Summary of HYDROS 40
Page 1
Zeos 28 zeos 38 hydros 40 hydros 50 user manual english.
Page 2: 1 Introduction
1 introduction congratulations! You have purchased a perfect product in which, without any compromise, we have connected the best existing materials made in europe and in the usa, with both our technical and recreational diving experience. While designing it, we have also consulted a considerable nu...
Page 3: 2 Ce Certification
2 ce certification the products described in the following instruction have been a subject of certification in a recognized unit and meet the requirements of 89/686/ewg directive and of the norm en1809:2001, synchronized with this directive, in its full extent; and of en 250:2003 covering scuba harn...
Page 4: 3 Safety Rules
3 safety rules 1. Before every dive, carefully inspect all elements of the equipment, including the bc. For further information on the subject, read: “pre-dive inspection”. 2. Do not dive with the bc if there are signs of defective operation, damage or wear, such a bc should be withdrawn from use un...
Page 5: 4 Bc Elements 1/2
4 bc elements 1/2 thanks to its modular design, a xdeep bc can be adjusted to every type of diving, starting with simple recreational diving with the use of a single tank and finishing with deep technical diving which requires configuration with a double tank set and stages. The bc can be used with ...
Page 6: 5 Bc Elements 2/2
5 bc elements 2/2 k-type power inflator a k-type inflator is a reliable device made of shock- proof technopolymer which is resistant to environmental conditions. The inflator valve is made of metal, which makes the inflator more resistant to freezing and it can be operated much longer than inflators...
Page 7: 5 Bc Adjustment
5 bc adjustment when you order a complete bc system, you get all elements connected and ready for use. For improved comfort and safety of use you should, however, make some final adjustments of the harness straps. The adjustment description below applies to the most basic model of harness, consistin...
Page 8: 6 Connecting The Lp Hose
6 connecting the lp hose to allow for proper operation of the inflator it must be connected to the lp port of the 1st stage of the regulator using the lp hose supplied with the bc. In order to connect the lp hose to the inflator you should gently pull at the sleeve of the lp hose’s nozzle (step 1), ...
Page 9
7 connecting the scuba tank 1/2 connecting the single scuba tank to zeos 38 and zeos 28 compensators in order to connect the tank with the bc in a reliable and safe manner you should connect the webbing as indicated in the pictures below: before connecting the tank, carefully wet the connecting stra...
Page 10
8 connecting the scuba tank 2/2 connecting the double scuba tanks to hydros 50 and hydros 40 compensators in order to connect the double scuba tank in proper and safe way, read and understand the user manual delivered with the double set. To install the bc on double tank set: 1. Put the double tank ...
Page 11: 9 Pre-Dive Inspection
9 pre-dive inspection before every dive it is necessary to follow the inspection procedures for checking the correct operation of all bc elements. Even if on a given day you have already dived using your bc, before diving again make sure that all of its elements are working correctly. 1. Check that ...
Page 12: 10 Operation
10 operation buoyancy on the surface in order to ensure maximum buoyancy on the surface, before getting into the water (or directly after ascending) inflate the bc using inflator button. Stop inflating the bc when the automatic dump valve activates. Descent in order to descend, press the purge butto...
Page 13: 11 Post-Dive Maintenance
11 post-dive maintenance disconnecting after diving, take out the weight from the weight pockets (if applicable), disconnect the lp hose from the inflator, and then disconnect the tank. Draining inflate the bc orally using the purge button of the inflator. Next turn the bc to keep the automatic dump...
Page 14: 12 Repair And Maintenance
12 repair and maintenance xdeep bcds does not contain any elements which can be repaired by the user, and so all repairs (including lubrication or replacement of worn-out elements) should be performed only by trained technicians holding certificates issued by the producer (authorized service center)...
Page 15: 12 Specification
12 specification basic parameters type toroidal wing-style bc buoyancy zeos 28: 13l zeos 38: 17l hydros 40: 18l hydros 50: 22l outer shell fabric cordura 1100 dtex inner bladder fabric nylon 440 dtex spacing between backplate mounting holes 11 inches (27.94 cm) dry bc weight (without harness) zeos 2...
Page 16
Wreckandreef piotr czernik ul.Ogrodników 3 43-227 góra polska tel: +48 12 44 66 998 e-mail: biuro@xdeep.Pl.