Summary of SuperRemote UR47A
Page 1
O wner ’ s m anual ur47a x10 dvd s uper r emote.
Page 2
3 2 fcc c aution this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This eq...
Page 3
5 4 i ntroduction congratulations on your purchase of the x10 dvd superremote. Make your lights and appliances go to work for you.... The x10 dvd superremote controls most or all of your video and audio equipment. But what really sets it apart from other remotes is that you can also control almost a...
Page 4
7 6 h ouse c odes and u nit c odes each module has a specific address made up of a house code (red dial on the face of the module) and a unit code (black dial on the face of the module). The controller first sends an address and then a command on the ac power lines. Only the module with a matching a...
Page 5
9 8 1. Set the house code to ‘a’ and the unit code to ‘2.’ 2. Plug a lamp into the lamp module. 3. Plug the lamp module into a convenient ac outlet. X10 dvd s uper r emote the x10 dvd superremote allows you to control practically everything electrical in your home. It has ir technology that lets you...
Page 6
11 10 set up used for programming the remote. 0-9 used as your original remote and to enter device codes. A-b dvd setup. Ent enter same as original remote. Channel, volume, mute works like your original remote. X10 on/off keys lets you control x10 modules to operate lamps and appliances around the h...
Page 7
13 12 6. Point the remote at your a/v component and press the power button. Your a/v component should turn off. U sing aux to control a s econd tv, vcr, c able b ox , s atellite r eceiver , or dvd the aux button is normally used to control an audio component, but it can also be configured to control...
Page 8
15 14 *note: you might have to press channel + many times (50+). If the device does not have a channel up function, use the play button (vcr and dvd only) or the power button. * when searching for, or identifying codes stored under aux, press aux before pressing the mode key. 1. Press and hold the s...
Page 9: X10 M
17 16 you can change 1-4/5-8 slide switch to allow you to control x10 modules set to 9-12/13-16: c hanging the x10 s lide switch setting : 1. Press and hold setup until the led indicator lights steadily. Release setup button. 2. Press and hold all off (led blinks off) for about 8 seconds until the l...
Page 10
19 18 c hanging the x10 h ouse c ode : the superremote defaults to house code a, and in most cases you will not need to change this unless you are experiencing interference from a neighboring x10 system. 1. Press and hold setup until the led indicator lights steadily. Release setup button. 2. Use th...
Page 11
21 20 a i e m o c g k • • • • • • • • 1 9 5 13 15 3 7 11 • • • • • • • unit remote chime house on off rf wall switch bright dim on on 2 1 1 9 5 13 a i e m a b 1 2 3 input mode powerflash interface test all units off 1 9 5 13 a i e m continuous momentary universal module on off sounder & relay relay ...
Page 12
23 22 w arranty 12 month limited warranty x10 (usa) inc. (x10) warrants its products to be free from defective material and workmanship for a period of one (1) year from the original date of purchase at retail. X10 agrees to repair or replace, at its sole discretion, a defective x10 product if retur...
Page 13
X10 (usa) inc. X10 (usa) inc. X10 (usa) inc. X10 (usa) inc. X10 (usa) inc. 91 ruckman rd. 91 ruckman rd. 91 ruckman rd. 91 ruckman rd. 91 ruckman rd. Closter closter closter closter closter, nj 07624 , nj 07624 , nj 07624 , nj 07624 , nj 07624 w w w w web site: www eb site: www eb site: www eb site:...