- DL manuals
- Xantrex
- Battery Charger
- TC20+
- Owner's Manual
Xantrex TC20+ Owner's Manual - Truecharge+
Introduction
1–2
Truecharge+
Features
Truecharge+ is an advanced battery charger designed specifically for high
performance, deep-cycle lead-acid batteries. It is smaller and lighter than
many other chargers and can be installed or stored in small compartments.
It has AC to DC isolation, a surge protector, and many other safety
features which reduce potential shock and fire hazards.
20/40 Amp Continuous Rating
Truecharge 20+ delivers a 20 amp charging current and the
Truecharge 40+ delivers 40 amps for approximately 75% of the charging
cycle. The chargers only reduce the charging current below these rated
levels when the battery is approaching full charge or when there may be
overheating in high ambient temperatures. Because it delivers rated
current over most of the charge cycle, Truecharge+ charges your batteries
faster than many other chargers with a higher rating.
Many other chargers only deliver their rated charging current for a short
initial part of the charge cycle.
Simultaneous Three-Battery Bank Charging
Truecharge+ has three separate DC positive terminals to allow charging
of three separate batteries (or battery banks). The total current into the
batteries is a maximum of either 20 amperes or 40 amperes, depending on
the model, which is divided amongst the batteries according to their state
of discharge.
Wide Voltage Range Operation
Truecharge+ maintains the correct charging voltage for your battery when
the AC line voltage drops as low as 90 VAC, or rises as high as 135 VAC.
A surge protector in Truecharge+ protects it from surges and spikes on the
AC power line.
Note: The three outputs are not independently voltage regulated so it
is important to avoid systems with mixed types of batteries.
Summary of TC20+
Page 1
Xantrex truecharge 20+/40+ amp multistage battery charger owner’s guide tc20+ tc40+.
Page 2: Owner’S Guide
Owner’s guide truecharge 20+/40+ amp multistage battery charger.
Page 3
About xantrex xantrex technology inc. Is a world-leading supplier of advanced power electronics and controls with products from 50 watt mobile units to 1 mw utility-scale systems for wind, solar, batteries, fuel cells, microturbines, and backup power applications in both grid-connected and standalon...
Page 4: About This Guide
About this guide purpose and scope this guide introduces the truecharge+ battery chargers, describes their features, explains how they charge batteries, and provides procedures for their installation and operation. The guide does not provide details for particular brands of batteries. Please consult...
Page 5
About this guide iv chapter 3, “operation” provides background information for charging batteries with truecharge+ and procedures for charging and for equalizing batteries. Chapter 3 also explains how to calculate charging times, how generators affect truecharge+ and explains how the front panel ind...
Page 6: Contents
V important safety instructions explosive gas precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–x precautions when working with batteries - - - - - - - - - - - - - - - - - - - - - - - - - 1–x 1 introduction truecharge+ features - - - - - - - - - - - - - - - - - ...
Page 7
Contents vi connecting to ac wiring - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–11 grounding - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–14 installing optional accessories - - - - - - - - - - - - - - - - - - - - - - - - - - ...
Page 8
Contents vii maintenance guidelines - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - c–2 preparation for cleaning batteries - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - c–3 clothing- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
Page 9
Viii.
Page 10
Ix important safety instructions 1. Before using the charger, read all instructions and cautionary markings on the charger, the batteries, and all appropriate sections of this guide. 2. Do not expose the charger to rain, snow, spray, or bilge water. To reduce risk of fire hazard, do not cover or obs...
Page 11: Explosive Gas Precautions
Important safety information x 7. Do not disassemble the charger. See appendix d, “product and system information” for instructions on obtaining service. Attempting to service the unit yourself may result in a risk of electrical shock or fire. Internal capacitors remain charged after all power is di...
Page 12
Important safety information xi 3. Wear complete eye protection and clothing protection. Avoid touching your eyes while working near batteries. 4. If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters your eye, immediately flood it with running cold water fo...
Page 14: Introduction
1 introduction chapter 1, “introduction” introduces and describes features of the truecharge+ multistage battery chargers..
