembly is identical to the curve. ...

  • Page 20

    Commissioning 20 08/2013-v1.0de fig. 6 installation step, fixing bottom of side panel • fix both side panels (on the curve xl four pieces) to the frame. Fix the pan- els to the bottom of the device at the four points in the front and rear with the supplied phillips screws and screwdrivers. • press s...

  • Page 21

    Commissioning 08/2013-v1.0de 21 fig. 8 installation step, fixing top/middle of side panels (curve xl) • the screws should tighten easily and without much resistance. If this is not the case, press slightly on the panel from the outside until the holes in the frame and side panels are aligned and the...

  • Page 22

    Commissioning 22 08/2013-v1.0de fig. 10 installation step, positioning railing • attention! Do not insert the railing completely into the seat. • before inserting the railing into the seat, check that the data wire is protrud- ing out of the base of the device and that the connecting wire is protrud...

  • Page 23

    Commissioning 08/2013-v1.0de 23 • when you have checked the position of the wires, insert the railing into the seat until it stops. If the railing does not slide in easily, adjust the insertion an- gle by slightly moving the railing to the left and right or front and back. Fig. 12 installation step,...

  • Page 24

    Commissioning 24 08/2013-v1.0de fig. 14 installation step, mounting cover plate • then place the cover plates over the bolts on both sides and stow the display wire behind it (on the runner's right). Fig. 15 installation step, fixing cover plates • fix the right and left cover plates with a phillips...

  • Page 25

    Commissioning 08/2013-v1.0de 25 6.3.4 mounting the display open the display box. Unpack the display, two allen screws and the allen key. Fig. 16 mounting the display, connecting the wires connect the two plugs (one from the railing and one from the display) and ensure that a click is heard. Stow the...

  • Page 26

    Operation 26 08/2013-v1.0de 7 operation 7.1 for your safety note consult a doctor! If you are over 40 years old, have a heart condition, are overweight or have not been involved in sports for several years, a visit to the doctor is recom- mended before beginning an intensive training program. For sa...

  • Page 27

    Operation 08/2013-v1.0de 27 7.2 safety equipment 7.2.1 reverse brake the curve non-motorized running face is designed so that the user drives the run- ning surface and controls its speed. This is only possible due to the innovative curved design combined with gravity. For the safety of the user the ...

  • Page 28

    Operation 28 08/2013-v1.0de 7.2.2 safety railing the curve is equipped with a railing that extends along both sides and is bowed around the front. This allows the user to maintain direct contact, so as to obtain safety and stability along the entire curvature of the running surface. For safety reaso...

  • Page 29

    Operation 08/2013-v1.0de 29 7.3.4 calculating maximum heart rate to determine your maximum heart rate subtract your age from the number 220 (general formula). The difference is an approximation of your maximum heart rate. This formula is used by the american heart association (aha) and the american ...

  • Page 30

    Operation 30 08/2013-v1.0de 7.3.6 training frequency at the beginning of training allow yourself enough time to get into shape. After a break from training, you should also allow sufficient time to rebuild physical condi- tion. The priority is regularity and persistence of training - not the intensi...

  • Page 31

    Operation 08/2013-v1.0de 31 7.4.2 transmitter function the signal will only be transmitted if the transmitter is within one meter of the re- ceiver. Note that variations in the heart rate display can occur when the transmitter is too close to other polar ® devices. Maintain at least one meter distan...

  • Page 32

    Operation 32 08/2013-v1.0de 7.5.1 display parameters • manual user speed control (speed) • display for time, calories, distance and pulse • running surface speed indicator (speed) 7.5.2 display description the indicators in the display indicate the following data: displays the current speed in km/h....

  • Page 33

    Operation 08/2013-v1.0de 33 7.6 training process training start attention always use the railing for mounting and dismounting! The curve treadmill may only be mounted in the rear from the side! Never mount from the front! When the treadmill is mounted from the front the running surface starts to mov...

  • Page 34

    Accessories and services 34 08/2013-v1.0de 8 accessories and services for questions about accessories and woodway services call woodway customer service at +49 (0)7621 - 940 999 - 0/ or your responsible woodway dealer. Serves to protect the floor or carpet under the woodway device and at the same ti...

  • Page 35

    Maintenance and cleaning 08/2013-v1.0de 35 9 maintenance and cleaning warning danger of injury due to lack of qualifications! If maintenance or repairs are not carried out by professionally qualified per- sonnel, this may cause material damage and serious injury. ► maintenance and repair work may on...

  • Page 36

    Maintenance and cleaning 36 08/2013-v1.0de 9.2 lubrication 9.2.1 bearings all bearings in the treadmill have been lubricated at the factory and must not be lu- bricated except for the axle bearings. The bearings on the front and rear axle are to be lubricated with a grease gun once a year (two in th...

  • Page 37

    Maintenance and cleaning 08/2013-v1.0de 37 9.3 synchronization belt the synchronization belt on the right side (in running direction) connects the front and rear axles. It ensures equal circumferential axle speed and the exact movement of the running surface belt. The condition of the toothed belt s...

  • Page 38

    Maintenance and cleaning 38 08/2013-v1.0de 9.4.1 weekly maintenance • clean the rails, the front display panel and the cover panels. • check the overall condition of the treadmill. • vacuum under the treadmill. 9.4.2 annual maintenance • vacuum the inside of the treadmill. For this, remove the raili...

  • Page 39

    Disposal notice 08/2013-v1.0de 39 10 disposal notice 10.1 batteries always return used batteries. Discharged batteries can be returned to public collection or retail stores. Batteries supplied by us can be returned to us at no charge. They can also be sent by mail. Returning batteries: this symbol i...

  • Page 40

    Maintenance report 40 08/2013-v1.0de 11 maintenance report d at e m ai n te n an c e m e as u r e s f r o m r e m ar k s.

  • Page 41

    Table of figures 08/2013-v1.0de 41 12 table of figures fig. 1 nameplate ........................................................................................ 11 fig. 2 device dimensions ............................................................................ 13 fig. 3 curve operation ...........