X10 MS15A Set Up And Operating Instructions

The ActiveEYE Motion Sensor sends Wireless Radio Frequency (RF) signals to an X10 Transceiver (RR501 or

TM751). The receiver then passes the signals onto your house wiring to turn on lights, appliances, or X10 wireless

cameras around your home. You plug your lights and appliances into X10 Modules (sold separately). You can set

the ActiveEYE to turn the lights or cameras off after motion stops. You can set this for a preset time of 2, 4, 8

minutes etc. (see below for more details) or you can set any variable delay you like (1 minute min. to 60 minutes

max.) using the NEW easy to set dial on the top of the unit. The ActiveEYE also works with the CM11A Two-

Way Computer Interface to initiate macros (routines) so you can set up a “coming home” routine which is

initiated by the ActiveEYE as soon as it “sees” you.

Note: The default state is to turn lights or cameras on when the ActiveEYE detects motion at all times (even if

it’s not dark). But you can also set it to turn lights or cameras on when it detects motion only at night. It can also

turn lights on at dusk and off at dawn, but this feature is disabled by default (see other side of sheet to enable).

Installation: Remove the screw from the front of the unit (MS16A only). Remove the battery cover and install

two AAA alkaline batteries. Leave the cover off for now. The unit defaults to Housecode A and Unit Code 1,

and it defaults to see motion at all times - day and night, so plug in an X10 RF Transceiver (model RR501 or

TM751, each sold separately) and set it to Housecode A. Plug a lamp into an X10 Lamp Module (sold separately)

and set it to Housecode A and Unit Code 1. Plug the module into any AC outlet.

To test the ActiveEYE: Press the House  button once. The ActiveEYE transmits the “device ON” RF signal

and the red light flashes. Press the Unit button once. The ActiveEYE transmits the “device OFF” RF signal and

the red light flashes. (The default device setting is A1). Replace the battery cover.

Place the ActiveEYE on a shelf or mount it on a wall at least 6 feet above the ground. Let it settle for a minute

and then walk past it. The lamp connected to any X10 Module set to A1 turns on. The light turns off a short time

later as long as no motion has been detected. The default time is the setting on the dial on the top of the unit so

you can adjust this to suit your preference (1 minute min. to 60 minutes max.). You will also see later that you can

set this for a specific predetermined time. For outdoor use, (MS16A only) remove the batteries, screw the

MS16A to a wall and replace the batteries. Refit the cover and screw.

To change the delay after motion is detected before an OFF code is transmitted:

Press the House/On button once. The red light flashes. Then, (within 3 seconds) press and hold the Unit/Off

button. The green light turns on. 3 seconds later the red light reports its delay setting as follows:

1 blink for Analog setting, i.e. the setting on the dial on the top of the unit. 2 blinks for 2 minutes. 3 blinks for 4

minutes. 4 blinks for 8 minutes. 5 blinks for 16 minutes. 6 blinks for 32 minutes. 7 blinks for 64 minutes. 8 blinks

for 128 minutes. 9 blinks for 256 minutes.

To change this, Press the House/On button once. The red light flashes. Then, (within 3 seconds) press and hold

the Unit/Off button. The green light turns on. 3 seconds later the red light reports its delay setting, as listed above.

Release and immediately press the Unit/Off button the number of times for the delay you want, as listed above.

Hold the button pressed for 3 seconds on the last press. The red light then reports the setting with the

appropriate number of blinks as above. Release the button. Note: for settings of 2 blinks or higher, the dial on the

top of the unit is disabled.

To change the Unit Code that the ActiveEYE transmits: Press and hold the Unit/Off button (under the

battery compartment lid) the red light flashes first and then blinks the current setting. Release and immediately

press the button the desired number of times for the Unit Code you want to set. Hold the button for 3 seconds

on the last press. The red light blinks back the number of times for the code you set. Release the button.

To change the House Code that the ActiveEYE transmits: Press and hold the  House/On button (under the

battery compartment lid) the red light flashes first and then blinks the current setting (once for A, twice for B,

etc.). Release and immediately press the button the desired number of times for the House Code you want to set

(once for A, twice for B, etc.). Hold the button for 3 seconds on the last press. The red light blinks back the

number of times for the code you set. Release the button.

Set-Up and Operating Instructions for ActiveEYE Motion Sensors

Models MS15A (Indoor) and MS16A (Indoor/Outdoor)

MS15A/MS16A-4/02. 1 of 2