Page 15: Truecharge+
Introduction 1–2 truecharge+ features truecharge+ is an advanced battery charger designed specifically for high performance, deep-cycle lead-acid batteries. It is smaller and lighter than many other chargers and can be installed or stored in small compartments. It has ac to dc isolation, a surge pro...
Page 16
Truecharge+ features 1–3 selector switches truecharge+ has selector switches for charge mode, battery type, and battery temperature setting. Charge mode the charge-mode switch allows you to select three-step charge, two-step charge or 13.5 volt fixed output modes. Refer to appendix b, “battery charg...
Page 17
Introduction 1–4 fixed voltage mode the fixed voltage mode setting is meant to be used as a power supply or battery eliminator. It is not meant for charging batteries. The battery type, battery temperature, and equalize switches are all ignored in fixed voltage mode. The remote battery temperature s...
Page 18
Indicator lights and settings on the front panel 1–5 the indicator lights are also used to indicate error codes. See chapter 4, “maintenance and troubleshooting” table 1-1 truecharge+ front panel panel item description 1 status indicator lights which indicate that batteries are charged and ready for...
Page 19: How Truecharge+ Works
Introduction 1–6 how truecharge+ works truecharge+ changes the alternating current (ac) supply from the utility to the controlled low-voltage, direct current (dc) required to charge the battery by using high-frequency, switched-mode power conversion circuits. The high-frequency power conversion meth...
Page 20: Installing
2 installing truecharge+ chapter 2, “installing truecharge+” lists the materials you receive, provides site recommendations for installing truecharge+, and provides the materials and procedures for its installation. The chapter also makes reference to the installation codes that may be applicable in...
Page 21: Materials List
Installing truecharge+ 2–2 materials list contents the unit is packed with the following materials: • owner’s guide • wiring cover with 2 blunt-tip screws and two lock washers • ac cable clamp • three twist-on wire nuts • three crimp-on butt-splices recording information after unpacking the unit, re...
Page 22
Preparing for installation 2–3 location install truecharge+ in a location that meets the requirements set out in table 2-1 . Circuits truecharge+ is designed to operate from a 15 amp, 120 vac (nominal) branch circuit. The circuit must be protected by a 15 amp circuit breaker. Any switch in the circu...
Page 23
Installing truecharge+ 2–4 figure 2-2 truecharge+ system 1 3 .8 / 1 3 . 4 c o ld w a r m h o t 1 4 . 4 / 1 3 . 5 1 4 .0 / 1 3 . 1 1 4 . 2 / 1 3 . 8 o u tp u t v o lt s a b s o r p t io n / f lo a t b a t te r y t y p e f lo o d e d g e l e q u a l iz e c h a r g in g r e a d y b u l k /a b s o r p t...
Page 24
Preparing for installation 2–5 wiring requirements figure 2-2 depicts a typical configuration system for the truecharge+ showing the ac and dc wiring and protection devices required for a successful installation. Dc wiring the dc wiring must meet the following requirements: • length and size use the...
Page 25
Installing truecharge+ 2–6 ac wiring be sure that your ac wiring meets the following requirements before you install the truecharge+: • input wiring the ac input wiring for truecharge+ should be three-conductor cable, providing a line, neutral, and ground conductor in an outer jacket. The conductors...
Page 26
Preparing for installation 2–7 tools to mount and connect truecharge+ you need: p a slot screwdriver with a maximum 3/16 in wide blade for the dc terminals p a no. 1 phillips screwdriver for securing the ac wiring compartment cover p a wire stripper p the manufacturer's recommended crimp tool for an...
Page 27: Installing Truecharge+
Installing truecharge+ 2–8 installing truecharge+ installation steps truecharge+ is installed in three steps. The unit is 1. Mounted ( page 2–8 ) 2. Connected to the batteries ( page 2–9 ) 3. Connected to its ac power source ( page 2–11 ) mounting mount the truecharge+ on a vertical surface such as ...
Page 28
Installing truecharge+ 2–9 connecting dc wiring for a single battery or multiple batteries the procedure for installing the dc wiring applies to a single battery or multiple batteries or battery banks. Figure 2-3 shows the connection order. Figure 2-3 dc wiring connection order warning truecharge+ c...
