Worksaver JDBS-412 Owner's/operator's Manual
OWNER’S /
OPERATOR’S
MANUAL
MODEL NO.’s
JDBS-412
JDBS-423
JDBS-434
JDBS-433
JDBS-612
JDBS-623
JDBS-634
JDBS-633
SINO LEEINGLES, PIDA AYUDA
A AIGUIEN QUE SI LO LEA
PARA QUE LE TRADUZCA LAS
MEDIDAS DE SEGURIDAD.
MAY 2008
WS-HH029-OG
WORKSAVER, INC.
P.O. BOX 100 LITCHFIELD, IL 62056-0100 (217) 324-5973
WEB: http:// www.worksaver.com E-MAIL: sales@worksaver.com
SAFETY PRECAUTIONS
MOST ACCIDENTS OCCUR BECAUSE OF NEGLECT OR CARELESSNESS.
AVOID NEEDLESS ACCIDENTS BY FOLLOWING ALL OF THE SAFETY PRECAUTIONS LISTED BELOW.
•
Machinery should be operated only by those who are
responsible and are authorized to do so.
•
Stop the engine, lower all equipment, lock the brakes,
and remove the ignition key before dismounting from the
tractor.
•
Never stand between tractor and implement while tractor
is being backed to hitch.
•
Loose fitting clothing should not be worn, to avoid catch-
ing on various parts.
•
Detach implement in area where children normally do not
play.
•
When performing adjustments or maintenance on an
implement, first lower it to the ground or block it securely
at a workable height.
•
Only a qualified operator should be permitted on tractor
when in operation; no riders allowed.
•
Make certain everyone is in the clear before starting
tractor or raising or lowering equipment.
•
Operate the tractor and implement only while seated in
the driver’s seat.
•
Reduce speed when transporting mounted implements
to avoid bouncing and momentary loss of steering
control.
•
A heavy load can cause instability of the tractor. Use
extreme care during road travel. Slow down on turns and
watch out for bumps. Tractor may need front counter-
weights to counter-balance the weight of the implement.
•
Reduce speed on hillsides or curves so there is no
danger of tipping.
•
Avoid driving too close to the edge of ditches or creeks.
•
Do not transport implement on public roads without
reflectors and slow moving vehicle emblem in daylight
and with approved warning lights at night and other
periods of poor visibility.
•
Due to the width of some implements, use extra caution
on highways, farm roads, and when approaching gates.
•
Always be sure the implement is in the proper position for
transport.
•
Keep alert and watch the front as well as the rear when
working with the implement.
OWNER’S /
OPERATOR’S
MANUAL
MODEL NO.’s
JDBS-412
JDBS-423
JDBS-434
JDBS-433
JDBS-612
JDBS-623
JDBS-634
JDBS-633
CAUTION
For Safe Operation
Read Rules And
Instructions Carefully
SINO LEEINGLES, PIDA AYUDA
A AIGUIEN QUE SI LO LEA
PARA QUE LE TRADUZCA LAS
MEDIDAS DE SEGURIDAD.
BALE SPEAR ATTACHMENTS
for John Deere Loaders
Safety Instructions
Maintenance
Assembly & Mounting
Repair Parts
Operating Instructions
CAUTION
THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD
BEFORE ATTEMPTING TO BEGIN ASSEMBLING THIS MACHINE
1. Select an area for assembly that is clean and free of any
debris which might cause persons working on the
assembly to trip.
2. Do not lift heavy parts or assemblies. Use crane, jack,
tackle, fork trucks or other mechanical devices.
3. Preview the assembly instructions in your operator’s
manual before proceeding further.
4. If the assembly instructions call for parts or assemblies to
be blocked up, use only blocking material that is in good
condition and is capable of handling the weight of the
assembly to be blocked. Also insure that the blocking
material is on a clean, dry surface.
5. Never put hands, or any part of body, under blocked up
assemblies if at all possible.
6. After completing assembly, thoroughly inspect the
machine to be sure that all nuts, bolts, hydraulic fittings
or any other fastened assemblies have been thoroughly
tightened.
7. Before operating the machine, thoroughly read the
operation section of your operator’s manual.
8. Before operating, read the maintenance section of your
operator’s manual to be sure that any parts requiring
lubrication, such as gearboxes, are full, to avoid any
possible damage.
9. Before operating equipment – If you have any
questions regarding the proper assembly or
operation, contact your dealer or representative.
MAKE EVERY DAY
A HOLIDAY
FROM ACCIDENTS!
BALE SPEAR
ATTACHMENTS
for John Deere Loaders
WHEN ORDERING REPAIR PARTS,
ALWAYS GIVE THE FOLLOWING INFORMATION:
1. PART NUMBER
2. PART DESCRIPTION
3. MODEL NUMBER
4. NAME OF ITEM
JDBS-412
JDBS-634
JDBS-423
JDBS-612