1. DL manuals
  2. Xantech
  3. Controller
  4. 590-10
  5. Installation Instructions Manual

Xantech 590-10 Installation Instructions Manual

Manual is about: PROGRAMMABLE CONTROLLER

Summary of 590-10

  • Page 1

    Installation instructions 590-10 programmable controller table of contents section title page introduction ................................................................................................................................................. 3 computer requirements...........................

  • Page 2

    Page 2 model 590-10 © 2002 xantech corporation 12v dc ir output reset pc com port serial port 1 (db9, male) pcir-1 (rear panel) computer (typical rear panel of a laptop computer) xantech com port 291-10 ir receiver (optional - see text) to 120 v ac (unswitched) 781rg power supply (included) satellit...

  • Page 3

    Model 590-10 page 3 © 2002 xantech corporation introduction the 590-10 gives the custom installer the ability to use any push button or contact closure to initiate ir commands. The 590-10 incorporates 16 isolated input circuits and a learning microprocessor. There are 16 pair of screw terminals on i...

  • Page 4

    Page 4 model 590-10 © 2002 xantech corporation changing the configuration of these switches requires taking the unit apart and manually moving the jumpers to the desired position. Figure 3 shows the jumpers in their default position. With the jumpers in the default position and switches configured a...

  • Page 5

    Model 590-10 page 5 © 2002 xantech corporation will provide a momentary input and will output the ir command or sequence associated with this switch once per switch closure. Note: these jumpers are in staggered order as shown in the detail in figure 6. Be sure to move the jumper for the appropriate ...

  • Page 6

    Page 6 model 590-10 © 2002 xantech corporation off on gnd +12v in + in – gnd +12v 599-00 pulsed switching module sylmar, ca • made in u.S.A. ® 120 v ac from a switched source + +12v dc 786-00 power supply (most 5 to 12 v dc unregulated power supplies will work) white striped side emitter, connecting...

  • Page 7

    Model 590-10 page 7 © 2002 xantech corporation door chime activated system the circuit below, figure 9, shows a simple means of using a door chime or door bell to activate one of the inputs on a xantech model 590 programmable controller, to initiate a system function or functions. Functions that may...

  • Page 8

    Page 8 model 590-10 © 2002 xantech corporation software installation the installation software for the dragon drop-ir system is included in the supplied cd rom. Install the dragon drop-ir™ software onto your hard drive as follows: windows 95/98/nt/2000/me/xp 1. Insert the drag460 beta cd into your c...

  • Page 9

    Model 590-10 page 9 © 2002 xantech corporation figure 10 - brands figure 11 - components figure 12 - palette editor 1. From the “component” menu, click “pallette editor”. 2. Locate and select (single click) the desired brand as shown in figure 10 (i.E. Sony, panasonic etc). A list of components will...

  • Page 10

    Page 10 model 590-10 © 2002 xantech corporation editing and testing ir commands if a brand, component or function is not found in palette editor, each can be added as follows: adding brands 1. If the brand you need is not already on the list, choose the component menu and click on “add brand”. 2. Ty...

  • Page 11

    Model 590-10 page 11 © 2002 xantech corporation 14. On pop-up (ccf importer), type in brand name and component name (e.G., rca and dss). 15. Double click on desired component type on list of converted files on left side of pop-up (e.G., dss.Cnv). An asterisk (*) will appear just to the left. Click i...

  • Page 12

    Page 12 model 590-10 © 2002 xantech corporation figure 14 – 590-10 base options window selecting palettes a) from the “palette” menu, click “select ir command palette”. (f4) a list of palettes file names appears to the right with select palette in the title bar. B) scroll the list (if necessary) and...

  • Page 13

    Model 590-10 page 13 © 2002 xantech corporation programming sequences all switches on the 590-10 can be programmed to send a single ir command or ir sequences of up to 40 commands. 1. Click the switch to be programmed. 2. Open all palettes to be used in the sequence. 3. In the palettes, click on the...

  • Page 14

    Page 14 model 590-10 © 2002 xantech corporation saving and backing-up files automatic save when working on a project in dragon, it is automatically saved on a continuous basis, it is ok to quit a project at any time and come back to it for further work by simply clicking on open project (ctrl+o) fro...

  • Page 15

    Model 590-10 page 15 © 2002 xantech corporation.

  • Page 16

    Xantech corporation 12950 bradley avenue, sylmar ca 91342-3829 phone 818.362.0353 • fax 818.362.9506 www.Xantech.Com part no. 08901650 rev a 03-13-2002.