Page 29
Installing truecharge+ 2–10 to install the dc wiring: 1. Plan the route the dc wires will follow trying to make it as short as possible. Measure the required wire length, and cut the cables. Allow some extra length for connections and to provide slack in the wires. It is possible that the connection...
Page 30
Installing truecharge+ 2–11 8. Before proceeding, carefully check the wiring polarity – make sure the positive on the charger is going to the positive on the batteries (fuse or breaker) and make sure the negative on the charger is going to the battery negative terminal (or engine negative bus or dc ...
Page 31
Installing truecharge+ 2–12 3. Route the wiring without connecting it to the ac source or to the charger yet. 4. Install the supplied cable clamp in the knock-out of your choice on the ac wiring compartment on the top end of the charger and tighten the locknut. Run the ac wiring through the cable cl...
Page 32
Installing truecharge+ 2–13 to connect ac wires with the crimp-on butt-splice connector: 1. Using a wire stripper, carefully strip 5/16” (8mm) from the ends of the two wires being connected. 2. Insert one wire into one end of the butt-splice, insert the butt-splice into the crimping tool, and crimp ...
Page 33
Installing truecharge+ 2–14 grounding truecharge+ must be grounded to reduce the risk of electrical shock. The ac input ground wire must be properly connected to ground in accordance with all applicable electrical codes. Meeting electrical codes is achieved by connecting the ground conductor of the ...
Page 34
Installing optional accessories 2–15 effect on charging with the bts, the charging setpoints are temperature-compensated up to 140 °f (60 °c). If the battery temperature exceeds 140 °f the charger stops charging. The bts also provides more accurate compensation over a wider range of temperatures tha...
Page 36: Operation
3 operation chapter 3, “operation” provides background information for charging batteries with truecharge+ and procedures for charging and for equalizing batteries. Chapter 3 also explains how to calculate charging times, how generators affect truecharge+ and explains how the front panel indicator l...
Page 37: About Charging
Operation 3–2 about charging this section provides information about • calculating the charging time • effect of battery temperature on charging • indicator light activity during the charging process • using a generator to run truecharge+ charging time formula charging time will depend on the capaci...
Page 38
About charging 3–3 battery temperature temperature switch selecting the correct temperature setting selects the appropriate charging voltage to compensate for battery temperature. Effect of temperature cold battery temperature if you choose the cold setting, truecharge + delivers, for example, 14.8 ...
Page 39
Operation 3–4 using a generator as source power the truecharge+ can be run from a regular power source or from an alternate power source such as a generator. Refer to appendix a, “specifications” for ac input draw to determine the size of generator you need. Many generators provide output voltage th...
Page 40: Charging Batteries
Charging batteries 3–5 charging batteries before you start before you start to charge batteries read the “important safety instructions” on page ix and take all safety precautions when working with batteries. To charge your batteries: 1. If possible, disconnect all loads from the battery, by removin...
Page 41
Operation 3–6 2. Set the battery type selector switch according to the table below. 3. Set the battery temperature selector switch for the temperature of your battery as follows: if temperatures fluctuate near the batteries, set this switch each time you charge the batteries. If your batteries are i...
Page 42: Equalizing Flooded Batteries
Equalizing flooded batteries 3–7 light on truecharge40+) will light for most of the charging cycle. Near the end of the cycle, the charging current decreases and the other indicator lights illuminate in sequence. The charger pauses every 15 minutes for approximately 10 seconds to measure the battery...
Page 43
Operation 3–8 battery type truecharge+ equalizes only flooded lead-acid batteries. It does not equalize sealed lead-acid batteries since they can be damaged by this process. If the battery type selector is set for gel or agm, and you try to equalize them, the indicator lights on the front panel flas...
Page 44
Equalizing flooded batteries 3–9 important turn off or disconnect all loads on the battery during equalization. The voltage applied to the battery during equalization may be above the safe levels for some loads. Be sure to check battery electrolyte before and after equalization. Fill only with disti...
