X10 KR19A Set Up And Operating Instructions - page 2
To test the Motion Detector
Make sure the slide switch on the back of RoboDog is set to RUN (to the left). Arm RoboDog, by pressing the button on the back.
The small red light on the back turns on.
Walk past the Motion Detector. RoboDog starts barking. Five seconds after barking starts RoboDog will turn on Lamp Modules (which are
set to A1). The barking will stop approximately 30 seconds later. If the Motion Detector is tripped again the sequence repeats itself, if no
motion is detected for 4 minutes, RoboDog goes quiet, and the Lamp Module set to A1 will turn off. Note: after the Motion Detector has
been tripped it will not trip again for a period of 30 seconds (for longer battery life). Press the button on the back of RoboDog to disarm it,
the red light goes off.
Note: the KR19A key chain remote normally controls X10 codes A1 and A2.
To change the KR19A's Housecode
• Press and hold the first (top) ON button. The red LED blinks once. 3 seconds later, the LED blinks the current setting: 1 blink for
Housecode A, 2 blinks for B..... 16 blinks for P.
• Release the first (top) ON button.
• Press and release the first (top) ON button the appropriate number of times for the Housecode you want to set. Once for A, twice for B,
etc. The LED blinks for each press. IMPORTANT: Hold the button on your last press. 3 seconds later, the red LED blinks back the new
setting, e.g. 3 blinks for Housecode C. If you do not follow this programming sequence, the LED will stay on for 1 second and your
existing setting will not be changed.
To change the Unit Code for the KR19A's first (top) two buttons (the second pair of buttons are always one # higher than the first pair,
i.e. if you set the first button to 6, the second button controls 7, etc.).
• Press and hold the top OFF button. The red LED blinks once. 3 seconds later, the LED blinks the current setting: 1 blink for Unit Code
1, 2 blinks for 2, 16 blinks for 16.
• Release the top OFF button.
• Press and release the top OFF button the appropriate number of times for the Unit Code you want. IMPORTANT: Hold the button on
your last press. 3 seconds later new code blinks back. If you do not follow this programming sequence, the LED will stay on for 1
second and your existing setting will not be changed.
To change the KR19A's battery: Pry the unit apart and fit a CR2025 Lithium 3V battery. Observe polarity.
You will also need to change the code that RoboDog responds to if you do this see To change RoboDog's default setting of A1.
LIMITED 1-YEAR WARRANTY
X10.com, a division of X10 Wireless Technology, Inc. (X10) warrants X10 products to be free from defective material and
workmanship for a period of one (1) year from the original date of purchase at retail. X10 agrees to repair or replace, at it’s sole
discretion, a defective X10 product if returned to X10 within the warranty period and with proof of purchase.
Please visit www.x10.com/warranty
to complete your on-line warranty registration. Thank you.
F.C.C. CAUTION - THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
This equipment generates and uses radio frequency energy, and if not installed and used properly, that is, in strict accordance with the
manufacturers instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the
limits for remote control security devices in accordance with the specifications in Sub-Part B of Part 15 of FCC Rules, which are designed
to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by
unplugging the equipment, try to correct the interference by one or more of the following measures.
● Reorient the antenna of the radio/TV experiencing the interference.
● Relocate the product with respect to the radio/TV.
● Move the product away from the radio/TV.
● Plug the product into an outlet on a different electrical circuit from the radio/TV experiencing the interference.
If necessary, consult your local dealer for additional suggestions.
NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TO THE UNITS. ANY CHANGES MADE TO THE UNITS WILL
VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
X10.com, a division of X10 Wireless Technology, Inc.
www.x10.com/support
PK9000 inst 10/01 Page 2 of 2