1. DL manuals
  2. X-PROGRAM
  3. Amplifier
  4. X-D50
  5. Installation Manual

X-PROGRAM X-D50 Installation Manual

Manual is about: Digital 5-channel amplifier

Summary of X-D50

  • Page 1

    Welcome! This owners manual is written in easy english and uses a lot of drawings to simply the installation and use of the above amplifiers. Your x-program amplifiers must be installed correctly in order to work well. This manual will show you how to install the amplifier like a pro. Please read th...

  • Page 2: Installation

    This model include - digital class d technique - high efficiency - low profile design - rca line inputs - parallel input switch - high level input with auto start - phase shift control on mono channel - powerful cable terminals - built-in active crossovers installation before you begin installation ...

  • Page 3

    Tools and material needed tools: flat and phillips screwdrivers wire cutter wire stripper electric drill with drills crimping tool digital multimeter or test lamp wire brush, scraper or a piece of an abrasive sheet to remove paint for a good ground connection grease to protect the ground connection ...

  • Page 4: Wiring

    Wiring power and outputs ground terminal ( gnd ) remote terminal ( rem ) use only 30 ampere atc blade type fuses when replacing a blown fuse. 4 power terminal ( +12v) connect the fuse holder as close to the vehicle battery + as possible, using awg 4 = 21 mm 2 power cable. Use a ring crimp terminal c...

  • Page 5: Input and Controls

    Important use either the low level or high level input, do not use both at same time. Low level input use a pair of shielded stereo audio cables with rca type jack. Most trunk-mount amplifiers need a 20 feet rca cable ( appr 5 – 6 meters). Most under the seat installations require 12 feet ( 2 – 3 me...

  • Page 6: Features / Crossovers

    Input level control the input level control, 6v – 0,3 v, matches the output of your radio to the input of the amplifier. After instal- lation is complete, make sure the in- put of the amplifier is turned down all the way ( counter-clockwise at 6v ). The high pass filter blocks very low frequencies f...

  • Page 7

    X-d50 for power wiring, see page 4 for high or low level input wiring, see page 5 7 filter settings sub channel speaker wiring x-d50 + - filter settings front & rear channels the low pass filter is used for subwoofers. It will allow low frequencies only and blocks higher frequencies. A typical setti...

  • Page 8

    8 2. One or two subwoofers to mono sub channel, each speaker min 4 ohm. Speaker wiring in bridge mode x-d50 front speakers connected in bridge mode filter settings front channels filter settings rear channels the high pass filter blocks very low frequencies from reaching the speakers. It is mostly u...

  • Page 9: Testing

    9 testing before you finish the installation, you should do the following tests to make sure the wiring is correct and everything is operating properly. Reconnect battery when wiring is complete, reconnect the battery negative terminal. If problems occour during the installation, or later, this guid...

  • Page 10

    Noise problems whining noise varying with engine revolutions: do this: 1. Rewire the power supply (12 v) to source unit direct from battery. 2. Rewire ground wire from source unit to clean position on chassis. 3. Check all power connections to ensure that they are clean and tight. 4. Check quality o...

  • Page 11: Specifications

    Specifications we follow a policy of continuous advancement in development. For this reason all or part of specifications & designs may be changed without prior notice. 11 x-program x-d50 number of channels 5 power output, 4 ohm (0,1% thd) 4 x 80 w power output, 2 ohm (0,2% thd) 4 x 130 w power outp...

  • Page 12

    Dls svenska ab p.O. Box 13029 se-40251 göteborg, sweden tel: +46 31 840060 fax: +46 31 844021 e-mail: info@dls.Se www.Dls.Se www.Xprogram.Com.