Page 45
3–10
Page 46: Maintenance and
4 maintenance and troubleshooting chapter 4, “maintenance and troubleshooting” provides information for maintaining and troubleshooting truecharge+..
Page 47: Care and Maintenance
Maintenance and troubleshooting 4–2 care and maintenance cleaning truecharge+ contains solid-state electronic components that require no maintenance. The best care you can give the unit is to protect it from contact with liquids, spray, or fumes which may cause corrosion. Disconnect all ac and dc po...
Page 48
Troubleshooting 4–3 middle charging current indicator light blinks, all others are off truecharge+ is in over-temperature shutdown due to excessive battery temperature. This shutdown only occurs if the bts is installed. Table 4-1 indicator light sequences on truecharge+ display condition.
Page 49
Maintenance and troubleshooting 4–4 typical problems this section lists typical problems you may have with the truecharge+, suggests their causes, then offers possible solutions to the problems. Symptom indicator lights do not turn on, or remain on, when charger is connected to an ac receptacle. Sym...
Page 50
Troubleshooting 4–5 symptom charging light blinks but does not come on steadily. Other indicator lights are off. Symptom the 20 amp indicator light blinks on truecharge 20+, or the 40 amp light blinks on truecharge 40+. Other indicator lights are off (only when temperature sensor is installed). Symp...
Page 52: Specifications
A specifications appendix a “specifications” contains the truecharge+ physical, electrical, ac input, and protection feature specifications..
Page 53: Physical Specifications
Specifications a–2 physical specifications electrical specifications dimensions 15 1/8 in x 6 3/4 in x 2 3/4 in 385 mm x 172 mm x 70 mm weight truecharge 20+ 6.9 lbs (3.1 kg) truecharge 40+ 7.4 lbs (3.3 kg) ac input connections three color-coded no. 16 awg wires (l, n, g) minimum 6 inches long in a ...
Page 54
Electrical specifications a–3 absorption voltage hot warm cold flooded 14.0 14.4 14.8 vdc gel 13.8 14.2 14.6 vdc agm 14.0 14.3 14.6 vdc float voltage at no load hot warm cold f looded 13.1 13.5 13.9 vdc gel 13.4 13.8 14.2 vdc agm 13.1 13.4 13.7 vdc equalize mode current truecharge 20+ 5 adc truechar...
Page 55: Ac Input Specifications
Specifications a–4 ac input specifications protection features truecharge 20+ truecharge 40+ ac input voltage range 90 – 135 vac, 50/60 hz maximum ac input current at 90 vac 6.5 a rms 12 a rms typical ac input current at 120 vac 4.6 a rms 8.5 a rms no-load ac power draw (without remote panel) less t...
Page 56: Approvals
Approvals a–5 approvals over-temperature internal charger temperature is measured. Unit shuts down and restarts as follows: • over-temperature shutdown at 62 °c • over-temperature restart at 61 °c current derating in ambient temperatures— automatic output truecharge 20+ 20 a at 30 °c to 10 a at 50 °...
Page 57
A–6.
Page 58: Battery Charging
B battery charging appendix b “battery charging” describes the truecharge+ multistage charging algorithm..
Page 59: Charging Algorithms
Battery charging b–2 charging algorithms battery type truecharge+ charges lead-acid flooded, gel, and agm (absorbed glass mat) batteries. Flooded “flooded” batteries have removable battery caps for refilling with distilled water and testing the electrolyte. Gel the sealed gel battery has its electro...
Page 60
Charging algorithms b–3 bulk charge in the first stage, known as the bulk charge, truecharge+ delivers its full- rated output current.This constant current is delivered to the batteries until the battery voltage approaches its absorption voltage—typically around 14.4 volts for 12 volt batteries. The...
Page 61: Two-Stage Charging
Battery charging b–4 figure b-1 three-stage charging profile equalization charge the equalization charge must be manually initiated because it is not required each time the battery is recharged. Equalization is a deliberate overcharge designed to return each cell to optimum condition by reducing sul...
Page 62: Battery
C battery maintenance appendix c “battery maintenance” contains procedures for maintaining the battery enclosure, battery terminals and lugs, and battery cables. It also provides a list of the clothing, tools, equipment, and supplies you should have before you begin battery maintenance..
Page 63: Maintenance Guidelines
Battery maintenance c–2 maintenance guidelines electrolyte at a minimum, check the level of the electrolyte in each battery cell once a month (for flooded batteries). It should be above the top of the plates, but not completely full. Most batteries have a plastic cup that just touches the electrolyt...
Page 64
Preparation for cleaning batteries c–3 preparation for cleaning batteries the appropriate clothing, tools, equipment, and supplies are listed below. Gather what you need before beginning. Clothing appropriate clothing could include old clothes, rubber boots, or old shoes. Battery acid is highly corr...
Page 65: Maintaining and Cleaning
Battery maintenance c–4 maintaining and cleaning follow these procedures to maintain the • battery enclosure • battery terminal and lugs • cables battery enclosure and batteries mix four ounces of baking soda with a gallon of fresh water and fill a spray bottle. Spray the solution on all exposed sur...
Page 66
Maintaining and cleaning c–5 reconnect the battery cable terminals to the battery lugs and tighten to approximately 10–15 foot-pounds using the torque wrench. If you do not have a torque wrench, use an appropriate tool to tighten the bolts reasonably snug. Do not over-tighten. After tightening the c...
Page 67
C–6.
Page 68: Product and
D product and system information appendix d “product and system information” contains the xantrex warranty for your product and return instructions. It also contains a place for you to record the serial number and date of purchase and other details of your battery charger..
Page 69: Warranty
Product and system information d–2 warranty what does this warranty cover? This limited warranty is provided by xantrex technology, inc. ("xantrex") and covers defects in workmanship and materials in your xantrex truecharge 20+ and truecharge 40+. This warranty lasts for a warranty period of 12 mont...
Page 70
Warranty d–3 direct returns may be performed according to the xantrex return material authorization policy described in your product manual. For some products, xantrex maintains a network of regional authorized service centers. Call xantrex or check our website to see if your product can be repaired...
Page 71: Disclaimer
Product and system information d–4 disclaimer product this limited warranty is the sole and exclusive warranty provided by xantrex in connection with your xantrex product and is, where permitted by law, in lieu of all other warranties, conditions, guarantees, representations, obligations and liabili...
Page 72: Return Procedure
Return material authorization policy d–5 return material authorization policy before returning a product directly to xantrex you must obtain a return material authorization (rma) number and the correct factory "ship to" address. Products must also be shipped prepaid. Product shipments will be refuse...
Page 73
Product and system information d–6 if you are returning a product to a xantrex authorized service center (asc) a xantrex return material authorization (rma) number is not required. However, you must contact the asc prior to returning the product or presenting the unit to verify any return procedures...
Page 74
Information about your truecharge+ d–7 information about your truecharge+ please record the following information when you unpack your truecharge+unit. : if you need to contact customer service, please gather the following information before calling.The information will assist the service representa...
Page 75
Product and system information d–8.
Page 76: Index
A absorption charge, battery activity during b–3 ac input specifications a–4 ac wiring requirements 2–6 agm (absorbed glass mat) batteries b–2 agm batteries, selector switch for 1–3 anti-corrosion grease c–2 b baking soda c–3 batteries agm (absorbed glass mat) b–2 first aid when working with 1–x mai...
Page 77
Index index–2 equalization charge b–4 equalization of batteries, understanding 3–7 equalizing, procedure 3–9 f failure to operate 4–4 fan speed, change in speed of 3–7 fax number for customer service d–2 features 1–2 first aid 1–xi fixed voltage mode 1–4 float charge, battery activities during b–3 f...
Page 78
Index–3 index t telephone number for customer service d–2 temperature switch description of 1–3 setting for charging 3–3 temperature, effect of in charging 3–3 terminals and lugs, maintenance of c–4 three-battery charging 1–2 three-stage charging algorithm explanation b–2 three-stage charging profil...
Page 80
Xantrex technology inc. Toll free 1 800 670 0707 direct 1 360 925 5097 fax 1 360 925 5143 customerservice@xantrex.Com www.Xantrex.Com.